Champion Power Equipment 50067 User manual

Brand
Champion Power Equipment
Model
50067
Type
User manual

Champion Power Equipment 50067 is a swivel wall mount metal hose reel. This swivel function is designed to allow you to reorient the reel as needed, by lifting the locking knob to release the lock and rotate the reel to the next locking position. It has a leader hose that can be attached to the water inlet, which is equipped with rubber washers in the couplings. The unit can be mounted to either flat wood frame construction or stucco, concrete, or brick masonry construction and can be used for various watering and cleaning tasks.

Champion Power Equipment 50067 is a swivel wall mount metal hose reel. This swivel function is designed to allow you to reorient the reel as needed, by lifting the locking knob to release the lock and rotate the reel to the next locking position. It has a leader hose that can be attached to the water inlet, which is equipped with rubber washers in the couplings. The unit can be mounted to either flat wood frame construction or stucco, concrete, or brick masonry construction and can be used for various watering and cleaning tasks.

OWNER’S MANUAL
& OPERATING INSTRUCTIONS
10006 Santa Fe Springs Road
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
Swivel Wall Mount
METAL HOSE REEL
SAVE THESE INSTRUCTIONS
Important safety instructions
are included in this manual.
MADE IN CHINA
REV 50067-20120516
50067
MODEL NUMBER
warranty_badges.pdf 1 8/18/11 10:45 AM
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info and Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
50067
METAL HOSE REEL
Swivel Wall Mount
TABLE OF CONTENTS
Manual Conventions ....................... 1
Introduction ............................ 2
Before You Begin ...................... 2
Parts ................................ 3
Assembly .............................. 4
Attaching the Crank Knob ................. 4
Mounting to Concrete or
Brick Mansonry Construction .............. 4
Mounting to Flat Wood Frame Construction ..... 4
Attaching the Leader Hose ................ 4
Attaching the Swivel Arm ................. 5
Operation .............................. 6
Ushing the Swivel Function ................ 6
Maintenance ............................ 7
Annual Seal Lubrication .................. 7
Winter Preparation ..................... 7
Warranty .............................. 8
Warranty Qualifications .................. 8
Repair/Replacement Warranty .............. 8
Do Not Return The Unit To
The Place Of Purchase ................... 8
Warranty Exclusions. . . . . . . . . . . . . . . . . . . . . 8
Normal Wear ....................... 8
Installation, Use and Maintenance ......... 8
Other Exclusions ..................... 8
Limits of Implied Warranty
and Consequential Damage ............. 8
Contact Information ..................... 8
Address ........................... 8
Customer Service .................... 8
Technical Service .................... 8
Specifications ........................... 9
Parts Diagram ......................... 9
Parts List ........................... 10
1 REV 50067-20120516
ENGLISH 50067
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
MANUAL CONVENTIONS
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
WARNING
If you have questions regarding your hose reel, we can
help. Please call our help line at 1-877-338-0999
NOTE
REV 50067-20120516 2
50067 ENGLISH
Before You Begin
This product has been packaged to ensure it arrives in best possible condition. Please be careful
when unpacking. Read instructions prior to assembly. This kit contains parts that can be damaged if
incorrectly assembled. Please follow instructions. Champion Power Equipment is not responsible for
replacing parts damaged due to incorrect assembly.
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
Model Number
Serial Number
Date of Purchase
Purchase Location
1-877-338-0999
50067
INTRODUCTION
Please consider carefully the appropriate method
to be used in mounting this hose reel. Hardware
is included for your convenience, but may not be
suitable for all mounting conditions. Some surfaces
like vinyl siding or stucco may require special
considerations or additional hardware. Improper
mounting can cause personal injury or property
damage. If you are unsure, contact a home
improvement professional
CAUTION
The coupling contains lead, a chemical known to
the state of California to cause cancer and birth
defects or other reproductive harm.
WASH HANDS after handling.
This hose is not for drinking water use.
WARNING
Do not completely tighten bolts until assembly is
completed. For easier assembly, we recommend that
two people assemble this product.
NOTE
3 REV 50067-20120516
ENGLISH 50067
Tools Required
Replacement Parts
– Powered hand drill or hammer drill with
3/8 in. (10 mm) masonry drill bit or 1/4 in. (6 mm)
standard drill bit
– Small hammer or mallet
– #3 Phillips screwdriver
– 10 mm Socket or Wrench
For replacement parts, contact:
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free:1-877-338-0999
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
PARTS
Parts Included
– Hose Reel with Swivel Arm ................. 1
– 6 ft. (1.8 m) Leader Hose ................. 1
– Seal Washer ........................... 2
– Self Tapping Screw ...................... 4
– Plastic Expand Sleeve .................... 4
– Inlet Base ............................ 1
– Inlet Clip ............................. 1
– Rewind Handle ......................... 1
– Flat Washer ø5 ......................... 1
– Screw Bolt M5 x 10 ...................... 1
Other components may be identified by part
numbers marked on the part.
Anchors for masonry application only.
Lift and twist to disengage lock.
NOTE
REV 50067-20120516 4
50067 ENGLISH
Attaching The Crank Knob
Tools Required:
– #3 Phillips screwdriver
Instructions:
1. Place crank knob over its mounting.
2. Secure in place using washer and screw provided.
Mounting to Stucco, Concrete or
Brick Masonry Construction
Tools Required:
– 10 mm Socket or Wrench
– Powered hand drill or hammer drill with 3/8 in.
(10 mm) masonry drill bit
– Small hammer or mallet
Instructions:
1. Determine the mounting hole locations using the
mounting stencil provided with this manual.
2. Drill four (4) holes 2.4 in. (60 mm) deep.
3. Insert the masonry anchors provided, into each hole.
These may need to be seated by tapping with the
mallet.
4. Open the locking hinge and lock in a position that
allows access to the mounting brackets.
5. Locate unit over holes and secure with lag screws
provided.
Mounting to Flat Wood Frame Construction
Tools Required:
– 10 mm Socket or Wrench
– Powered hand drill with 1/4 in. (6 mm) standard drill bit
Instructions:
1. Determine the mounting hole locations using the
mounting stencil provided with this manual.
2. Drill four (4) holes 2.4 in. (60 mm) deep.
3. Open the locking hinge and lock in a position that
allows access to the mounting brackets.
4. Locate unit over holes and secure with lag screws
provided.
Attaching the Leader Hose
Instructions:
1. Remove leader hose from the reel.
2. Verify placement of rubber washers in leader hose
couplings.
3. Install one end of the leader hose to the water inlet
tightening the threaded coupling by hand.
ASSEMBLY
To prevent damage or injury, be sure to verify that
holes align with stud locations in the wall.
CAUTION
5 REV 50067-20120516
ENGLISH 50067
ASSEMBLY
A
B
C
Attaching The Swivel Arm
Instructions:
1. On either side of the upper swivel arm axle (A), press
and hold both spring loaded detents (B).
2. Insert upper swivel arm axle into lower swivel arm
axle sleeve (C), until detents release.
REV 50067-20120516 6
50067 ENGLISH
OPERATION
Using the Swivel Function
This unit is designed with a locking hinge that allows you
to reorient the reel as needed.
Simply lift the locking knob as seen in figure to release
the lock.
This will allow you to rotate the reel to the next locking
position.
The hinge will automatically lock in the new position.
7 REV 50067-20120516
ENGLISH 50067
MAINTENANCE
Annual Seal Lubrication
To prevent leaks and to lengthen seal life, the water inlet
seals should be lubricated annually. (See below).
1. Stop the flow of water to the unit by shutting the
faucet valve.
2. Release locking lever.
3. Pull the inlet tube from the frame of the unit.
4. Lubricate the seals as indicated. Any white lithium
spray is recommended.
5. Replace the inlet tube and close the locking lever.
Winter Preparation
To prevent damage from expanding ice, always
disconnect and drain all hoses prior to freezing
conditions.
REV 50067-20120516 8
50067 ENGLISH
WARRANTY
CHAMPION POWER EQUIPMENT
2-YEAR LIMITED WARRANTY
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof
of purchase within ten (10) days of the date of purchase.
Limited Repair/Replacement Warranty
CPE warrants to the original purchaser that the
components will be free of defects in material and
workmanship for a period of two (2) years from the
original date of purchase.
Transportation charges on product submitted for
repair or replacement under this warranty are the sole
responsibility of the purchaser. This warranty applies
only to the original purchaser and is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will
troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair or replacement of the
defective part or component at a CPE Service Centre.
CPE will provide you with a case number for warranty
service. Please keep it for future reference. Repairs
or replacements without prior authorization, or at an
unauthorized repair facility, will not be covered by this
warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
This warranty does not cover repair when normal use has
exhausted the life of a part or the equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labour if this
hose reel is deemed to have been misused, neglected,
involved in an accident, abused, modified, installed
improperly or connected incorrectly to any hose kit.
Other Exclusions
This warranty excludes:
– Cosmetic defects such as paint, decals, etc.
– Failures due to acts of God and other force majeure
events beyond the manufacturer’s control.
– Problems cause by parts that are not original
Champion Power Equipment parts.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or
any incidental or consequential claim by anyone from
using this hose reel.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit. This
warranty gives you certain legal rights which may change
from province to province. Your state may also have
other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free:1-877-338-0999
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
WARRANTY
9 REV 50067-20120516
ENGLISH 50067
SPECIFICATIONS
Parts Diagram
3 0
3 4
3 5 3 6
3 7
3 8
4 2
3 5
4 1
4 0
3 9
3 3
3 2
3 1
2 9
1 5
2 8
1 9
1 8
2 1
2 0
2 6
2 7
2 5
2 4
2 3
2 2
1 7
1 6
7
1
341 4
6
8
1 1 5
1 3
1 0
1 2
9
2
REV 50067-20120516 10
50067 ENGLISH
SPECIFICATIONS
# Part Number Description Qty
1 50067- 01 Right Plate 1
2 50067- 02 Left Plate 1
3 50067- 03 Centre Hub 1
4 50067- 04 Outlet 1
5 50067- 05 Inlet 1
6 50067-06 Right Decorative Cover 1
7 50067- 07 Rewind Handle 1
8 50067- 08 Right Cover 1
9 50067- 09 Left Cover 1
10 50067-10 Inlet Base 1
11 50067-11 Inlet Clip 1
12 50067-12 Lock Handle 1
13 50067-13 Swivel Cover 1
14 50067-14 Seal Washer, ø14-ø23.8-3.1 1
15 50067-15 Seal Washer, ø15-ø26-2.8 2
16 50067-16 Lock Core 1
17 50 067-17 Cutlet Gag 1
18 50067-18 Support Axle 1
19 50 067-19 Axle Base 1
20 50067-20 Up Support Tube 1
21 50067-21 Up Swivel Axle 1
22 50067-22 Insert Lock External Tube 1
23 50067-23 Insert Lock Spring 1
# Part Number Description Qty
24 50067-24 Insert Lock Core 1
25 50067-25 Spring Lamination 1
26 50067-26 Insert Lock Ring 1
27 50067-27 Bottom Swivel Axle 1
28 50067-28 Bottom Support Tube 1
29
50067-29 Self Tapping Screw, ST6.0
x 60
4
30
50067-30 Plastic Expand Sleeve, ø10
x 50
4
31 50067-31 Mount Bracket 1
32 50067-32 Brass Fitting, 3/4-11.5NH 2
33 50067-33 Brass Sleeve 2
34
50067-34 Leader Hose, Length 6 ft.
(2 m)
1
35 50067-35 Screw Bolt M5 x 10 3
36 50067-36 Flat Washer, ø5 1
37
50067-37 Self Tapping Screw, ST5.0
x 20
12
38
50067-38 Self Tapping Screw, ST4.0
x 20
2
39 50067-39 Collar 1
40 50067-40 Flat Washer, ø38.5-ø42-1.5 1
41 50067- 41 Stop Nut M5 2
42 50067-42 O-ring 2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Champion Power Equipment 50067 User manual

Brand
Champion Power Equipment
Model
50067
Type
User manual

Champion Power Equipment 50067 is a swivel wall mount metal hose reel. This swivel function is designed to allow you to reorient the reel as needed, by lifting the locking knob to release the lock and rotate the reel to the next locking position. It has a leader hose that can be attached to the water inlet, which is equipped with rubber washers in the couplings. The unit can be mounted to either flat wood frame construction or stucco, concrete, or brick masonry construction and can be used for various watering and cleaning tasks.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents