PAC SBK929GB User manual

PAC
Brand
PAC
Model
SBK929GB
Type
User manual

This manual is also suitable for

PAC BKSBK929GB is a mounting kit that allows you to install an aftermarket radio into your Subaru vehicle. It is compatible with 2016 Foresters, 2015-16 Imprezas, 2016 WRXs, and 2015-16 XV Crosstreks. The kit includes all the necessary hardware to install the radio, including brackets, screws, and a pocket. It also includes instructions on how to remove the factory radio and install the aftermarket radio.

Here are some of the features and possible use cases of the PAC BKSBK929GB:

  • Allows you to install an aftermarket radio into your Subaru vehicle
  • Includes all the necessary hardware to install the radio

PAC BKSBK929GB is a mounting kit that allows you to install an aftermarket radio into your Subaru vehicle. It is compatible with 2016 Foresters, 2015-16 Imprezas, 2016 WRXs, and 2015-16 XV Crosstreks. The kit includes all the necessary hardware to install the radio, including brackets, screws, and a pocket. It also includes instructions on how to remove the factory radio and install the aftermarket radio.

Here are some of the features and possible use cases of the PAC BKSBK929GB:

  • Allows you to install an aftermarket radio into your Subaru vehicle
  • Includes all the necessary hardware to install the radio
iSBK929GB
VEHICLE APPLICATION
Subaru
2016 FORESTER
2015-16 IMPREZA
2016 WRX
2015-16 XV CROSSTREK
www.aampglobal.com www.aius.net
2500 East Francis Street Ontario, CA 91761, U.S.A.
Sales: (800) 477-2267
Intl: (727) 572-9255
Support: 888-228-5560
©2016 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 7/16 PRINT Ver. 7/16
SBK929GB Mounting Kit
DASH DISASSEMBLY INSTRUCTIONS
WARNING: Some OEM radio harnesses have very little slack and can be damaged when the OEM radio
is removed. Remove radio and harnesses with caution.
1. Remove (1) #10 Phillips head screw located on the small panel located to the bottom
right of the steering wheel. Remove Panel.
2. From the area on the driver side now exposed remove (1) 10mm bolt from the OEM
radio bracket, located below the radio in the center of the dash. You will need a socket
extension to reach the bolt.
3. Lower the glove box and remove.
4. From the area on the passenger side now exposed remove (1) 10mm bolt from the
OEM radio bracket, located below the radio in the center of the dash. You will need a
socket extension to reach the bolt.
5. Some models will have OEM climate control cables that will need to be released before
the radio/climate control panel can be removed.
6. Using a soft tool unsnap panel above the radio that includes the air vents and hazard
button. Unplug harnesses and remove.
7. From the are now exposed, remove (2) 10mm bolts from the OEM radio bracket
8. Gently unsnap and remove dash trim bezel, that includes the radio and climate controls.
9. Carefully Remove the factory radio and disconnect all wire harnesses.
2
3
DOUBLE DIN INSTALLATION INSTRUCTIONS
Figure A
KIT ASSEMBLY INSTRUCTIONS
Single ISO Mount Application
1. Remove the OEM climate controls from the factory bezel/radio brackets.
2. Install OEM climate controls into the SBK929GB mainframe using the bottom 2 screw
3. Insert pocket into lower section of the brackets and snap into rear pocket support tabs.
4. Install brackets to rear of main frame using the (6) screws provided.
5. Finish mounting the OEM climate controls along with the SBK929GB bracket supports
using the remaining (2) Phillips head screws.
6. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of
radio using screws provided with radio when possible, or screws supplied with kit.
7. Using the main frame of the as a guide, slide radio forward or backward for desired
look and then tighten screws to the radio.
Note: Attach a rear support bracket to the rear of the new radio and adjust as necessary to support
the weight of the radio. Suggested
Double DIN ISO Mount Application
See Fig B for bracket tab removal.
1. Remove the OEM climate controls from the factory bezel/radio brackets.
2. Install OEM climate controls into the SBK929GB mainframe using the bottom
2 screws only
3. See Fig B for removal of rear pocket support tabs.
4. Install brackets to rear of main frame using the (6) screws provided.
5. Finish mounting the OEM climate controls along with the SBK929GB bracket supports
using the remaining (2) Phillips head screws.
6. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of
radio using screws provided with radio when possible, or screws supplied with kit.
7. Using the main frame of the as a guide, slide radio forward or backward for desired
look and then tighten screws to the radio.
Note: Attach a rear support bracket to the rear of the new radio and adjust asnecessary to support
the weight of the radio. Suggested
Figure B
Remove shaded tabs
on left and right sides
of the brackets
(Right side not shown)
  • Page 1 1
  • Page 2 2

PAC SBK929GB User manual

PAC
Brand
PAC
Model
SBK929GB
Type
User manual
This manual is also suitable for

PAC BKSBK929GB is a mounting kit that allows you to install an aftermarket radio into your Subaru vehicle. It is compatible with 2016 Foresters, 2015-16 Imprezas, 2016 WRXs, and 2015-16 XV Crosstreks. The kit includes all the necessary hardware to install the radio, including brackets, screws, and a pocket. It also includes instructions on how to remove the factory radio and install the aftermarket radio.

Here are some of the features and possible use cases of the PAC BKSBK929GB:

  • Allows you to install an aftermarket radio into your Subaru vehicle
  • Includes all the necessary hardware to install the radio
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents