Analog way Vertige User manual

Verge™

Ref. VRC300

USER MANUAL

Informaon contained in this document, in parcular data, pictures, informaon, trademarks and logos are exclusive

property of Analog Way and are protected by copyrights and other intellectual property rights.

Consequently, any representaon and/or reproducon, in part or in full, is prohibited and would be considered a

violaon of Analog Way’s copyright and other intellectual property rights.

Visual representaons (diagrams, photos, icons, pictograms, screenshots, spare parts, etc.) are not contractual.

Specicaons subject to change without prior noce.

THANK YOU

1. INTRODUCTION

2. HARDWARE INSTALLATION

3. THE VERTIGE™ FRONT PANEL

4. STARTING WITH THE VERTIGE™

2.1 Safety instrucons

3.1 Overview

3.2 Color codes

1.1 What is the Verge™

1.2 Useful terms and denions

2.2 Environmental specicaons

2.4 Unpacking and inspecon

2.3 Hardware specicaons

2.5 The Verge™ rear panel

4.1 System conguraon

4.2 User selecon

4.3 Show selecon

4.4 Iteraon selecon

4.5 Iteraon wizard

4.6 Assembly conguraon

4.7 Matrix conguraon

4.8 External device conguraon

4.9 Screen conguraon

4.10 Scene conguraon

4.11 Condence Screen conguraon

4.12 Monitoring conguraon

4.13 Source conguraon

4.14 Nave source conguraon

4.15 Stream image conguraon (before the event has started)

4.16 Stream image conguraon (during the event)

4.17 Preset Viewer

4.18 Preset management

4.19 Macro management

4.20 Sequence management

4.21 External controllers

4.22 Matrix library conguraon

4.23 External device library conguraon

5

6

13

15

6

13

14

15

16

17

19

21

29

35

36

39

40

41

43

44

45

46

50

47

52

48

52

54

5

11

12

By reading this manual you will be able to obtain the most from your powerful Verge™.

46

4

5.2 Source secon

5.2.1 Making live switching directly to Program

5.2.2 Switching between plugs on the device inputs

58

6. MECHANICAL DIAGRAM

7. WARRANTY

8. CONTACT INFORMATION

5.3 Preset secon

5.4 Control secon

5.5 Edit secon

5.6 Transion secon

5.7 Control transion secon

7.1 Warranty condions

7.2 Repair and return instrucons

7.3 Return condions

5.3.1 How to save a preset

5.3.2 How to load a preset

66

67

68

59

60

63

64

67

5. OPERATING THE VERTIGE™

5.1 Layer secon

5.1.1 Selecng layers from the touchscreen

5.1.2 Selecng layers from the front panel

5.1.3 Selecng layers on Program vs Preview

5.1.4 Using the layer selecon modier keys

56

5

1.1 What is the Verge™

1. INTRODUCTION

Verge™ is a revoluonary Remote Controller integrang new ways to create and manage large events and

mul-venues. The Verge™ brings a simple and exible approach to show creaon and management. Verge™

can control several screens and devices such as Ascender 48 - 4K - PL, Ascender 32 - 4K - PL, Ascender 16 -

4K, SmartMatriX Ultra, NeXtage 16 - 4K or NeXtage 08 - 4K systems, independently or simultaneously in any

kind of combinaon, including So Edge Blending. Verge™ also supports linked LiveCore™ devices (addive

modularity), LiveCore™ Expansion modules and synchronized LiveCore™ devices (associave modularity).

SHOW: a “Show” is a complete setup for an event containing several devices, screens, sources and presets.

ITERATION: an “Iteraon” is a version of a show. Iteraons can be used to create backups or variants of a

show. On a broader level, iteraons allow rening your setup step by step.

ASSEMBLY: an “Assembly” handles one or several idencal devices that can operate on the same screens.

Verge™ can handle several assemblies.

SCREEN: A “Screen” is a desnaon where a picture will be displayed. For example, it could be a single display

or a projecon surface composed of one or several outputs. Each screen might use one or several layers.

SCENE: A “Scene” is a virtual canvas dened in regions, and each region is processed by a Screen. Grouping

screens in scenes allows opmal use of LiveCore™ devices.

CONFIDENCE SCREEN: A “Condence Screen” is a desnaon (single display or more) usually dedicated to

the speaker/presenter, which can display the content visible to the audience and more.

PRESET: a “Preset” on the Verge™, is a capture of a state of the event (one or more scenes). Preset allows

storing the layout of the elements and their sources for a specic step of the event.

LAYER: a “Layer” is an image display element (such as a Background, a PIP, or a Logo) that has an associated

visual priority — either in front of another layer or behind.

PIP: a “PIP” refers to Picture-in-Picture. It is a layer, typically not full size, which displays a stream on top

of another layer. PIPs can be reduced, enlarged, bordered and shadowed. They can overlap one another,

depending on their visual priority.

STREAM: a “Stream” can be Live (signal from an input plug) or Sll (frame/logo) and allows you to display

content with various sengs (aspect rao, brightness, crop…) in a layer.

SOURCE: a “Source” allows the user to assign a Verge™ front panel key to a stream (per screen).

FRAME: a “Frame” is an image, usually used to ll a background, which is selected from the sll Frame library.

It can be loaded to a LiveCore™ device using the Web RCS.

LOGO: a “Logo” is a small image, usually used to display company logo or labels, which is selected from the

sll Logo library. It can be loaded to a LiveCore™ device using the Web RCS.

SOFT EDGE: So Edge blending technology is used to compensate overlapping video projectors displaying

content on a surface. The resulng image will appear as though it were a single unied picture.

HARD EDGE: Hard Edge technology is used to display connuous content using several outputs without any

overlap. The outputs are “side by side”, they don’t overlap or share pixel informaon. (Opposed to So Edge

where some parts of the image are sent simultaneously to several displays).

MATRIX ROUTER: A “Matrix router” is a device allowing to route video signals to mulple desnaons on

demand. It provides a 1-1 (router) or a 1-n (router & splier) distribuon. With the Verge™, it will extend

the total number of streams available to several LiveCore™ devices.

1.1 What is the Verge™

1.2 Useful terms and denions

6

2.1 Safety instrucons

2. HARDWARE INSTALLATION

For opmal use of this device, read all safety and operang instrucons before use. Keep the safety and

operang instrucons for future reference. Please follow all of the warnings on this product and its operang

instrucons.

• WARNING: To prevent the risk of electric shock and re, do not expose this device to rain, humidity or

intense heat sources (such as heaters and direct sunlight). Slots and openings in the device are provided for

venlaon and to avoid overheang. Make sure the device is never placed near a texle surface that could

block the openings. Also keep away from excessive dust, vibraons and shocks.

• POWER: Only use the power supply indicated on the device of the power source. Devices equipped with

a grounding plug should only be used with a grounding type outlet. In no way should this grounding be

modied, avoided or suppressed. Connecon of equipment to main supply must be aer branch circuit

breaker of the building installaon.

• POWER CORD: The device is equipped with a detachable power cord. To remove mains, switch o the

device and disconnect the power cord at appliance coupler.

Cauon: The power cords constute the only mean to completely disconnect the equipment from the main

power. To make sure the device is not supplied, these two cords must be unplugged from the mains

outlet.

Use the following guidelines:

- The equipment connected to the network must have a release system easily accessible and located

outside the unit.

- Unplug both power cords; do not pull on the power cords but always on the plug itself.

- The outlets should always be near the device and easily accessible.

- Power supply cords should be routed so that they are not likely to be walked on or pinched by items

placed on or against them.

If one of the power supply cords is damaged, unplug the device. Using the device with a damaged power

supply cord may expose your device to electric shocks or other hazards. Verify the condion of the power

supply cords periodically. Contact your dealer or service center for replacement if damaged.

• CONNECTIONS: All inputs and outputs (except for the power input) are Safety Extra Low Voltage (SELV)

circuits as dened in UL/IEC 60950-1.

• SERVICING: Do not aempt to service this product yourself by opening or removing covers and screws

since it may expose your device to electric shocks or other hazards. Refer all problems to qualied service

personnel.

• OPENINGS: Never push objects of any kind into this product through the openings. If liquids have been

spilled or objects have fallen into the device, unplug it immediately and have it checked by a qualied

technician.

2.1 Safety instrucons

2.1.1 English

7

2.1 Safety instrucons

Pour une ulisaon opmale de cet appareil, nous vous conseillons de bien lire toutes les consignes de sécurité

et de fonconnement avant ulisaon. Conservez les instrucons de sécurité et de fonconnement an de

pouvoir les consulter ultérieurement. Respectez toutes les consignes marquées dans la documentaon, sur le

produit et sur ce document.

• ATTENTION : An de prévenir tout risque de choc électrique et d’incendie, ne pas exposer cet appareil à la

pluie, à l’humidité ou à des sources de chaleur intense.

• INSTALLATION : Veillez à assurer une circulaon d’air susante pour éviter toute surchaue à l’intérieur de

l’appareil. Ne placez pas l’appareil sur ou à proximité d’une surface texle suscepble d’obstruer les orices de

venlaon. N’installez pas l’appareil à proximité de sources de chaleur comme un radiateur ou une poche d’air

chaud, ni dans un endroit exposé au rayonnement solaire direct, à des poussières excessives, à des vibraons

ou à des chocs mécaniques. Ceci pourrait provoquer un mauvais fonconnement et un accident.

• ALIMENTATION : Ne faire fonconner l’appareil qu’avec la source d’alimentaon indiquée sur l’appareil.

Les appareils doivent être obligatoirement connectés sur une source équipée d’une mise à la terre ecace.

En aucun cas cee liaison de terre ne devra être modiée, contournée ou supprimée. Raccordement des

équipements à l’alimentaon principale doit être postérieur au disjoncteur de branchement de l’installaon

électrique du bâment.

• CORDON D’ALIMENTATION : Les appareils sont équipés d’un cordon d’alimentaon détachable. La mise

hors tension se fait sur appareil éteint en débranchant ce cordon de l’appareil.

Aenon : Les appareils sont équipés de 2 cordons d’alimentaon détachable, la mise hors tension se fait en

débranchant ces cordons de l’appareil.

Appliquer les consignes suivantes :

- Le matériel relié à demeure au réseau, doit avoir un disposif de seconnement facilement accessible

qui doit être incorporé à l’extérieur de l’appareil.

- Débrancher les 2 cordons d’alimentaon de la prise murale si vous prévoyez de ne pas uliser l’appareil

pendant quelques jours ou plus.

- Pour débrancher les cordons, rez-les par la che. Ne rez jamais sur les cordons proprement dit.

- Les prises d’alimentaon doivent se trouver à proximité de l’appareil et être aisément accessibles.

- Ne laissez pas tomber les cordons d’alimentaon et ne posez pas d’objets lourds dessus.

Si un des 2 cordons d’alimentaon est endommagé, débranchez-le immédiatement de la prise murale. Il est

dangereux de faire fonconner un appareil avec un cordon endommagé ; un câble abîmé peut provoquer

un risque d’incendie ou un choc électrique. Vériez les câbles d’alimentaon de temps en temps. Contactez

votre revendeur ou le service après-vente pour un remplacement.

• CONNEXIONS : Toutes les entrées et sores (exceptée l’entrée d’alimentaon) sont des circuits de très

basse tension de sécurité (TBTS) tels que dénis dans UL / IEC 60950-1.

• RÉPARATION ET MAINTENANCE : L’ulisateur ne doit en aucun cas essayer de procéder aux opéraons de

dépannage, car l’ouverture des appareils par retrait des capots ou de toutes autres pièces constuant les

boîers ainsi que le dévissage des vis apparentes à l’extérieur, risquent d’exposer l’ulisateur à des chocs

électriques ou autres dangers. Contactez le service après-vente, votre revendeur ou adressez-vous à un

personnel qualié uniquement.

• OUVERTURES ET ORIFICES : Les appareils peuvent comporter des ouvertures (aéraon, fentes, etc...),

veuillez ne jamais y introduire d’objets et ne jamais obstruer ses ouvertures. Si un liquide ou un objet

pénètre à l’intérieur de l’appareil, débranchez immédiatement l’appareil et faites-le contrôler par un

personnel qualié avant de le remere en service.

2.1.2 French

8

2.1 Safety instrucons

Per un ulizzo omale dell’apparecchio, leggere tue le istruzioni di sicurezza e di ulizzo prima dell’uso.

Conservare le istruzioni di sicurezza e di funzionamento al ne di poterle consultare ulteriormente. Seguire

tu i consigli indica su questo manuale e sull’apparecchiatura.

• ATTENZIONE: Al ne di prevenire qualsiasi rischio di shock elerico e d’incendio, non esporre l’apparecchiatura

a pioggia, umidità e a sorgen di eccessivo calore.

• INSTALLAZIONE: Assicuratevi che vi sia una suciente circolazione d’aria per evitare qualsiasi

surriscaldamento all’interno dell’apparecchiatura. Non collocare l’apparecchiatura in prossimità o su

superci tessili suscebili di ostruire il funzionamento della venlazione. Non installate l’apparecchiatura

in prossimità di sorgen di calore come un radiatore o una fuoruscita d’aria calda, né in un posto esposto

direamente ai raggi del sole, a polvere eccessiva, a vibrazioni o a shock meccanici. Ció potrebbe provocare

un erroneo funzionamento e un incidente.

• ALIMENTAZIONE: Far funzionare l’apparecchiatura solo con la sorgente d’alimentazione indicata

sull’apparecchiatura. Le apparecchiature queste devono essere obbligatoriamente collegate su una sorgente

fornita di una eciente messa a terra. In nessun caso questo collegamento potrà essere modicato, sostuito

o eliminato. Connessione delle apparecchiature alla rete elerica deve essere successiva interruore di

circuito dell’impianto dell’edicio

• CAVO DI ALIMENTAZIONE: Questo apparecchio e’ equipaggiato con un cavo di alimentazione. Per rimuoverlo,

spegnete l’apparecchio e disconneere il cavo di alimentazione dalla presa di corrente.

Aenzione: i cavi di alimentazione sono l’unico di disconneere l’apparecchio all’alimentazione. Per assicurarsi

che l’apparecchio e totalmente scollegato, i cavi devono essere disconessi della presa murale.

Seguire le instruzioni seguen:

- Il materiale collegato a residenza alla rete, deve avere un disposivo di sezionamento facile da

raggiungere e che deve essere inserito all’esterno del apparecchio.

- Scollegare l’apparecchiatura dalla presa a muro se si prevede di non ulizzarla per qualche giorno.

- Per disconneere il cavo, rare facendo forza sul conneore.

- La prese d’alimentazione deve trovarsi a prossimità dell’apparecchiatura ed essere facilmente

accessibile.

- Non far cadere il cavo di alimentazione né appoggiarci sopra degli ogge pesan. Se il cavo di

alimentazione é danneggiato, spegnere immediatamente l’apparecchiatura.

E’ pericoloso far funzionare questa apparecchiatura con cavi di alimentazione danneggia, cavi graa

possono provocare un rischio di incendio o uno shock elerico. Vericare spesso i cavi di alimentazione.

Contaare il vostro rivenditore o il servizio assistenza per una sostuzione.

• CONNESSIONE: Tu gli ingressi e le uscite (tranne che per la potenza in ingresso) sono bassissima tensione

di sicurezza (SELV) circui deni UL / IEC 60950-1.

• RIPARAZIONI E ASSISTENZA: L’ulizzatore non deve in nessun caso cercare di riparare l’apparecchiatura,

poiché con l’apertura del coperchio metallico o di qualsiasi altro pezzo costuente la scatola metallica,

nonché svitare le vi che appaiono esteriormente, poiché ció puó provocare all’ulizzatore un rischio di

shock elerico o altri rischi.

• APERTURE DI VENTILAZIONE: Le apparecchiature possono comportare delle aperture di venlazione, si

prega di non introdurre mai ogge o ostruire le sue fessure. Se un liquido o un oggeo penetra all’interno

dell’apparecchiatura, disconneerla e farla controllare da personale qualicato prima di rimeerla in

servizio.

2.1.3 Italian

9

2.1 Safety instrucons

Zum opmalen Gebrauch dieses Gerätes lesen Sie bie vorher alle Sicherheits- und Bedienhinweise.

Diese Sicherheits- und Betriebsanweisungen für einen späteren Gebrauch sicher auewahren. Alle in den

Unterlagen, an dem Gerät und hier angegebenen Sicherheitsanweisungen einhalten.

• ACHTUNG: um jegliches Risiko eines Stromschlags oder Feuers zu vermeiden, das Gerät nicht Regen,

Feuchgkeit oder intensiven Wärmequellen aussetzen.

• EINBAU: Eine ausreichende Luzufuhr sicherstellen, um jegliche Überhitzung im Gerät zu vermeiden. Das

Gerät nicht auf und in Nähe von Texloberächen, die Belüungsönungen verschließen können, aufstellen.

Das Gerät nicht in Nähe von Wärmequellen, wie z.B. Heizkörper oder Warmlukappe, aufstellen und es

nicht dem direkten Sonnenlicht, übermäßigem Staub, Vibraonen oder mechanischen Stößen aussetzen.

Dies kann zu Betriebsstörungen und Unfällen führen.

• STROMVERSORGUNG: Das Gerät nur mit der auf dem Gerät bezeichnete Stromquelle betreiben. Gerät mit

geerdeter Hauptstromversorgung muss an eine Stromquelle mit ezienter Erdung angeschlossen werden.

Diese Erdung darf auf keinen Fall geändert, umgangen oder enernt werden. Anschluss von Geräten ans

Stromnetz muss nach Abzweigschalter des Gebäudes Installaon

• NETZKABEL: Das Gerät ist mit einem enernbaren Netzkabel ausgestaet. Um das Gerät vollständig vom

Netz zu trennen, schalten Sie es aus und ziehen Sie das Netzkabel ab.

Achtung: Das Netzkabel stellt die einzige Möglichkeit dar, das Gerät vollständig vom Netzanschluss zu trennen.

Um sicherzustellen, dass das Gerät nicht mehr versorgt wird, muss dieses Kabel aus der Netzsteckdose

ausgesteckt werden.

Bie beachten Sie die folgenden Hinweise:

- Wenn Geräte dauerha am Netz bleiben, müssen sie über eine leicht zugängliche Trennvorrichtung

verfügen, die außen am Gerät angebracht sein muss.

- Das Kabel miels des Steckers herausziehen. Niemals am Stromkabel selbst ziehen.

- Die Steckdose muss sich in der Nähe des Geräts benden und leicht zugänglich sein.

- Das Stromkabel nicht fallen lassen und keine schweren Gegenstände darauf stellen.

Wenn eines der beiden Stromkabel beschädigt ist, das Gerät sofort abschalten. Es ist gefährlich, das Gerät mit

einem beschädigten Stromkabel zu betreiben; ein abgenutztes Kabel kann zu einem Feuer oder Stromschlag

führen. Die Stromkabel regelmäßig untersuchen. Für Ersatz wenden Sie sich an Ihren Verkäufer oder eine

Kundendienststelle.

• ANSCHLÜSSE: Alle Eingänge und Ausgänge (mit Ausnahme der Stromversorgung) sind Safety Extra Low

Voltage (SELV) Schaltungen wie in UL / IEC 60950-1 deniert.

• REPARATUR UND WARTUNG: Der Benutzer darf keinesfalls versuchen das Gerät selbst zu reparieren, die

Önung des Geräts durch Abnahme der Abdeckhaube oder jeglichen anderen Teils des Gehäusessowie die

Enernung von außen sichT-baren Schrauben zu Stromschlägen oder anderen Gefahren für den Benutzer

führen kann. Wenden Sie sich an Ihren Verkäufer, Ihre Kundendienststelle oder an qualizierte Fachkräe.

• ÖFFNUNGEN UND MUNDUNGEN: Die Geräte können über Önungen verfügen (Belüung, Schlitze, usw.).

Niemals Gegenstände in die Önungen einführen oder die Önungen verschließen. Wenn eine Flüssigkeit

oder ein Gegenstand in das Gerät gelangt, den Stecker herausziehen und es vor einer neuen Inbetriebnahme

von qualiziertem Fachpersonal überprüfen lassen.

2.1.4 German

10

2.1 Safety instrucons

Para un uso ópmo de este equipo, lea las instrucciones de seguridad y operación antes de ulizarlo. Conserve

las instrucciones de seguridad y de funcionamiento para que pueda consultarlas posteriormente. Respete

todas las consignas indicadas en la documentación, relacionadas con el producto y este documento.

• CUIDADO: Para prevenir cualquier riesgo de choque eléctrico y de incendio, no exponga este aparato a la

lluvia, a la humedad ni a fuentes de calorintensas.

• INSTALACIÓN: Cerciórese de que haya una circulación de aire suciente para evitar cualquier

sobrecalentamiento al interior del aparato. No coloque el aparato cerca ni sobre una supercie texl que

pudiera obstruir los oricios de venlación. No instale el aparato cerca de fuentes de calor como radiador o

boca de aire caliente, ni en un lugar expuesto a los rayos solares directos o al polvo excesivo, a las vibraciones

o a los choques mecánicos. Esto podría provocar su mal funcionamiento o un accidente.

• ALIMENTACIÓN: Ponga a funcionar el aparato únicamente con la fuente de alimentación que se indica en

el aparato. Los aparatos deben estar conectados obligatoriamente a una fuente equipada con una puesta

a erra ecaz. Por ningún movo este enlace de erra deberá ser modicado, cambiado o suprimido.

Conexión del equipo a la red eléctrica debe ser posterior del interruptor de circuitos derivados de la

instalación del edicio

• CABLE DE CORRIENTE: El equipo se suministra con un cable de alimentación desmontable. Para desconectar

de la red eléctrica, apague primero el equipo y después, desconecte el cable de alimentación de la red

eléctrica.

Atención: Los cables de alimentación constuyen el único medio de desconectar el aparato totalmente de la

red eléctrica. Para estar seguro de que el aparato no está más alimentado, estos dos cables deben

estar desconectados de la toma de corriente.

Aplicar las siguientes consignas:

- El material conectado a residencia a la red informáca, debe de tener un disposivo de seccionamiento

fácilmente accesible que debe de ser incorporado al exterior del aparato.

- Desconectar el aparato del enchufe mural si no piensa ulizarlo durante varios días.

- Para desconectar los cables, re de la clavija. No re nunca de los cables propiamente dichos.

- El enchufes de alimentación debe estar cerca del aparato y ser de fácil acceso.

- No deje caer los cables de alimentación ni coloque objetos pesados encima de ellos.

Si uno de dos cables de alimentación sufriera algún daño, ponga el aparato inmediatamente fuera de tensión.

Es peligroso hacer funcionar este aparato con un cable averiado, ya que un cable dañado puede provocar un

incendio o un choque eléctrico. Verique el estado los cables de alimentación de vez en cuando. Póngase en

contacto con su distribuidor o con el servicio de posventa si necesita cambiarlo.

• CONEXIONES: Todas las entradas y salidas (a excepción de la entrada de alimentación) son de tensión extra

baja de seguridad (SELV) circuitos denidos en UL / IEC 60950-1.

• REPARACIÓN Y MANTENIMIENTO: Por ningún movo, el usuario deberá tratar de efectuar operaciones

de reparación, ya que si abre los aparatos rerando el capó o cualquier otra pieza que forma parte de las

cajas o si destornilla los tornillos aparentes exteriores, existe el riesgo de producirse una explosión,choques

eléctricos o cualquier otro incidente. Contacte el servicio de posventa, a su distribuidor o dirigirse con

personal cualicado únicamente.

• ABERTURAS Y ORIFICIOS: Los aparatos pueden contener aberturas (aireación, ranuras, etc.). Nointroduzca

allí ningún objeto ni obstruya nunca estas aberturas. Si un líquido o un objeto penetra al interior del aparato,

desconéctelo y hágalo revisar por personal cualicado antes de ponerlo nuevamente en servicio.

2.1.5 Spanish

11

2.2 Environmental specicaons

• Cooling air ows from front side to rear.

• Max ambient operang temperature: < 40°C (< 104°F).

• Operang temperature: 0 to +40°C / +32°F to +104°F

• Storage temperature: -40 to +70°C / -40°F to +158°F

• Operang humidity: 10 to 80% (non condensing)

• Input voltage range: 100-240 VAC autosensing, 50/60 Hz

• Typical consumpon: 225 W

ELECTRICAL SECURITY:

• IEC 60950-1:2005 (2nd Edion); Am 1:2009

• EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011, CSA C22.2; Naonal Dierences specied in the CB

Test Report

• ETL listed (Canada & US)

ELECTROMAGNETIC COMPATIBILITY:

• IEC 61000-3-2 (2009)

• IEC 61000-3-3 (2008)

• CISPR22 (2008)

• CISPR24 (2010)

• FCC Part15 of 2012

• IECS-003 of August 2012

ENVIRONMENT:

• RoHS

• WEEE

USE/TRANSPORT:

• ETS 300 019-2-2: Environmental condions and environmental tests for telecommunicaons equipment ;

Part 2-2 : specicaon of environmental tests ; Transportaon ; Specicaon T 2.3: Public transportaon

• ETS 300 019-2-3: Environmental condions and environmental tests for telecommunicaons equipment ;

Part 2-3 : specicaon of environmental tests ; Staonary use at weather protected locaons ; Specicaon

T 3.1 and T 3.1 E: Temperature-controlled locaons

2.2 Environmental specicaons

Should your device lose power unexpectedly, you will lose any unsaved sengs.

12

2.3 Hardware specicaons

2.4 Unpacking and inspecon

Dimensions:

 W 740 x D 510 x H 200 mm

 W 29.2” x D 20.0” x H 7.9”

Weight:

 15 kg / 33 lbs

Shipping Weight:

 20 kg / 44 lbs

Electrical Requirements:

Required Voltage: 100-240 VAC

Required Amperage: 2.5A between the two power supplies

• 1 x Verge™ (VRC300) remote controller

• 2 x Power supply cords

• 1 x User manual (PDF version)*

• 1 x Quick start guide*

* The User manual and the Quick start guide are available on www.analogway.com

2.5 The Verge™ rear panel

2

1 3

1. Power Supply: Dual, redundant power supply with fuse as standard equipment.

2. On/O buon: Switch on/o the device.

3. Connecon Panel: Ethernet LAN adapters to control devices.

IMPORTANT: Audio and RS232 connectors are reserved for Factory use only.

13

3.1 Overview

3. THE VERTIGE™ FRONT PANEL

3.1 Overview

1- Touch screen

2- Preset secon

3- Layer secon

4- Source secon

5- Control secon

The touch screen 15’’6 Wide displays comfortably on the same page the representaon of the Program &

Preview of a typical scene (Blend + 2 satellites). It is important to have the whole scene represented to work

on mulple layers from dierent screens at the same me (change of source of background, for example). It

is useful to have both states Program/Preview shown at the same me as the LiveCore™ series allows you to

change one or the other at any me (even during an eect).

This secon allows the user to save/load its scene

presets (10 direct access presets and a page

mechanism to organize them).

This secon enables the operator to select a set

of layers which belong to dierent scenes in order

to edit them simultaneously. Various criteria are

used to perform advanced combinaons. It will be

possible to save those combinaons for later use.

This secon allows assigning sources to the selected

layers in Program or Preview. Twelve contextual

buons display the name of sources. The page

mechanism allows beneng from numerous

sources.

This secon enables the operator

to select which preset to work with,

and have direct access to basic

funcons applied to all selected

layers (Freeze, Clear, Unify ...).

1

2

3

4

8

7

5

6

14

3.2 Color codes

7- Transion secon

8- Control Transion

6- Edit secon

This secon enables the operator to use the T-Bar

and sliders for transions. Sliders allow individual

scene mixing. They are motorized in order to see

the current state of the selecon.

The CUE SEQUENCE buon is used to switch the Control Transion secon to CUE SEQUENCE mode in order

to control the cue sequence playback.

Note: The ALPHA buon is unused in this Firmware version.

The Verge™ buons were designed with a handy color code to guide users, avoid mistakes, and give a

constant status of the device. Thus, all Verge™ buons have two or three dierent states (and colors),

depending on their funcon and their current state.

All standard buons mapped to an available funcon/slot light up GREEN.

All contextual buons mapped to an available funcon/slot light up BLUE.

Any of these buons turns YELLOW when the funcon/slot is selected/lled.

If one of these buons blinks YELLOW, it means the funcon/slot is waing for a conrmaon (a second

consecuve press).

All double sized buons like PROGRAM or PREVIEW are either OFF or lighten up in RED to indicate the

current mode.

TAKE CUT & TAKE buons are always RED and will BLINK when there is a Take in progress.

This secon allows the operator to edit the selected

layers in three dierent ways: roughly via the

joysck, nely via the encoders, or directly via the

numpad. With its 12 contextual LCD keys, the block

displaying the numpad (the EDIT pad) also provides

access to a variety of edit tools such as pages of

shortcuts, layer presets and macros.

3.2 Color codes

IMPORTANT: The front panel is available as soon as an iteraon is loaded. The front panel is

dedicated to presets and transions and the touch screen state will never interfere with it.

15

4.1 System conguraon

4. STARTING WITH THE VERTIGE™

4.1 System conguraon

When the Verge™ starts up, the Home page is automacally displayed. Press the START buon, then

press the Verge™ SETTINGS buon in the upper-right corner.

• Conguring the system me:

In the top bar, select the Time tab.

Change the system me accordingly, by

pressing the +/- buons. When ready,

press the Apply buon.

• Conguring the network:

In the top bar, select the Network tab.

Select the Ethernet port used by the

Verge™ on your network then enter

the corresponding IP address, subnet

mask and gateway. When ready, press

the Apply buon.

• Updang the rmware:

In the top bar, select the Firmware tab.

The upper area displays the current

rmware version. Make sure the USB

ash drive you are using contains an

up-to-date version of the Verge™

rmware. Plug this USB ash drive into

one of the Verge™ USB connectors.

Wait for the device to appear in the

Storage list then select it to display the

rmware updaters available. Select the

desired update from the list then press

the Update buon to start updang the

Verge™.

IMPORTANT: Do not remove the USB ash drive or turn o the power while updang.

16

4.2 User selecon

The User Selecon page allows you to login and manage user accounts:

• Creang a new user account:

In the le menu, select the CREATE

opon. Enter the user’s name. If this

user account needs to be password-

protected then enter the corresponding

password in the Password and Conrm

Password elds. When ready, press the

Create buon. You can also press the

Create & Login buon to create the user

account and log in automacally.

• Logging in:

In the le menu, select the LOGIN opon

then select an exisng user account. If

this user account is password-protected,

enter the corresponding password.

When ready press the Login buon to

log in and display the Show Selecon

page.

Note: There are two predened user accounts available: Admin and Guest. An Admin can only manage

other user accounts (reset password, delete an account…). A Guest cannot create any show; he is only

allowed to use shows that have been shared by other users (read only).

IMPORTANT: the password for the Admin account is “Password”.

• Enable Auto load at startup:

In the top bar, select the Auto Load tab.

Enable Auto load to automacally reload

the last session at startup (last User,

Show and Iteraon).

Note: Auto load only works for User

sessions without password. If the

last opened session was protected

by User password the Verge™

boots with default behavior.

17

4.3 Show selecon

The Show Selecon page allows you to manage shows for the currently logged-in user:

• Creang a new show:

In the le menu, select the CREATE

opon then enter the name of the show.

Check the Share box if you intend to

share this show with any other users

(read only). When ready, press the

Create buon. You can also press the

Create & Load buon to create the show

and load it automacally.

• Loading a show:

In the le menu, select the LOAD opon.

Select the show you want to load and

then press the Load buon to load this

show and display the Iteraon Selecon

page.

• Deleng a show:

In the le menu, select the DELETE opon. Select the show you want to delete and then press the Delete

buon to permanently erase this show.

4.4 Iteraon selecon

The Iteraon Selecon page allows you to manage iteraons (versions) for the current show.

Each show can have many iteraons, each represenng a branch or restore point of your conguraon. This

way you can use iteraons to create backups, variants, or step by step renements of a show.

For example, if you re-use a le from a previous show, you may wish to create a new iteraon as clone of the

previous one, and work within the new iteraon. This would allow you to make updates and changes to the

show, but sll allow you to use your previous version if necessary.

This acon cannot be undone.

Note: Creang a show will automacally create a default iteraon.

18

4.4 Iteraon selecon

• Creang a new iteraon:

In the le menu, select the CREATE

opon then enter a descripon for this

iteraon. When ready, press the Create

buon. You can also press the Create &

Load buon to create the iteraon and

load it automacally.

• Loading an iteraon:

In the le menu, select the LOAD opon.

Select the iteraon you want to load and

then press the Load buon to load this iteraon and begin working on your event setup.

• Copying an iteraon:

In the le menu, select the COPY opon. Select the iteraon you want to duplicate in the From eld. You can

oponally enter a descripon for this iteraon. When ready, press the Copy buon. You can also press the

Copy & Load buon to copy the iteraon and load it automacally.

• Deleng an iteraon:

In the le menu, select the DELETE opon. Select the iteraon you want to delete and then press the Delete

buon.

• Exporng an iteraon to a USB key:

In the le menu, select TRANSFER then

select the EXPORT opon. Select the

iteraon you want to export then plug a

USB ash drive into one of the Verge™

USB connectors. Select your USB ash

drive in the Storage list and press the

Export buon to start exporng this

iteraon.

This acon cannot be undone.

19

4.5 Iteraon Wizard

• Imporng an iteraon from a USB key:

In the le menu, select TRANSFER then select the IMPORT opon. Plug a USB ash drive into one of the

Verge™ USB connectors. Select your USB ash drive in the Storage list to display the iteraons available.

Select the iteraon you want to import then press the Import buon to start imporng it into the current

show (as a new iteraon index).

• Copying an iteraon from another

show:

In the le menu, select TRANSFER then

select the COPY FROM opon. Select the

show to copy from (one of your shows

or a show shared with you within the

Verge), and then one of its iteraons.

When ready, press the Copy buon to

copy the selected show iteraon as a

new iteraon of the current show.

4.5 Iteraon Wizard

The Iteraon Wizard allows you to quickly setup an iteraon and thus have a version of your show up and

running in just a few steps:

Wizard Step 1 (Assembly):

In the Device Type eld, select the type

of device that will be handled by this

assembly.

In the Device Extension eld, select the

Single opon if you have only one single

device to control in this assembly.

Select the Synchronized opon if two,

three or four idencal devices will

be synchronized for achieving bigger

screens (associave modularity). When

synchronized, all the sources must be

split and congured the same way on all

devices (frames and logos included).

Select the Linked with SLAVE opon, if the device is linked to another compliant device (addive modularity).

Select the Linked with LOE opon, if the device is linked to a LiveCore™ Output Expander (addive modularity).

If your device(s) have an opon (4K or 4K - PL), then make sure to select it in the Device Opon eld.

Note: All synchronized devices of an assembly must be idencal (you can try to manually downgrade a device

via the WebRCS to overcome this limitaon).

20

Wizard Step 2 (Devices):

Enter the IP address of the Master device.

If you have selected the Synchronized

opon, then check the Slave #X boxes

to enable up to three addional devices

that will be synchronized with the

Master device. Then adjust each device

IP address to match your network

conguraon. Press the Next buon to

connue.

Wizard Step 3 (Screens):

Select the total number of screens wired

to your devices.

Screens are added sequenally in

Grid mode. Select an item on the list

to rename or adjust it. If some of the

screens are used for a blend, adjust

their size accordingly. To freely combine

outputs into a specic screen pixel

space, change the mode to Custom

Canvas then adjust the canvas size and

the quanty of areas. If a screen must be

congured as a Condence screen then

check the Condence box (see chapter

4.11 Condence Screen conguraon).

Wizard Step 4 (Scenes):

Select how the Verge™ arranges the

Screens.

- Select Each Screen in a New Scene

(default) to use the Verge™ as in

previous versions. Each Screen is

encapsulated in its own Scene and

remains independent.

- Select All Screens in one New Scene

or All Screens in one Exisng Scene

for Advanced use. Screens are grouped

into a single Scene and work together to

achieve a bigger and / or more complex

visual state, with some constraints (see chapter 4.10 Scene conguraon).

4.5 Iteraon Wizard

The Condence opon and the chosen Grid/Custom Canvas mode cannot be edited once the

screen is created. This means that an exisng screen cannot be turned Condence, Grid or

Custom Canvas. You will have to delete the screen and then re-create it with the proper opon/

mode enabled.

The Verge™ does not allow access to the Screens directly. Instead, it allows access to Scenes,

which funcon as a virtual Canvas processed by Screens.

Page is loading ...

Analog way Vertige User manual

Analog way Vertige User manual

Related papers

Other documents