ASSEMBLY AND INSTALLATION
INSTRUCTIONS
181115
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
C0209
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Hardware Package (included):
x
GU10 LED Max.7W (G)
(included)
Swivel
Light Head
Stem
Plastic Anchor (D)
Ceiling Support
Stem Bushing (I)
Wood Screw (E)
Canopy
Outlet Box
Set Screw
Mounting Screw (B)
Wire Connector (C)
Cross Bar (A)
Green Grounding
Screw
Cupule (F)
Cupule (F)
GU10 LED Bulb
Max.7W X6 (G)
Cross Bar (A)
Mounting Screw (B)
Wire Connector (C)
Plastic Anchor(D)
Wood Screw (E)
Turn off the power at fuse or circuit box
Installation Steps
1. Attach the cross bar (A) to the outlet box by using two mounting screws (B).
2. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections by using the wire
connector (C) as follows:
--- Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
--- Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power source.
--- Attach the fixture grounding wire to the cross bar (A) with the green grounding screw. Then connect it to the house
grounding wire with a wire connector (C).
Carefully put the wires back into the outlet box.
181115
Assembly Kit
6040AA (1SET)
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Cupule (F)
GU10 LED Bulb
Max.7W (G)
Cross Bar (A)
Mounting Screw (B)
Wire Connector (C)
Plastic Anchor(D)
Ceiling Support
Stem Bushing (H)
Wood Screw (E)
A: 8”
B: 82”
A
B
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.
This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided
that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof
of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty
does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed,
overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded
from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other
than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no
warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.
3. Attach the canopy to the cross bar (A) by aligning holes, secure the set screws from the side hole of the canopy
into the hole in the side of the cross bar (A).
4. Make two desired positions and drill holes on the ceiling for stem on the track.
5. Attach two plastic anchor (D) to the drilled positions, then attach wood screw (E) thread the ceiling support
stem bushing (H) to the plastic anchor (D) on the ceiling and twist the wood screw (E) to lock pins in place.
6. Attach the stem to the ceiling support stem bushing (H) by aligning holes, then twist the stem to lock pins in place.
7. Attach the cupule (F) to the top surface of the bulb lens. Insert the bulb (G) into the socket using the cupule (F). Twist
bulb to lock pins in place. Remove the cupule (F) from the bulb lens by pulling the knob of the cupule (F).
CautionLED Bulb, Type MR GU10 base, maximum 25W X 6
Halogen Bulb, Type MR GU10 base, maximum 35W X 6
Notes: LED Dimmable bulb to be compatible with most LED Dimmers, recommended Lutron:
MSCL-OP153MH, MACL-153MH, DVWCL-153PH, TGCL-153PH, SCL-153PH.
8. Adjust the light head to a desired position by using the swivel.
Turn on the power at fuse or circuit box
/
