PAC BKHONK854D Operating instructions

PAC
Brand
PAC
Model
BKHONK854D
Type
Operating instructions

This manual is also suitable for

PAC BKHONK854D is a mounting kit designed to facilitate the installation of a double DIN or single ISO mount radio into select Honda and Acura vehicles. It includes brackets, screws, and other necessary hardware to securely mount the new radio in place of the factory unit.

The kit is compatible with 2008-2012 Honda Accord models equipped with OEM navigation and 2010-2012 Acura Crosstour models also equipped with OEM navigation.

With the PAC BKHONK854D, users can seamlessly integrate an aftermarket radio into their vehicle while maintaining the factory look and functionality.

PAC BKHONK854D is a mounting kit designed to facilitate the installation of a double DIN or single ISO mount radio into select Honda and Acura vehicles. It includes brackets, screws, and other necessary hardware to securely mount the new radio in place of the factory unit.

The kit is compatible with 2008-2012 Honda Accord models equipped with OEM navigation and 2010-2012 Acura Crosstour models also equipped with OEM navigation.

With the PAC BKHONK854D, users can seamlessly integrate an aftermarket radio into their vehicle while maintaining the factory look and functionality.

iHONK854D/L
www.aampglobal.com www.aius.net
2500 East Francis Street Ontario, CA 91761, U.S.A.
Sales: (800) 477-2267
Intl: (727) 572-9255
Support: 888-228-5560
VEHICLE APPLICATION
Honda
2008-12 ACCORD (with OEM Navigation)
2010-12 CROSSTOUR (with OEM Navigation)
©2018 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 6/18 PRINT Ver. 6/18
HONK854D/ HONK854L Mounting Kit
DASH DISASSEMBLY INSTRUCTIONS
1. Using a soft tool unsnap and remove the panel located in the center dash
left of the radio.
2. Using a soft tool unsnap and remove the panel located in the right side of the dash
above the glove box.
3. From the area now exposed, Remove (2) Phillips screws from the radio.
4. Using a soft tool unsnap and remove the air vents located in the center dash
above the radio
5. Using a soft tool unsnap and remove the panel located in the console that
includes the cup holders.
6. From the area now exposed, Remove (2) Phillips screws from the lower center dash.
Remove (2) Phillips screws from the top of the pocket. Remove OEM pocket.
7. Remove (2) Phillips screws from the OEM navigation disc drive. Remove
8. From the area now exposed, Remove (2) Phillips screws facing up from the
bottom of the OEM radio.
9. Using a soft tool unsnap and remove the radio with climate control panel.
Unplug all harnesses ,along with the radio and antenna connections
2
3
DOUBLE DIN INSTALLATION INSTRUCTIONS
Figure A
KIT ASSEMBLY INSTRUCTIONS
Single ISO Mount Application
1. Insert pocket into lower section of the HONK854 brackets
2. Install brackets to rear of main frame using the (4) screws provided.
3. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible, or screws supplied with kit.
4. Using the main frame of the HONK854 as a guide, slide radio forward or backward
for desired look and then tighten screws to the radio.
NOTE: Using the screws removed from the bottom of the OEM radio brackets
securely mount the HONK854 brackets to the sub-dash. Suggested.
Double DIN ISO Mount Application
See Fig B for bracket tab removal.
1. Remove pocket support tabs of the HONK854 brackets
2. Install brackets to rear of main frame using the (4) screws provided.
3. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible, or screws supplied with kit.
4. Using the main frame of the HONK854 as a guide, slide radio forward or backward
for desired look and then tighten screws to the radio.
NOTE: Using the screws removed from the bottom of the OEM radio brackets
securely mount the HONK854 brackets to the sub-dash. Suggested.
Figure B
Remove shaded tabs
on left and right sides
of the brackets
(Right side not shown)
MAIN FRAME PREPARATION
1. Unscrew (4) Phillips screws from both climate control button assembly
and then remove from the OEM radio panel
2. Reinstall the climate control button assemblies to the HONK854 mainframe using (6)
of the screws left over the disassembly, Do not screw the bottom inside location of
each climate control, as they will be used later during the radio bracket installation.
3. Remove (2) plastic clips from the OEM radio and reinstall to the lower posts on the
HONK854 mainframe.
  • Page 1 1
  • Page 2 2

PAC BKHONK854D Operating instructions

PAC
Brand
PAC
Model
BKHONK854D
Type
Operating instructions
This manual is also suitable for

PAC BKHONK854D is a mounting kit designed to facilitate the installation of a double DIN or single ISO mount radio into select Honda and Acura vehicles. It includes brackets, screws, and other necessary hardware to securely mount the new radio in place of the factory unit.

The kit is compatible with 2008-2012 Honda Accord models equipped with OEM navigation and 2010-2012 Acura Crosstour models also equipped with OEM navigation.

With the PAC BKHONK854D, users can seamlessly integrate an aftermarket radio into their vehicle while maintaining the factory look and functionality.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents