Rotator Rod RRCC Installation guide

Brand: Rotator Rod

Model: RRCC

Type: Installation guide

Rotator Rod RRCC: Experience Effortless Shower Curtain Rotation and Easy Reach

With the Rotator Rod RRCC, you'll enjoy a hassle-free shower experience like never before. This innovative shower rod system features smooth rod rotation, allowing you to effortlessly open and close your shower curtain with just a gentle push. It's perfect for individuals with limited mobility or those seeking a more convenient bathing solution.

The Rod Reacher provides an extended reach for effortless rod rotation, eliminating the need to stretch or strain. Installation is a breeze with the included wall mounts, screws, and anchors, and the clear instructions guide you through each step.

Rotator Rod RRCC: Experience Effortless Shower Curtain Rotation and Easy Reach

Step 2: Sliding the Rod Together

Step 1: Attaching the Wall Mounts

Enjoy our 1 year warranty

Wall Mounts

Center the Wall Mount over

the tub’s edge with the closed

end toward the ceiling. Place

the center of the Wall Mount

at your desired rod height (at

least 75 inches from the floor

for a standard 72” curtain).

* NOTE : If, for any reason you wish to remove your Rotator Rod simply insert a flat-head screw driver between the Rotator Disk and the Wall Mount and give it a twist. It

will pop right out!

Screw Holes

Mark the top and bottom holes with a pencil.

Use a standard Phillips head screwdriver to

firmly press the tip of a white anchor into the

marked position. Next, with continued

pressure, screw the anchor until flush with

drywall - not recessed. Insert screws through

wall mount and into anchors.

Step 3: Snapping Your Rod in Place

Snap in Rod

Once the Wall Mounts are in position, take the rod you just twisted firmly together, remove the plastic and slide the

Cap and Ball out of the way.

Snap the Rotator Disks into place by firmly sliding its center point up the groove on the Wall Mount until it ‘clicks’

into place. Be sure the arrow on the Rotator Disk points down while snapping into place. Repeat on the other side.

EASY TIP The Rod Inserts slide in and out of the rod on either side to adjust the length of the Rotator Rod to fit

your bathroom walls.

Step 4: Securing the Ball and Cap

Caps

Accent Balls

Slide each Accent Ball to the end of the rod so the arrow on the

Rotator Disk is ponting in the direction of the Set Screw in the indent

of the Accent Ball. That is, toward the inside curve of the rod.

There are grooves inside the Accent Ball allowing it to slide over the

Rod Pins and snuggle up to the Wall Mounts. Tighten the clear Set

Screw in the top of the Ball using a small flat-head screw driver.

Caps

Finally, slide each Cap over its

end of the rod against the wall

and twist until it locks into the

Wall Mount

Wall

Mounts

x 2

Caps x 2

Accent Balls x 2

Pins + o-rings x 4

Rod Inserts +

Rotator Disks x 2

Rod Reacher provides an easy reach

for smooth rod rotation.

Hardware Packet

with 4 screws

and 4 anchors

Thank You for Your

Rotator Rod Purchase!

Here are your instructions for drywall installation. For mounting on

tile/stone/fiberglass without drilling check out our No-Drill Adapters!

www.RotatorRod.com

For questions, comments or support call 941-706-2272

CustomerService@RotatorRod.com

That’s it!

You’re ready to snap

your rod in place!

Tools you’ll need: pencil, tape measure, small flat-head screw driver, phillips-

head screw driver

Take a look at this great instructional video at http://tinyurl.com/nfbhex6

Align tract on Connector with

the dimple in the rod and press

together. Then twist in

opposite directions until

dimples align.

Rotator Rod RRCC Installation guide

Brand: Rotator Rod

Model: RRCC

Type: Installation guide

Rotator Rod RRCC: Experience Effortless Shower Curtain Rotation and Easy Reach

Download PDF

report

Rotator Rod RRCC Installation guide

Rotator Rod RRCC Installation guide

Other documents