2. ALEKO
  3. DG14LONSSLAC1500-HD
DG14LONSSLAC1500-HD

ALEKO DG14LONSSLAC1500-HD Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the ALEKO DG14LONSSLAC1500-HD Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Phone : 253-872-3656, 253-246-8222
Kent, WA
www.AlekoProducts.com
SINGLE GATE
(SLIDING GATE)
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
Table of Contents
Important! Call Utillity Locate Before You Dig ..............................
Confirm Local Building & Safety Code .......................................
Hardware Packet.....................................................................1
Tools Needed .........................................................................1
Gate Size & Installation ............................................................1
Part 1 Post installation ........................................................2
Part 2 Gate assembly .........................................................2
Part 3 Hanging the Gates....................................................3
................................................................................................
Important Planning!
Call 811 to Locate Utillity
Before You Dig
You can also call your local utility
companies to have your area marked.
Confirm Local Building & Safety Code
Codes vary in each state and county. Especially if
Gate automation is added in the projects future. Your
local building and fire inspectors can advise you on
what your local codes are.
“Confirm all Local
building & safety
codes starting
your project.”
1
Hardware Packet
Tools Needed
Tape Measure …A Can of white paint (Athletic Striping)… 2 Stakes… Mallet…
Quick Set Concrete (7-8 bags). ..Hoe to Mix concrete…Water Bucket
…Wheelbarrow…post hole digger…Shovel…Box beam level & Line Level…
String Line… Wrenches (Sizes 3/4” & 1/2”)…Grease Gun
Gate Size / Distance Between Inside of Gate Posts
L2 = 12’ / 144 1/4”
L2 = 14’ / 168 1/4”
L2 = 16’ / 192 1/2”
2 Panels of Gates
2 Posts
2 Hinges
1 Set of Assembly Brackets
1 Set of Bolts and Nuts
2
Part 1
Install Posts
Mark the post locations with a (X) in white paint and
call 811
After utilities have been located dig holes 36” deep.
Place posts in holes and check for level and correct
distance apart. Pull the string level firm from post to
post points.
Adjust height of posts pounding down on the Posts or
adding site debris under the post to get the correct
bottom of the gate height.
Mix concrete & fill holes taking care to not move the
posts. POSTS NEED 3-4 DAYS FOR CONCRETE TO
SET.
Part 2
Gate assembly
Please assemble two part of gate with special
assembly brackets and hardware.
3
Part 3
Hanging the Gate
Bolt Hinges to hinge post.
Hang Gate on “J “Hinge and adjust as required.
Set of the Hinge
Post with Hinge
If you have any questions please visit our
web site www.AlekoProducts.com
or call us : 253-872-3656, 253-246-8222
4
Part 4
Optional
If you would like to install gate as a sliding gate,
please, consider purchasing our optional Slide Gate
Kit and extra post.
Kit includes:
2(two) Side Rollers;
2 (two) Support Gate Wheels;
1 (One) Frame Extension;
Set of Rails.
FOR MORE INFORMATION
Please visit our web site
www.AlekoProducts.com
or call us : 253-872-3656, 253-246-8222
5
Dimensions of 12, 14, 16 and 18 ft Sliding Gate Kits.
6
Sliding Gate Installation Diagram.
FOR MORE INFORMATION
Please visit our web site
www.AlekoProducts.com
or call us : 253-872-3656, 253-246-8222
/