Frigidaire FAM156R1A15 Owner's manual

Brand: Frigidaire

Model: FAM156R1A15

Type: Owner's manual

USE & CARE MANUAL

Contents

2 Warranty

3 Product Registration

3 Packaging

3 Normal Sounds

4 Important Safety Instructions

4 Operation of Current Device

5-10 Air Conditioner Features

11 Care and Cleaning

11 Energy Saving ideas

12 Avoid Service Checklist

NOTE: This USE & CARE MANUAL

provides specific operating instructions

for your model. Use the roomair

conditioneronlyas instructedinthisUSE

& CARE MANUAL instructionsare not

meant to cover everypossiblecondition

and situationthat may occur.Common

senseand cautionmustbe practicedwhen

installing,operating,end maintainingany

appliance.

READ AND SAVE THESE INSTRUCTIONS

MEDIAN and HEAVY DUTY

ELECTRONIC CONTROL

AIR CONDITIONERS

PIN 66129901148

ROOM AiR CONDiTiONER WARRANTY

Yourproductisprotectedby thiswarranty

Yourapplianceiswarrantedby Electrolux.ElectroluxhasauthorizedFrigidaireConsumerServicesandtheirauthorized servicersto performserviceunder this

warranty.Electmluxauthorizesnoone else tochangeor add toany of theseobligationsunderthiswarranty.Any obligationsforservice and partsunderthis

warrantymustbe performedbyFrigidaireConsumerServicesoran authorizedFrigidaireservicer.

WARRANTY FRIGIDAIRE, THROUGH ITS AUTHORIZED THE CONSUMER WILL BE

PERIOD SERVICERS, WILL: RESPONSIBLE FOR:

FULLONE-YEAR One year from Pay all costs for repairing or replacing parts of Costs of service calls that are listed under

WARRANTY original purchase this appliance which prove to be defective in NOR-MAL RESPONSIBILITIES OF THE

date. materials or workmanship. CONSUMER.*

LIMITED2-5 Second through fifth Repair or replace any parts in the Sealed )iagnostic costs and any removal,

_EAR ears from original Refrigeration System (compressor, condenser, ransportation end reinstallation costs

In/ARRAHTY ,urchasedate. evaporator and tubing) proves to be defective in vhich are required because of service.

[SealedSystern) materialsorworkmanship. _osts for labor, parts and transportation

bther than with respect to the Sealed

Refrigeration System.

* NORMAL

RESPONSiBILiTIES OF"

THE CONSUMER

This warranty applies only to products in ordinary hau_hoid usa, and the consumer is raeponeibte for the items

listed below.

1. Properuseof the appliancein accordancewithinstructionsprovidedwiththeproduct.

2. Properinstallationbyanauthorizedservicerinaccerdancewith inslructionsprovidedwiththe applianceand inaccerdance

withalllocalplumbing,alec_ical and/or gascodes.

3. Propercennec_ontea groundedpewarsupplyofsufficientvoltege,replacernentofblownfuses,repair ofleasecennections

ordefectsinhousewiring.

4. Expensester maldngtheappliance accessibleter servicing,suchasremoval oftrim,cupboards,shalvas,etc.,whichare

nota partoftheappliancewhenitwas shippedfromthe factory.

5. Damagaste finish after installation.

6. Damageto unitafterremovalfrompeckaglngcarton.

EXCLUSIONS

iF YOU NEED SERVICE

This warranty doea not cover the following:

1. CONSEQUENTIAL OR INCIDENTALDAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTINGFROMANY BREACHOF THIS WRI'I-i'ENORANY IMPLIEDWARRANTS.Note: Somestatesdo notallow

theexclusionor limitationof incidentalor consequentialdamages,so this limitationor exclusionmay notapplyto you.

2. Servicecallswhichde notinvolvemalfunction or defectsin workmanshipor material, orforappliancesnotinordinary

householduse.Theconsumershallpayfor suchservicecells.

3. Damagascausedby services performedby personsotherthanauthorizedFrigidaireservicers; use of partsotherthan

FrigidaireGenuineRenewalParts;obtainedfrom personsotherthansuchservicers;orexternalcausessuchasabuse,

misuse, inadequatepowersupplyoractsof God.

4. Produotswith_riginalserialnumbersthathavebasnrem_ved_ralteredandcannotbereodi_ydeterminod_

Keepyour billof sale,delivery slip,orsomeotherappropriate paymentrecord.The dateonthe billestablishesthe warranty

periodshouldservice berequired.Ifserviceisperformed,itisinyourbestinteresttoobtainandkeepallreceipts.Thiswritten

warrantygivesyou specificlegal rights.You may also have other rights that vary from stateto state. Serviceunderthis

warrantymustbe obtainedbyfollowing thesesteps,inorder:

1. Conteot FrigidaireConsumerServicesoran authorizedFrigidaireservicer.

2. Ifthereisa questionastowhereto obtainservice, contactourConsumerRelationsDepartmentat:

Frigidaire

P.O. Box212378

Augusta,GA30917

800-444-4944

CANADA

ElectroluxCanadaGroup

6150 McLaughlinRoad

Mississauga,OntarioL5R4C2

1-866-213-9397

Productfeaturesorspecificationsas describedorillustratedare subjecttochangewithoutnotice.Allwarrantiesaremadeby

Electrolux.

Thiswarrantyapplies onlyinthe 50 statesofthe U.S.A., PuertoRiceand Canada.

FOR SERVICE CALL 1-800-444-4944.

Product Registration

Record Your Model and Serial Numbers

Recordinthespaceprovidedbelowthemodelandserialnumbers,Onall models,theserial

plateis locatedontheoutsideofthecabinet,

Model No

Serial No.

The self-addressed PRODUCT REGISTRATION CARD should be filled incompletely, signed

and returned to the Frigidaire Company,

Packaging Remove all packaging from inside the unit ,also any inserts placed into

the side louvers.

s_ps

Pac/dng /nserts

Normal Sounds

High Pitched Cha#er

Today'shighefficiencycompressors

may have a high pitched chatter

duringthe coolingcycle.

Sound ofRushing Air ..............

Atthefrontoftheunit,youmay

hear the soundof rushing=,ir

beingmovedbyths fan,

Gur#/e/F/iss

=Gurglingorhissing"noisemaybeheard

due to refrigerant passing through

evaporatorduringnormaloperation.

l[/bration

Unitmay vibrate and make noise

because of poorwall or window

constructionorincorrectinstallation.

Ping/n# or Swishing

Dropletsofwaterhittingcondenser

duringnormaloperationmaycause

"pingingor swishing"sounds,

Important Safety

instructions

The power supply cord with

this air conditioner contains a current

detectiondevicedesignedtoreducetherisk

oftim.

Please refer to the section'Operation of

CurrentDevice'for details.

Inthe eventthatthe powersupplycordis

damaged,itcannotbe repaireditmustbe

replaced with a cord from the Product

Manufacturer.

Avoidfire hazardor electric

shock.Do notusean extensioncordoran

adaptorplug.Donotremoveanyprongfrom

thepowercord.

Grounding type wall

receptacle

not, under any_

circumstances, cut,

remove,or bypassthe

Power supply cord

with 3-prong grounding

plug and current

detection device

Reed all instructions before using this air conditioner.

For Your Safety

Do notstoreorusegasolineorotherflammablevaporsand liquidsinthevicinityofthisorany

otherappliance,Read productlabelsfor flammability and otherwarnings,

ri_ Prevent Accidents

Toreducetheriskoffire, electricalshock,orinjurytopersonswhenusingyourairconditioner,

followbasicprecautions,includingthefollowing:

Besuretheelectricalserviceisadequateforthe modelyouhavechosen.Thisinformation

canbefoundontheserialplate,whichislocatedonthesideofthecabinetand behindthe

grille.

Ifthe air conditioner isto be installedin a window,youwill probablywanttoclean both

sidesof the glassfirst. Ifthewindow isa triple-tracktypewith a screen panelincluded,

removethescreencompletely beforeinstallation.

Be sure the air conditionerhas been securelyand correctly installedaccordingto the

separate installationinstructionsprovidedwith this manual. Save this manual and the

installationinstructionsfor possiblefuture usein removingor reinstallingthisunit.

• When handlingtheair conditioner, becarefultoavoidcutsfromsharpmetalfins onfront

and rearcoils.

Electrical information

The completeelectrical ratingofyournewmorn air conditionerisstatedon theserialplate.

Refertothe ratingwhen checkingthe electrical requirements.

Be sure the air conditioner is properlygrounded.To minimizeshockand fire hazards,

propergroundingisimportant.The powercord isequippedwith a three-pronggrounding

plugforprotectionagainstshockhazards.

• Yourair conditionermustbe used in a properlygroundedwall receptacle. Ifthe wall

receptacleyouintendtouseisnotadequatelygroundedorprotectedbyatimedelayfuse

or circuitbreaker,havea qualifiedelectricianinstalltheproperreceptacle.

Do not runair conditionerwithouttheoutside protectivecover in place. This could

resultin mechanicaldamagewithin theairconditioner.

Do not use an extension cord or anadapter plug,

READ THiS SECTION BEFORE ATTEMPTING TO OPERATE AiR CONDITIONER.

Operation of Current

Device

Plug in &

press RESE']

NOTE: Some plugs havo

buttons on the top.

The powersupplycord contains a currentdevicethatsensesdamagetothepowercord. To

testyourpowersupplycord dothefollowing:

1. PlugintheAirConditioner.

2. The powersupplycord willhaveTWO buttonsonthe plughead. Pressthe TEST button.

Youwill noticea clickas the RESET buttonpopsout.

3. PresstheRESET button.Againyouwillnoticea clickas the buttonengages.

4. The powersupplycord isnowsupplyingelectricitytotheunit.(Onsomeproductsthisis

also indicatedbya lighton theplughead).

NOTES:

Do notusethisdevicetoturnthe uniton oroff.

• AlwaysmakesuretheRESET buttonispushedinforcorrect operation.

• The powersupplycord mustbe replacedifitfails to resetwheneithertheTEST buttonis

pushed,oritcannotbe reset.Anewonecanbe obtainedfromtheproductmanufacturer.

Ifpowersupplycord isdamaged, itCANNOT be repaired.It MUST be replacedbyone

obtainedfromtheproductmanufacturer.

Air Conditioner Features ELECTRONIC CONTROL OPERATING iNSTRUCTiONS

Beforeyoubegin,thoroughlyfarsiliarizeyourselfwiththecontrolpanelandremoteasshown

ON/OFF LIGHT belowand allitsfunctions,thenfollowthesymbolforthefunctionsyoudesire,The unit can

be controlled by the touch pad alone or with the remote,

ADJUSTS

TEMP & SETS

TIME FAN

ADJUSTS DISPLAYS

TEMP & TEMPERATURE/TIME

SETS ACTIVATE

MODE TIMER

AUTO FAN

REMOTE CONTROL

Fig."A" FORHEATMODELS

ON/OFF

ADJUSTS

TEMP&

TIME

SETS

MODE

Fig. "B"

REMOTE CONTROL

wlDISPLAY &

REMOTE SENSING

BUTTON

SETS

SPEED

TIMER

AUTO FAN

RESET BUTTON

ACTIVATES

TIMER

TOUCH PAD

ADJUSTS

TEMP &

TIME

_ CLEANAIR

FEATURE

(some models)

LIGHT

SETS

FAN

SPEED

SETS

MODE

TIMER

AUTO FAN

STANDARD REMOTE

Battery Size: AAA

Warning: do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc),or rechargeable(nickel-cadmium) battedes.

NOTE: The following instructions mprseent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON: YOU WILL SEE:

DO THIS:

PRESS ON/OFF

BUTTON

Air Conditioner Features

(continued)

TO CHANGE TEMPERATURE

SETTING:

YOU WiLL SEE:

DO THIS:

PRESS TO

RAISE

LOWER

Note: Tap or hold either up (A) or down (V) button untilthe desired temperature is seen on the display, This temperature will be automati-

cally maintained anywhere between 60°F (160C) and 90°F (32°C) for cooling mode, The temperature will be automatically maintained anywh-

ere between 55°F (13°C) and 80°F (27°C) for heating mode, If you want the display to read the actual room temperature, See "To Operate

on Fan Only" section on Page 7,

TO ADJUST FAN SPEEDS: YOU WiLL SEE : LIGHT On

DO THIS:

PRESS

TO SELECT

TO USE AUTO FAN FEATURE: YOU WiLL SEE:

LIGHT On

DO THIS:

PRESS

FAN BU'N'ON

SELECTAUTO

Note: Fan speed starts at High Speed and adjusts to a slower speed as the room temperature dictates, For example if the room doesn't

get too warm, it will stay at the slowest speed, If the room temperature rises quickly,such as a door being opened, itwill automatically go

to the highest speed, The fan speeds will re-adjust back tothe slowest speed as the room returns to the original set temperature,

Air Conditioner Features

(continued)

TO OPERATE ON FAN ONLY:

LIGHT On

YOU WILL SEE:

DO THIS:

PRESS

MODE BUTTON

CHOOSE

FANONLY

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air, (Remember to open the

vent during this function, but keep it closed during cooling for maximum cooling efficiency) You can choose any fan speed you prefer, (Exc-

ept "Auto Fan"),

During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.

Fan Only cannot be selected when the unit is in the 'Remote Sensing' Mode, (On those units with that feature),

TO USE THE

ENERGY SAVER FEATURE:

LIGHT On

YOU WiLL SEE:

DO THIS:

PRESS

MODE BUll'O N

CHOOSE

ENERGY SAVER

Note: In this mode, the fan will continue to run for another 3 minutes after the compressor shuts off, The fan then cycles on for 2 minutes

at 10 minute intervals until the room tam perature is above the set temperature, at which time the the cooling system turns back on,

TIMER: DELAY STARTISTOP FEATURE:

LIGHT On

FIRST

DOTHIS:

PRESS

YOU WILL SEE HOW MUCH TIME iS CHOSEN:

THEN

PRESS

TEMPKIMER

SET BUTTON

Note 1: For Delay Stop, the unit must be in the On position.

Note 2: For Delay Start, the unit must be in the Off position,

First, PRESS TIME BUTTON

Then to adjust timer setting, tap or hold the UP arrow ( A ) or the DOWN arrow ( V ) to change delay timer at, 5 hour increments, up to 10

hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start

mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the

set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the con-

trol will automatically change the display back to the hours remaining untilthe unitwill start/stop, PRESSING the unit On/Off button at any

time will cancel the Delay Start/Stop function. The Delay StartJStop Feature will work untilthe unit either starts or stops. Once that happens

he above steps have to be repeated again,

Air Conditioner Features

(continued)

CHECK FILTER FEATURE:

LIGHT On

YOU WILL SEE:

Note: This feature isa reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will

illuminate after 250 hours of operation, To reset after cleaning the filter, press the "Check Filter" button end the light will go off,

CLF_ANAIRFF_ATURE(onsomemodels): YOU WILL SEE: LIGHT On

DO THIS:

PRESS

CLEAN AIR

BUTTON

Note: When this feature is "ON", the electronic air purifierisenergized to remove pollenand impudUesfrom the air. To cancel this feature,

press the Clean Air button (the LIGHT will turn off).

Note: This feature can be activated on the unittouchpad ONLY,

SLEEP FEATURE:

YOU WILL SEE: LIGHT On

DO THIS:

PRESS

SLEEP BU3-i'ON

Note: In this "MODE" the set temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then

increase by another 2 degrees F after an additional 30 minutes, This new temperature will be maintained for 7 hours before itreturns to the or-

iginally selected temperature, This ends the "Sleep" MODE and the unit will continue to operate as originally programmed, The "Sleep"

MODE program can be cancelled at any time during operation by again pressing the "Sleep" button.

Air Conditioner Features

(continued)

REMOTE SENSING FEATURE

(on some models) :

DO THIS:

PRESS REMOTE

SENSING

BUTTON ON

LIGHT pulsing On & Offintermittently.

!_iiiiii!:ii_

i¸!¸¸¸¸!¸i¸i!!¸_ '_

NOTE:Unit display shows"set"temperature NOTE: Remote display

is actual temperature at

remote control only

Note: This feature can be activated from the remote control ONLY,the unit must be in a cooling mode.

To activate the remote sensing feature,point the remote control towards the unit and press the remote sensing button.Next,use the

buttons to set the desired temperature at the remote.(Note that the set temperature will only be displayed on the unit itself).The LIGHT on

the unit control will pulse to indicate it received the signal.The LIGHT on the remote control will pulse each time it sends a signal.It will con-

tinue to send this signal until the feature is deactivated by pressing the remote sensing button.If the unit does not receive the remote sensing

signal during any 3 minute interval,the unit will beep to indicate the remote sensing mode has ended.The display on the remote control indicates

the temperature at the remote ONLY. The unit display indicates the set temperature.

Remote Sensing:The Remote Sensing function is terminated using the remote control Start/Stop button or the Remote Sensing

Stop button, and also the main Start/Stop button on the unit.

HEATING FEATURE (on some modes) LIGHT On YOU WILL SEE:

DO THIS:

PRESS

MODE BUTTON

SELECT HEAT i

Note: This feature can be used with any combination of FAN Speeds(Low speed only on 115V models), Timer, or Sleep Modes.When in the

"Heat" Mode,the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between 55 °F(13"C)

and 80°F(27"C)When the room set temperature is satisfied,the fan will cycle off and on to circulate and sample the room air.

TO TURN UNIT OFF:

YOU WILL SEE:

DO THIS:

PRESS

ON/OFF BUTTON

Note: When unit is shut off in the Heat Mode, the fan will continue to run for a few seconds to dissipate

residual heat within the unit.

Air Conditioner Features

(continued)

FAULT CODES

If the display reads"HS", a sensor has failed.

Contact your Authorized Frigidaire Service

Center,

If the display reads"AS", a sensor has failed.

Contact your Authorized Frigidaire Service

Center.

If the display reads"ES", a sensor has failed.

Contact your Authorized Frigidaire Service

Center.

ADDITIONAL THINGS YOU SHOULD KNOW

Now thot you hove mostared the operating procedure,here ore more features in your control that you should become familiar with:

• The '_oor' circuithasan automatic3 minute timedelayedstartifthe unitisturnedoffand on

_ quickly.This preventsoverheating ofthe compressorand possible circuitbreaker tripping.The /_\

fan willcontinuetorunduringthis times.

° The control will maintain the set temperature within 2 degrees Fahrenheit, betwean 60F and 90F degrees.

= The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.To convert from one to the other and back,

Press and hold the"TEMP/TIMER"Up ( A ) and Down ( V ) buttons together for 3 seconds.

Fresh Air Vent Control(On some models)

The Fresh Air Vent allows the air conditioner to:

1, Recirculata inside air - Vent Closed (see Fig, 1)

2, Draw fresh air into the room - Vent Open (see Fig, 2)

3, Exchange air from the room ond draws fresh oir intothe room - Vent ond Exhoust

Open (see Fig, 3)

Fig. 1 (OFF)

Fig. 2 (FRESH AIR)

Fig. 3 (VENT)

(4-WAY)

The louvers will allow you to direct the oir T'lowUp or Down and Left or Right throughout

the room as neaded.Rotata the Auger Wheel Up or Down until the desired direction is

obtained.

AUGER WHEEL

Care and Cleaning

Cleanyourair conditioneroccasionallyto keep it lookingnew. Be sure to unplug the

unit before cleaningto prevent shock or fire hazards.

Air Filter Cleaning

The air filter shouldbe checkedat leastonce a monthto see ifcleaningis necessary

Trappedparticlesin the filtercan buildup and cause an accumulationof froston the

coolingcoils

• PushtheventhandletotheVentCIosedposition(whereapplicable)

• Openthefrontpanel

• Graspthefilterbythecenterand pullup and out

• Wash the filter using liquiddishwashingdetergent and warm water Rinse filter

thoroughly Gentlyshake excesswaterfromthe filter Besure filteristhoroughlydry

beforereplacing.

• Or, insteadofwashingyou may vacuumthefilterclean.

Cabinet Cleaning

• Besuretounplugtheairconditionertopreventshockor firehazard The cabinetand

front maybedustedwithanoil-freeclothorwashedwitha clothdampenedina solution

ofwarmwaterand mildliquiddishwashingdetergent Rinsethoroughlyand wipe dry

° Never useharshcleaners,waz or polishonthecabinetfrent

• Besuretowringexcesswaterfromtheclothbeforewipingaround thecontrols Excess

waterinor around thecontrolsmay causedamagetotheairconditioner

• Pluginairconditioner

Winter Storage

If you planto storethe air conditioner duringthe winter,remove it carefullyfrom the

window according tothe installationinstructionsCoveritwith plasticor returnitto the

originalcarton.

Energy Saving ideas

• Do not blockair flow Insidewith blinds,curtains orfurniture; or outsidewith shrubs,

enclosures, or other buildings

• Thecapacityoftheroomairconditionermustfitthe roomsizeforefficientandsatisfactory

operation

Installthe roomairconditionerontheshadysideofyourhome Awindowthatfacesnorth

isbestbecauseitisshadedmostoftheday

• Closethefireplacedamper,floorand wall registersso coolair does notescapeup the

chimneyand intotheductwork

• Keapblindsanddrapasinotherwindowsclosedduringthesunniastpartoftheday

• Cleantheairfilterasrecommendedinthecection"CareandCleaning."

• Properinsulationand weatherstrippinginyourhomewillhelpkaspwarmair outand ccol

airin.

• Externalhouseshadingwithtreas,plantsorawningswillhelproducetheairconditioner's

work load.

• Operate heat producingappliancessuchas ranges,washers,dryersand dishwashers

duringthecoolestpartoftheday.

Avoid Service Checklist

Beforecallingfor service,reviewthis list.It may save youtimeand expense.Thislist

includescommonoccurrencesthat are not the resultof defectiveworkman-shipor

materialsin thisappliance.

OCCURRENCE SOLUTION

Air conditioner wM not operate.

Airfrom unitdoea notfealcold

enough.

Wailplugdisconnected.Pushplugfirmlyintowalloutlet.

PlugCurrentDeviceTripped.Pressthe RESETbutton.

Housefuseblownor circuitbreakertripped.Replacefusewithtimedelaytypeor resetoimuitbreaker.

Con_'olisOFF. TurnControlON and settodesiredsetting.

Roomtemperaturebelow60°F (16°C).Coolingmaynotoccuruntilroomtemperaturerisesabove60°F (16°C).

Temperaturesensing elementtouchingcoldcoil,locatedbehindair tilter.Straightenaway fromceil.

Resetto a Lowertemperature.

Compressorshut-offby changingmodes.Waitapproximately3 minutesand listenfur compressorto res_ad

whensetin theCOOL mode.

Air conditioner cooling, but room is

too warm - iceforming on cooling

coil behinddecorative front.

Outdoortemperaturebelow80°F (18°C). Todefrost theceil, set FANONLY Mode.

Airfiltermaybe dirty.Cleanfilter.Referto Careand Cleaningsection. Todefrost,setto FANONLYMode.

Temperatureisse_ttooLowfornight-timecooling.Todefrosttheceil, set toFANONLY Mode.Then, setTem-

peraturetoa Highersetting.

Air conditioner cooling, but room is

too warm - NO Ice forming on

coonng coil behind decorative front.

Dirtyairtilter- air restricted.Cleanairfilter. Referto Careand Cleaningsection.

Temperatureisset tooHigh.Set temperaturetoa Lowersetting.

Air directionallouverspositionedimproperly.Positionlouversforbetterairdistribution.

Frontofunitisblockedbydrapes,blinds,furniture,etc. - restrictsairdistribution.Clearblockageinfrontofunit.

Doors,windows,registers,etc. open-coldairescapes.Closedoors,windows,registers,etc.

Unitrecentlyturnedoninhot room.Allowadditionaltimetoremove=storedheat"from walls,ceiling, floorand

furniture.

Air conditioner turns on end off

rapidly.

Dirtyairtilter- air restricted.Cleanair filter.

Outsidetemperatureextremelyhot. Set FANspeed to a fastersetdng to bringair past coolingceils more

frequently.

Noise when unit is cooling.

Air movementsound.Thisis normal.Iftoo loud,setto aslowerFANsetting.

Windowvibration-poorinstallation.Referto installationinstructionsor checkwithinstaller.

Water dripping iNSiDE when unit is Improperinstallation.Tiltair conditionerslightlyto the outsideto allowwater drainage.Refer to installation

cooling, instructions- checkwithinstaller.

Water dripping OUTSIDE when unit Unitremovinglargequantityofmoisture from humidroom.Thisisnormalduringexcessivelyhumiddays.

is cooling.

Remote Sensing Deactivating Remotecontrolnotlocatedwithinrange.Placeremotecontrolwithin20feet &180°, radiusofthefrontof the

Prematurely (Some Models). unit.

Room Too Cold.

Remotecontrolsignalobstructed.Removeobstruction.

Settemperature too low.Increaseset temperature.

Remote Sensingactivated(on somemodels)and remotecontrollocatedin Hot Spot- Relocateremote

controlor deactivateremotesensing.

if These Solutions Fag, Caii 1-800-444-4944 For Frigidaire Service.

Frigidaire FAM156R1A15 Owner's manual

Frigidaire FAM156R1A15 Owner's manual

Frigidaire FAM156R1A15 Owner's manual

Related papers

Other documents