PurTest 77701 User manual

Brand
PurTest
Model
77701
Type
User manual

PurTest 77701

PurTest 77701 is a lead test kit that can detect dissolved lead at levels below the EPA action level of 15 parts per billion (ppb). It is a screening test that can be used to give you an idea of the lead levels in your water. The test is easy to use and takes only 10 minutes to complete.

To use the test, simply collect a water sample in the provided vial and add a few drops to the test strip. Wait 10 minutes and then compare the color of the lines on the test strip to the color chart on the package. If the right line is darker than the left line, or if both lines are equally dark, then your water may contain lead at a toxic level.

PurTest 77701

PurTest 77701 is a lead test kit that can detect dissolved lead at levels below the EPA action level of 15 parts per billion (ppb). It is a screening test that can be used to give you an idea of the lead levels in your water. The test is easy to use and takes only 10 minutes to complete.

To use the test, simply collect a water sample in the provided vial and add a few drops to the test strip. Wait 10 minutes and then compare the color of the lines on the test strip to the color chart on the package. If the right line is darker than the left line, or if both lines are equally dark, then your water may contain lead at a toxic level.

PurTest
®
Lead Test
The PurTest® Lead Test can detect dissolved
lead at levels below the EPA action level of
15 parts per billion (ppb).
1. Keep tests out of the reach of children and pets. Do not
ingest anything from this test kit. Do not drink water sample
used for testing. Store and use at room temperature (60-86 F).
2. Do not open packets or vial until you are ready to perform
the tests.
3. Do not use on hot water or water containing bleach
detergents.
4. Do not re-use any part of the test kit.
5. Read and follow all instructions carefully.
Instructions:
1. Open foil packet and take out all contents. The test contains
(1) Lead test strip, (1) sample vial and (1) dropper pipette,
as well as a desiccant packet (to be discarded).
2. Using dropper pipette, place water sample in the test vial.
To pick up sample, tightly squeeze the bulb at the end of the
pipette and place the open end into water sample. Release
the bulb to pick up sample. Use only (1) pipette full of water.
Swirl vial gently for several seconds. Place vial on a flat
surface.
3. Place the test strip into test vial, with arrows pointing down.
4. Wait (10) minutes. Do not disturb strip or vial during this
time. Blue lines will appear on the strip.
5. Take the strip out of vial and read results:
NEGATIVE: The LEFT line (next to number 1) is darker than
the RIGHT line (next to number 2).
If you only see the LEFT line (next to number 1), the
test is negative.
POSITIVE: The RIGHT line (next to number 2) is darker than
the LEFT line (next to number 1), or lines are equally dark
(Both LEFT and RIGHT lines are equally dark).
6. Note: If no lines appear or both lines are very light, the test
did not run properly and the result is not valid. If a test
strip shows a positive result, your water sample may
contain lead at a toxic level.
Note: If your water test outside the desired values, call
the Safe Drinking Water Hotline at 800-438-1942 or
call PurTest at 800-788-4825 for free advice.
Please note that PurTest® is a screening test and cannot be
used to certify water as safe or unsafe for drinking. PurTest®
provides approximate results ONLY when used in
strict accordance with instructions. American Water Service LLC
expressly disclaims any liability resulting from the use of this
product, failure to follow instructions or reliance of test results.
American Water Service LLC
www.purtest.com
email: [email protected]
P1203 318
Before You Begin....
American Water Service LLC
www.purtest.com
email: [email protected]
  • Page 1 1

PurTest 77701 User manual

Brand
PurTest
Model
77701
Type
User manual

PurTest 77701

PurTest 77701 is a lead test kit that can detect dissolved lead at levels below the EPA action level of 15 parts per billion (ppb). It is a screening test that can be used to give you an idea of the lead levels in your water. The test is easy to use and takes only 10 minutes to complete.

To use the test, simply collect a water sample in the provided vial and add a few drops to the test strip. Wait 10 minutes and then compare the color of the lines on the test strip to the color chart on the package. If the right line is darker than the left line, or if both lines are equally dark, then your water may contain lead at a toxic level.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents