Amluxx VIVIDPKG-8-6036BT Installation guide

VIVIDPKG-8-6036BT
Brand
Amluxx
Model
VIVIDPKG-8-6036BT
Type
Installation guide

This manual is also suitable for

Sliding Shower Door /8mm
Installation Instructions
Size:60"x78"
Electric drill
Drill(Ø3.2mm)
Drill(Ø6mm)
Cross head
screw driver
Spirit level
Tape measure
Rubber hammer
Knife
Silicone sealant
Pencil
SI
LIC
ON
E
=(58.03"-60")x78"
H20
H23
H22
H21
H01
H02
H03
H05
H06
H07
H04a
H04b
H08
H09
H10
H11
H12
H18
H17
H19
H14L
H15
H13
H16
2
H20
H21
H25
3
6mm
4mm
2.5mm
4X
4X
4X
4X
φ6mm
H05
H06
H07
H01H01
0.
39
"(
1
0
mm
)
-Put the wall profile H01(X1)against
the wall,and ensure it is vertical by
spirit level.
-Mark the holes on the wall.
-Drill the holes accordingly.
-Insert the wall plugs H05(x4)into the
holes.
-Fasten the wall profile H01 on the wall
with screws H07(X4) and washers
H06(X4).
Slider is ok to be installed in left and right hand. Below steps are based on right hand.
For left hand ,please follow below steps in mirror direction.
4
H03
H21
H21
H17
H24
X1
- Insert fix panel H03 into the channel of wall profile.
-Loose the part H21(X2) first.
-Then put the part H21(X2) on the top rail H17,
-Fixed the parts H21(X2) on the top rail with the
hex key H24.
H24
5
6mm
6mm
6mm
H19
H20
H20
H03
H24
X1
X2
X1
-Fix the part H20(X1) on the top rail with hex key H24.
-Inser the wall barkets H19(2X) on the both side of top
rail.
- Install the top rail with the wall brakets on the fixed panel H03 with the parts H21(X).
-Mark the position of the wall brakets on the wall.
6
6mm
2.5mm
H03
H03
-Disassemble the wall brakets H19(X2) from the top rail with the hex key H24.
-Mark the holes of the wall brakets on the wall according to the position.
-Take off the wall seats from the wall brakets H19(x2).
-Disassemble the rail profile H17 from fix panel H03 by loose fixing part H21(X2)
with hex key H24.
7
H05
H23
H03
H03
X4
X4
-Drill the holes according to the position.
-Insert the wall plugs H05(X4) on the wall.
-Fix the wall seats on the wall with the screws H24(X4).
H23
-Insert rail profile H17 into the wall bracket H19 and fasten them together with inner
screw.
-Assemble fixing part H21 on the rail profile through fixing panel.
8
3
0
"-3
1
"
(
765
-
7
90m
m
)
3
0
"
-
3
1"(76
5
-79
0mm)
H02
H25
H25
H14L
H15
H16
H03
X1
X1
-Adjust the position of fix panel to meet with opening
requirement.Please make sure the same opening both
on top and bottom.
-Insert the single blade sealer H02(X1) between glass
panel by tool H25 and wall profile from outside of cabin.
-Apply silicone glue on the back of the
bottom anti-water profile H15(X1) and
sliding guideH14L (X1)and end cover
H16(X1).
9
H14L
H15
H16
H04a
H03
H03
-Put sliding guide H14L(X1) next to the fix panel.
Insert bottom profile H15into the guide.
-Put cover H16(X1)on the other end of H15.
-Apply vertical sealer H04a(X1) on the edge of fixing
panel H03.
10
H24
X2
H18
H12
H24
H08
H08
H04b
H09
H13
-Apply the vertical sealer H04b(X1) on
the edge of slider panel H08;
-Apply the magnetic sealer H09 on the
sliding panel edge next to the handle.
-Attach the bottom anti-water sealer H13
on the bottom of sliding panel.
-Mount the rollers H18(X2) on the sliding
panel H08 by hex kety H24.
-Mount the handle H12(X1) on the sliding
panel H08.
11
4mm
4mm
2.5mm
H10
H11
H03
H08
- Mount sliding panel on the rail profile. Put the top roller on the top of rail profile and
put anti-jump part into the channel of rail profile. Make sure the bottom sealer of
sliding panel into the channel of bottom sliding bracket.
-Insert the magnetic strip H10 into the small wall
jamb H11.
H08
H03
-Put 2 magnetic strip closed on the sliding panel.
-Close the door to mark the position of samll jamb.
12
H05
H07
H22
H10
H22
H08
H03
H08
-Take off the magnetic strip out off the small wall jamb.
-Put the samll wall jamb H11 on the wall according to
the mark.
-Mark the holes position,and drill the holes accordingly.
-Insert wall plugs H05(X4) into the holes.
-Fix the small wall jamb on the wall with screws H07(X4).
-Insert magnetic strip H10 into the channel of small wall jamb.
-Put top cover H22 on the big wall profile.
13
1-2MM
!
!
NO
OK
X2
H24
4mm
H18
H24
H08
H08
H03
H03
-Mount another rollers H18(X2) on the sliding panel H08
under the top rail with the hex key H24.
-Ensure there have 1-2mm distance between rollers and
top rail.
-The top roller is adjustable to make the door vertical.
-Take off the back cover ,turn the nut until the door is vertical with magnetic strip
closing well.
-Put the back cover on the rollers.
4mm
2.5mm
V18G27
Technical and Customer Support : 1-312-666-3552
We have taken great care to ensure that this product
reaches you in perfect condition. However should any
parts be damaged or missing please contact your point
of purchase. This does not affect your statutory rights.
In addition if you require replacement parts your point
of purchase will be happy to assist.
Cleaning and Maintenance:
Sealant drying times may vary in cold damp conditions
and will be extended where thicker beads of sealant are
applied. Allow sealant to dry completely before exposing
to water.
Please do not use abrasive or strong cleaning
solutions on the shower enclosure, such as
alcohol, petroleum liquids or any other chemical
cleaner.
Should there be any dirty stains on the shower
enclosure, please clean it with a soft lint free cloth
and warm soapy water. Please rinse it with clean
water afterwards.
- Apply silicone sealant to the outside of the enclosure.
Please note: Do not apply silicone sealant to the inside
of the enclosure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Amluxx VIVIDPKG-8-6036BT Installation guide

VIVIDPKG-8-6036BT
Brand
Amluxx
Model
VIVIDPKG-8-6036BT
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents