Frigidaire FAH125N2T2 User manual

Brand: Frigidaire

Model: FAH125N2T2

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

66121613

USE & CARE MANUAL

ELECTRONIC CONTROL

AIR CONDITIONER

READ AND SAVE THESE INSTRUCTIONS

P/N 66121613

2 Warranty

3 Product Registration

3 Normal Sounds

4 Important Safety Instructions

5-9 Air Conditioner Features

10 Care and Cleaning

10 Energy Saving Ideas

11 Avoid Service Checklist

Contents

3 Packaging

NOTE: This USE & CARE MANUAL pro-

vides specific operating instructions for your

model. Use the room air conditioner only

as instructed in this USE & CARE MANUAL.

These instructions are not meant to cover

every possible condition and situation that

may occur. Common sense and caution

must be practiced when installing, operat-

ing, and maintaining any appliance.

SLIDER CASEMENT

ROOM AIR CONDITIONER WARRANTY

Your product is protected by this warranty

Your appliance is warranted by Electrolux. Electrolux has authorized Frigidaire Consumer Services and their authorized servicers to perform service under this

warranty. Electrolux authorizes no one else to change or add to any of these obligations under this warranty. Any obligations for service and parts under this

warranty must be performed by Frigidaire Consumer Services or an authorized Frigidaire servicer.

This warranty applies only to products in ordinary household use, and the consumer is responsible for the items

listed below.

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance

with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections

or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are

not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow

the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary

household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by persons other than authorized Frigidaire servicers; use of parts other than

Frigidaire Genuine Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse,

misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty

period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written

warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this

warranty must be obtained by following these steps, in order:

1. Contact Frigidaire Consumer Services or an authorized Frigidaire servicer.

2. If there is a question as to where to obtain service, contact our Consumer Relations Department at:

Frigidaire

P.O. Box 212378

Augusta, GA 30917

800-444-4944

Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by

Electrolux.

This warranty applies only in the 50 states of the U.S.A., Puerto Rico and Canada.

FOR SERVICE CALL 1-800-444-4944.

* NORMAL

RESPONSIBILITIES OF

THE CONSUMER

EXCLUSIONS

IF YOU NEED SERVICE

CANADA

Electrolux Canada Group

6150 McLaughlin Road

Mississauga, Ontario L5R 4C2

1-866-213-9397

6. Damage to unit after removal from packaging carton.

FULL ONE-YEAR

WARRANTY

LIMITED 2-5 YEAR

WARRANTY (Sealed

System)

THE CONSUMER WILL BE RESPONSIBLE

FOR:

Costs of service calls that are listed under

NORMAL RESPONSIBILITIES OF THE

CONSUMER.*

Diagnostic costs and any removal,

transportation and reinstallation costs which

are required because of service. Costs for

labor, parts and transportation other than with

respect to the Sealed Refrigeration System.

WARRANTY

PERIOD

One year from original

purchase date.

Second through fifth

years from original

purchase date.

FRIGIDAIRE, THROUGH ITS

AUTHORIZED SERVICERS, WILL:

Pay all costs for repairing or replacing parts

of this appliance which prove to be defective

in materials or workmanship.

Repair or replace any parts in the Sealed

Refrigeration System (compressor,

condenser, evaporator and tubing) proves to

be defective in materials or workmanship.

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the serial

plate is located on the outside of the cabinet.

Model No.

Serial No.

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed

and returned to the Frigidaire Company.

Vibration

Unit may vibrate and make noise

because of poor wall or window

construction or incorrect installation.

High Pitched Chatter

Today’s high efficiency compressors

may have a high pitched chatter

during the cooling cycle.

Sound of Rushing Air

At the front of the unit, you may

hear the sound of rushing air

being moved by the fan.

Gurgle/Hiss

“Gurgling or hissing” noise may be heard

due to refrigerant passing through

evaporator during normal operation.

Pinging or Swishing

Droplets of water hitting condenser

during normal operation may cause

“pinging or swishing” sounds.

Product Registration

Normal Sounds

Packaging

Remove all packaging from inside the unit, also any inserts placed into

the side louvers.

PACKAGING INSERTS

Avoid fire hazard or electric

shock. Do not use an extension cord or an

adaptor plug. Do not remove any prong from

the power cord.

Grounding type wall

receptacle

Do not, under any

circumstances, cut,

remove, or bypass the

grounding prong.

Power supply cord

with 3-prong grounding

plug and current

detection device

Read all instructions before using this air conditioner.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance. Read product labels for flammability and other warnings.

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,

follow basic precautions, including the following:

• Be sure the electrical service is adequate for the model you have chosen. This information

can be found on the serial plate, which is located on the side of the cabinet and behind the

grille.

• If the air conditioner is to be installed in a window, you will probably want to clean both

sides of the glass first. If the window is a triple-track type with a screen panel included,

remove the screen completely before installation.

• Be sure the air conditioner has been securely and correctly installed according to the

separate installation instructions provided with this manual. Save this manual and the

installation instructions for possible future use in removing or reinstalling this unit.

• When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front

and rear coils.

Electrical Information

The complete electrical rating of your new room air conditioner is stated on the serial plate.

Refer to the rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,

proper grounding is important. The power cord is equipped with a three-prong grounding

plug for protection against shock hazards.

• Your air conditioner must be used in a properly grounded wall receptacle. If the wall

receptacle you intend to use is not adequately grounded or protected by a time delay fuse

or circuit breaker, have a qualified electrician install the proper receptacle.

• Do not run air conditioner with outside protective cover in place. This could result in

mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter plug.

Important Safety

Instructions

The power supply cord with

this air conditioner contains a current

detection device designed to reduce the risk

of fire.

Please refer to the section ‘Operation of

Current Device’ for details.

In the event that the power supply cord is

damaged, it cannot be repaired it must be

replaced with a cord from the Product

Manufacturer.

Operation of Current

Device

The power supply cord contains a current device that senses damage to the power cord. To

test your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button.

You will notice a click as the RESET button pops out.

3. Press the RESET button. Again you will notice a click as the button engages.

4. The power supply cord is now supplying electricity to the unit. (On some products this is

also indicated by a light on the plug head).

NOTES:

• Do not use this device to turn the unit on or off.

• Always make sure the RESET button is pushed in for correct operation.

• The power supply cord must be replaced if it fails to reset when either the TEST button is

pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.

• If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one

obtained from the product manufacturer.

Plug in &

press RESET

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

NOTE: Some plugs have

buttons on the top.

Air Conditioner Features

TOUCH PAD

ELECTRONIC CONTROL OPERATING INSTRUCTIONS

Before you begin, thoroughly familiarize yourself with the control panel and remote as shown

below and all its functions, then follow the symbol for the functions you desire. The unit can

be controlled by the touch pad alone or with the remote.

NOTE: The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

YOU WILL SEE:TO TURN UNIT ON:

DO THIS:

PRESS ON/OFF

BUTTON

Exhaust

Open

Closed

SETS MODE

ADJUSTS

TEMPERATURE

TIME

SETS FAN

SPEEDS

DISPLAYS

TEMPERATURE/TIME

CHECK FILTER

RESET BUTTON

TURNS UNIT

ON OR OFF

ACTIVATES

TIMER

SETS MODE

EXHAUST SELECTOR

Auto

Temp

LIGHT

ON/OFF

REMOTE CONTROL

ACTIVATE

TIMER

FAN

SPEED

SETS

MODE

ADJUSTS

TEMP &

TIME

SETS

Note:

Tap or hold either up( ) or down( ) button until the desired

Note:

Fan speed starts at high and adjusts to a slower speed as

the room temperature dictates. For example, if the room doesn't

get too warm it will stay at the slowest speed. If the room

temperature rises quickly, such as a door being opened, it will

automatically go to the highest speed. The fan speeds will readjust

back to the slowest speed as the room returns to the original set

temperature. Press the Fan Speed button to adjust the fan speed

manually.

temperature is seen on the display. This temperature will be

automatically maintained anywhere between 60

F(16

C) and 90

(32

C). If you want the display to read the actual room temperature.

See "To Operate on Fan Only" section on Page 6.

The chosen fan speed LED will light up.

Air Conditioner Features

(continued)

TEMPERATURE SETTING:

TO ADJUST FAN SPEEDS:

TO USE AUTO TEMP FEATURE:

TO CHANGE

PRESS TO LOWER

PRESS TO RAISE

DO THIS:

YOU WILL SEE:

Lo, Med or Hi

PRESS TO SELECT:

DO THIS:

AUTO TEMP

PRESS TO SELECT:

DO THIS:

LIGHT On

Air Conditioner Features

(continued)

TO OPERATE FAN ONLY:

TO USE THE ENERGY SAVER FEATURE:

SLEEP FEATURE:

YOU WILL SEE:

DO THIS:

PRESS

CHOOSE

MODE BUTTON

FAN ONLY

DO THIS:

PRESS

CHOOSE

MODE BUTTON

ENERGY SAVER

Note:

Use this function only when cooling is not desired, such as

Note:

In this mode, the fan will continue to run for 3 minutes after

the compressor shuts off. The fan then cycles on for 2 minutes at

10 minute intervals until the room temperature is above the set

temperature, at which time the unit turns back on.

Note:

In this "MODE" the selected temperature will increase by 2

degrees F 30 minutes after the mode is selected. The temperature

will then increase by another 2 degrees F after an additional 30

minutes. This new temperature will be maintained for 7 hours

before it returns to the originally selected temperature. This ends

the "Sleep" MODE and the unit will continue to operate as originally

programmed. The "Sleep" MODE program can be cancelled at

any time during operation by pressing "Sleep" MODE button.

for room air circulation or to exhaust stale air (Remember to open

the vent during this function, but keep it closed during cooling for

maximum cooling efficiency). You can choose any fan speed you

prefer.

During this function, the display will show the actual room

temperature, not the set temperature as in the cooling mode.

YOU WILL SEE:

LIGHT On

YOU WILL SEE:

LIGHT On

SLEEP BUTTON

PRESS

DO THIS:

Air Conditioner Features

TIMER: DELAY STOP/START FEATURE:

CHECK FILTER FEATURE:

(continued)

YOU WILL SEE HOW MUCH TIME IS CHOSEN:

LIGHT On

YOU WILL SEE:

LIGHT On

DO THIS:

THEN DO THIS:

PRESS TIMER

BUTTON

PRESS UP ( ) OR

DOWN ( ) BUTTON

Note: For Delay Stop, the unit must be in the On position.

Note: For Delay Start, the unit must be in the Off position.

To adjust timer setting, tap or hold the UP arrow( ) DOWN arrow( )

to change delay timer at .5 hour increments, up to 10 hours, then

at 1 hour increments up to 24 hours. The control will count down

the time remaining until start (8, 7.5, 7, etc.). The Delay Start mode

automatically selects cooling with maximum Fan Speed. The

temperature maintained will be the same as previously set. To

change the set temperature, press “ COOL” then Up or Down

arrows until the desired temperature is indicated on the display.

After 5 seconds, the control will automatically change the display

back to the hours remaining until the unit will start/stop. Turning

the unit “ON” or “OFF” at any time will cancel the Delay Start/

Stop function.

The Delay Start/Stop Feature will work until the unit either starts

or stops. Once that happens the above steps have to be repeated

again.

Note: This feature is a reminder to clean the Air Filter (See Care

and Cleaning) for more efficient operation and cooling. The LED

(light) will illuminate after 250 hours of operation. To reset after

cleaning the filter, press the “ Check Filter ” button and the light

will go off.

FAULT CODES

If the display reads “AS”, a sensor

has failed. Contact yourAuthorized

Frigidaire Service Center

If the display reads “ES”, a sensor

has failed. Contact yourAuthorized

Frigidaire Service Center

Air Conditioner Features

(continued)

ADDITIONAL THINGS YOU SHOULD KNOW

fan will continue to run during this time.

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

The “Cool” circuit has an automatic 3 minute delayed start if the unit is turned off and on

quickly.this prevents overheating of the compressor and possible circuit breaker tripping. The

The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.

The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the

other and back, press and hold the “TEMP/TIMER” Up ( ) and Down ( ) buttons together for 3 seconds.

EXHAUST CONTROL

This Exhaust Control allows the air conditioner to either recirculate inside air (CLOSED) or exhaust air to the outside (OPEN).

The CLOSED position is used when maximum cooling is desired. It may also be used for air recirculation without cooling

when the air conditioner is set in any FAN position.

The OPEN position removes stale air from the room and exhausts it to the outside. Fresh air is drawn in through normal

passages in the home.

4-WAY LOUVERS

The 4-Way air directional louvers allow you to direct air flow

up or down, left or right throughout the room as needed.

closed

Exhaust

TO TURN UNIT OFF:

YOU WILL SEE:

DO THIS:

PRESS ON/OFF

BUTTON

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit

before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is necessary.

Trapped particles in the filter can build up and cause an accumulation of frost on

the cooling coils.

• Grasp the filter by the center and pull up and out.

• Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly.

Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing.

• Or, instead of washing you may vacuum the filter clean.

Cabinet Cleaning

• Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and

front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution

of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.

• Never use harsh cleaners, wax or polish on the cabinet front.

• Be sure to wring excess water from the cloth before wiping around the controls. Excess

water in or around the controls may cause damage to the air conditioner.

• Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from the window

according to the installation instructions. Cover it with plastic or return it to the original

carton.

NOTE: To prevent rust or electrical connections from being damaged, store air

conditioner in an upright position and a dry place.

Care and Cleaning

The capacity of the room air conditioner must fit the room size for efficient and satisfactory

operation.

Install the room air conditioner on the shady side of your home. A window that faces north

is best because it is shaded most of the day.

Close the fireplace damper, floor and wall registers so cool air does not escape up the

chimney and into the duct work.

Keep blinds and drapes in other windows closed during the sunniest part of the day.

Clean the air filter as recommended in the section “Care and Cleaning.”

Proper insulation and water stripping in your home will help keep warm air out and cool

air in.

External house shading with trees, plants or awnings will help reduce the air conditioner’s

work load.

Operate heat producing appliances such as ranges, washers, dryers and dishwashers

during the coolest part of the day.

Energy Saving Ideas

Do not block air flow inside with blinds,curtains or furniture;or outside with shrubs,

enclosures,or other buildings.

Air conditioner will not operate.

Air from unit does not feel cold

enough.

Air conditioner cooling, but room is

too warm - ice forming on cooling

coil behind decorative front.

Air conditioner cooling, but room is

too warm - NO ice forming on

cooling coil behind decorative front.

Air conditioner turns on and off

rapidly.

Noise when unit is cooling.

Water dripping INSIDE when unit is

cooling.

Water dripping OUTSIDE when unit

is cooling.

Room Too Cold.

Avoid Service Checklist

Before calling for service, review this list. It may save you time and expense. This list

includes common occurrences that are not the result of defective workman-ship or

materials in this appliance.

OCCURRENCE SOLUTION

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn Control ON and set to desired setting.

Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above 60°F (16°C).

Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.

Reset to a Lower temperature.

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart

when set in the COOL mode.

Outdoor temperature below 60°F (18°C). To defrost the coil, set FAN ONLY Mode.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY Mode.

Temperature is set too Low for night-time cooling. To defrost the coil, set to FAN ONLY Mode. Then, set Tem-

perature to a Higher setting.

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too High. Set temperature to a Lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit.

Doors, windows, registers, etc. open - cold air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling, floor and

furniture.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air past cooling coils more

frequently.

Air movement sound. This is normal. If too loud, set to a slower FAN setting.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to installation

instructions - check with installer.

Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.

Set temperature too low. Increase set temperature.

If These Solutions Fail, Call 1-800-444-4944 For Frigidaire Service.

Frigidaire FAH125N2T2 User manual

Brand: Frigidaire

Model: FAH125N2T2

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

66121613

Download PDF

report

Frigidaire FAH125N2T2 User manual

This manual is also suitable for

Frigidaire FAH125N2T2 User manual

Related papers

Other documents