Zanussi ZFK22/10LP User manual

Brand: Zanussi

Model: ZFK22/10LP

Category: Fridge-freezers

Type: User manual

REFRIGERADOR

CONGELADOR

FRIDGE-FREEZER

ZFK 22/10 LP

LIBRO DE INSTRUCCIONES INSTRUCTION BOOKLET

2222 138-76

WARNINGS

General Safety

ª This appliance is designed to be operated by

adults. Children should not be allowed to tamper

with the controls or play with the product.

ª It is dangerous to alter the speciﬁcations or modify

this product in any way.

ª Care must be taken to ensure that the appliance

does not stand on the electrical supply cable.

ª Before any cleaning or maintenance work is

carried out, be sure to switch off and unplug the

appliance.

ª This appliance is heavy. Care should be taken

when moving it.

ª Ice lollies can cause frost burns if consumed

straight from the appliance.

Service / Repair

ª Any electrical work required to install this

appliance should be carried out by a qualiﬁed

electrician or competent person.

ª This product should be serviced by an authorized

Service Centre, and only genuine spare parts

should be used.

ª Under no circumstances should you attempt to

repair the appliance yourself.

Repairs carried out by inexperienced persons may

cause injury or more serious malfunctioning. Refer

to your local Service Centre, and always insist on

genuine spare parts.

Use

ª The domestic refrigerators and freezers are

designed to be used speciﬁcally for the storage of

edible foodstuffs only.

ª Frozen food must not be re-frozen once it has been

thawed out.

ª Manufacturers’ storage recommendations should

be strictly adhered to. Refer to relevant

instructions.

ª The inner lining of the appliance consists of

channels through which the refrigerant passes. If

these should be punctured this would damage the

appliance beyond repair and cause food loss.

DO NOT USE SHARP INSTRUMENTS to scrape

off frost or ice. Frost may be removed by using the

scraper provided. Under no circumstances should

solid ice be forced off the liner. Solid ice should be

allowed to thaw when defrosting the appliance.

See defrost instructions.

ª Do not place carbonated or ﬁzzy drinks in the

freezer as it creates pressure on the container,

which may cause it to explode, resulting in

damage to the appliance.

Installation

ª There are working parts in this product which heat

up. Always ensure that there is adequate

ventilation as a failure to do this will result in

component failure and possible food loss. See

installation instructions.

ª Parts which heat up should not be exposed.

Wherever possible the back of the product should

be against a wall.

ª If the appliance has been transported horizontally,

it is possible that the oil contained in the

compressor ﬂows in the refrigerant circuit. It is

advisable to wait at least two hours before

connecting the appliance to allow the oil to ﬂow

back in the compressor.

Environment Protection

ª This appliance does not contain gasses which

could damage the ozone layer, in either its

refrigerant circuit or insulation materials. The

appliance shall not be discarded together with

the urban refuse and rubbish. Avoid damaging

the cooling unit, especially at the rear near the

heat exchanger. Information on your local

disposal sites may be obtained from your

municipal authorities.

The materials used on this appliance marked

with the symbol are recyclable.

It is most important that this instruction book should be retained with the appliance for future reference.

Should the appliance be sold or transferred to another owner, or should you move house and leave the

appliance, always ensure that the book is supplied with the appliance in order that the new owner can be

acquainted with the functioning of the appliance and the relevant warnings.

These warnings are provided in the interest of safety. You must read them carefully before installing or

using the appliance.

Warning!

The appliance which you have just bought is supplied

not only with the instruction manual, but also with a

Warranty Card Certiﬁcate, on the back of which are

written the relative conditions.

Please ﬁll in the necessary details on the Card

Certiﬁcate and send it to the Zanussi Centre covering

the area in which the appliance is to be installed. (See

list of Zanussi network centres).

We congratulate you on your choice. Read this

instruction manual carefully and follow the

recommendations it provides to beneﬁt from years of

excellent service.

The appliance which you have just purchased has been

very accurately controlled throughout the entire

manufacturing process. Nevertheless, should any

problem arise during usage, whether it be during the

warranty period, or when such period has expired,

please contact your nearest Zanussi Service Centre

immediately.

The address and telephone number of this Centre can

be easily found in the enclosed List or by looking in the

telephone directory, under Zanussi.

Our Zanussi Service Network is at your complete

disposal, to serve you with maximum speed and

efﬁciency, all you have to do is call.

D223

595

600

1190

638

D488

Closed door

Appliance height:

Open door

1700 mm

CONTENTS

Installation 19

ª Location 19

ª Cleaning the interior 20

ª Door reversibility 21

ª Fitting door panels 21

Technical speciﬁcation 22

ª Electrical connection 22

Use 23

ª Control panel 23

ª Use of the freezer 23

ª Storing of frozen foods 23

ª Fast freezing 23

ª Warning light 23

ª Freezing of fresh foods 23

ª Storage of frozen food 24

ª Thawing 25

ª Ice cube trays 25

ª Use of the refrigerator 25

ª Operation 25

ª Air circulation 25

ª Fresh food refrigeration 26

ª Positioning the door shelves 27

ª Defrosting 28

Maintenance 29

ª Periodic cleaning 29

ª Idle periods 29

ª Interior light 29

Servicing 29

INSTALLATION

If this appliance featuring magnetic door seals is to

replace an older appliance having a spring lock on

the door or lid, be sure to make that spring lock

unusable before you discard the old appliance.

This will prevent it from becoming a death-trap

for a child.

Location

The appliance should be installed well away from

sources of heat such as radiators, boilers, direct

sunlight etc.

Best performance is obtained with ambient

temperature between +18°C and +43°C (class T);

+18°C and +38°C (class ST); +16°C and +32°C (class

N); +10°C and +32°C (class SN).

The class of your appliance is shown on its rating

plate.

Make sure that there is nothing at the back, at the top

and at the bottom of the appliance to obstruct air

circulation.

For more efﬁcient operation of the appliance the

minimum distance between the top of the appliance

and other overhanging kitchen furniture, if any,

should be at least 15 mm (Fig. 1-A).

The best solution is shown in Fig. 1-B (without

overhanging kitchen furniture).

The appliance sides may also be in contact with the

kitchen furniture, provided that air can circulate freely

round the back and top.

One or more adjustable feet mounted on the base of

the appliance make it possible to set it perfectly level.

Fig. 1

NP002

100 mm 10 mm

10 mm

Important

It is essential that the appliance be connected to an

efﬁcient earth tap. For this purpose the supply cable

plug incorporates a special earth contact. If the

sockets of your domestic wiring system are not

earthed, have the appliance connected to a separate

earth wire by a qualiﬁed electrician in accordance

with existing safety regulations.

The Manufacturer declines all responsibility if the

above safety precautions are not observed.

This appliance complies with EEC directive

number 87/308 of 2/6/87 relative to radio

interference suppression.

This appliance complies with the following

E.E.C. Directives:

- 73/23 EEC of 19.2.73 (Low Voltage Directive) and

subsequent modiﬁcations;

- 89/336 EEC of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent

modiﬁcations.

Cleaning the interior

Before using the appliance for the ﬁrst time, wash the

interior and all internal accessories with lukewarm

water and some neutral soap so as to remove the

typical smell of a brand-new product, then dry

thoroughly.

Do not use detergents or abrasive powders, as these

will damage the ﬁnish.

Door reversibility

Unplug the appliance from the power supply before

carrying out the below-mentioned operations.

Remove the ventilation grill (D).

Unscrew the bottom hinge (E).

Remove the freezer door by releasing it from the

middle hinge (H).

Unscrew the middle hinge.

Remove the fridge door by releasing it from the top

hinge pin (A).

Remove the pin and the washer (A+B) from the top

hinge (C), then mount these on the opposite side.

Reﬁt the fridge door.

Replace the middle hinge to the left hand side.

Replace the freezer door.

Screw down the bottom hinge (E) on the opposite side

by using the screws previously removed.

Detach the plug (F) from the ventilation grill (D). To

do this, press it in the direction of the arrow.

Introduce the plug (G), which is delivered with the

appliance, into the hole left free on the opposite side.

Re-assemble the ventilation grill (D).

Reverse the direction of the handle.

The holes which are not used are masked by plastic

plugs which should be removed and reﬁtted onto the

free holes.

The doors can be aligned by adjusting both the middle

and top hinges.

The middle hinge can be adjusted horizontally, with

the help of a tool, after having slackened the two

screws.

The top hinge is adjusted by slackening the nut with a

10 mm spanner and then proceeding as shown in the

Figure.

Fitting door panels

(for models equipped with door frame)

To ﬁt the door panel, proceed as follows:

Loosen the ﬁxing screws to remove the frame side

opposite the handle.

Loosen all the screws ﬁxing the door frames.

Insert the panel from the side on which the frame has

been removed and push it through. Reﬁt the frame to

the door.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

D071

D427

D426

D405

TECHNICAL SPECIFICATION

Electrical connection

Before plugging in, ensure that the voltage and

frequency shown on the serial number plate

correspond to your domestic power supply.

Voltage can vary by ±6% of the rated voltage.

For operation with different voltages, a suitably sized

auto-transformer must be used.

The technical data is indicated in the rating plate on the left side inside the appliance.

USE

USE OF THE FREEZER

The freezer is marked with the symbol,

which means that the compartment is suitable for

freezing fresh food and for long-term storage of

frozen food.

Storing of frozen foods

Insert the plug into the wall socket, pilot light (A) will

come on; this indicates that the appliance is switched

on.

Set the knob (D-Fig. 6) to a position between 1 and 6.

To safely store frozen and deep-frozen foods, the

temperature inside the freezer must be at least –18°C

or colder.

Therefore, we suggest you turn the knob (D) to a

medium setting.

The temperature inside the freezer is automatically

adjusted to ensure safe storage of the food.

However if the appliance works in unfavourable room

conditions such as poor ventilation, high or low

ambient temperature and frequent door openings, it

might be necessary to adjust the setting.

Turn knob (D) to the higher numbers to obtain lower

temperatures and, conversely, to the lower numbers if

a less cold temperature is required.

Freezer operation can be halted by turning knob (D)

to position «

O».

The refrigerator will continue to work.

Fast freezing

Turn the knob (E-Fig. 6) to «S» (SUPER) setting

(pilot light (B) comes on).

Warning light (C-Fig. 6)

This light warns when the temperature inside the

freezer compartment has increased to a point at which

safe storage of food can no longer be guaranteed.

When the appliance is switched on for the ﬁrst time or

when food is placed in the compartment for freezing,

this light remains on until the temperature has reached

the level required for correct storage.

Freezing of fresh foods

To fast-freeze foods when the appliance has not been

in use, switch on the freezer and let it run on the fast-

freeze setting for at least three hours before putting

the food to be frozen in the compartment.

If the appliance is already in operation, it should run

Control panel (Fig. 6)

Fig. 6

A - Freezer pilot light

B - SUPER operating control light

C - Temperature warning light

D - Freezer compartment thermostat knob

E - NORMAL/SUPER knob

F - Refrigerator compartment thermostat knob

G - Refrigerator pilot light

ABC F

on the fast-freeze setting for at least 24 hours before

the food is put in the freezer. Once the food has been

placed in the freezer, the freezing operation can be

considered to be complete 24 hours later.

Once freezing is complete, the freezer must be reset

for normal storage use.

Food to be frozen must be placed in the top

compartment.

The maximum amount of food which is freezable

in 24 hours is 16 kg.

To help you get the best out of the freezing process,

here are a few hints:

Freeze only good-quality, fresh and well-cleaned

foods.

Split them into small portions to speed up freezing

and to avoid having to thaw more food than you

require.

It is in fact important to remember that once food has

thawed out, it deteriorates fast.

Another point to remember is that lean foods keep

better and longer than fatty foods. Salt too reduces

storage time.

Wrap food in foil or polythene ﬁlm, ensuring that the

wrapping adheres closely to the food and is well

sealed.

In this way, by avoiding contact with air, the colour

ﬂavour and nutritional value of the food remains

intact.

Never freeze a higher quantity of food than the

maximum amount shown on the rating plate of the

appliance.

During the freezing process, do not add further food

for freezing and do not open the freezer door.

Food for freezing should not be placed in contact with

already frozen food. This will avoid the temperature

of already frozen food from rising.

Never put ﬁzzy drinks in the freezer as they might

well burst.

In addition, never put hot foods or liquids in the

freezer compartment and take care not to ﬁll

recipients up to the brim if they are covered with a lid.

It is a good idea to mark the packs – or the cards on

the sliding drawers if your model has them – with the

date on which foods were frozen so that you can keep

a check on storage periods.

If accidental thawing occurs – due to a power cut for

example – food must be used up very quickly or else

cooked immediately and refrozen. If, however, the

power failure is relatively brief (from 6 to 8 hours)

and the freezer compartment is packed full, frozen

food will not suffer any damage.

The inner door of the freezer compartment shows

pictures of different types of food followed by a

ﬁgure. These ﬁgures indicate the maximum storage

time, in months, for each type of food.

Details of food being stored, can also be written in

pencil on a card located in a special holder in the

inner door.

Storage of frozen food

When ﬁrst starting-up or after a period out of use, let

the appliance run for at least three hours on the fast

freeze setting before putting the products in the

compartment.

To obtain the best performance from this appliance,

you should:

if large quantities of food are to be stored, remove all

drawers and baskets from appliance and place food on

cooling shelves. Pay careful attention not to exceed

load limit stated on the side of the upper

section (where applicable).

make sure that the commercially frozen foodstuffs

were adequately stored by the retailer;

be sure that frozen foodstuffs are transferred from the

foodstore to the freezer in the shortest possible time;

not open the door frequently or leave it open longer

than absolutely necessary.

Once defrosted, food deteriorates rapidly and cannot

be refrozen.

Do not exceed the storage period indicated by the

food manufacturer.

Important

If there is a power failure when food is in the

freezer, do not open the door of the freezer

compartment. The frozen food will not be affected

if the power cut is of short duration (up to 6-8

hours) and the freezer compartment is full,

otherwise, it is recommended that the food should

be used within a short time (a temperature

increase of the frozen food shortens its safe storage

period).

Thawing

Before being used, deep-frozen and frozen food can

be thawed out either in the refrigerator or at room

temperature, depending on the time available for this

operation.

Small pieces of food, such as hamburgers, chips, and

ﬁsh ﬁngers, for example, can be cooked straight out of

the freezer, without any intermediate thawing

operation.

Clearly, cooking time will be marginally longer than

in the case of thawed food.

Ice cube trays

The freezer is provided with one or more ice cube

trays.

These trays should be ﬁlled with drinking water and

then placed in the freezer compartment.

Do not use metal tools to remove the trays when they

are stuck-frozen inside the compartment.

USE OF THE REFRIGERATOR

Operation

Turn the thermostat knob (F-Fig. 6) to a setting

between 2 and 4, which is usually the most

appropriate. However, the exact setting should be

chosen keeping in mind that the temperature inside

the refrigerator depends on:

room temperature;

how often the door is opened;

the quantity of food stored in the refrigerator;

location of appliance.

As in the case of the freezer, it might be necessary to

turn the knob to higher settings to obtain a lower

refrigeration temperature or, vice versa, to lower

settings to increase the refrigeration temperature.

To stop the fridge, set the thermostat knob to position

O». The freezer will continue to work.

Air circulation

Your appliance is ﬁtted with a fan inside the

refrigerator compartment. To tun it on, press the

switch (A-Fig. 7) located on the fan housing; the

switch will illuminate. To turn the fan off, press this

switch again; the switch light will go out.

The appliance can be operated with the fan turned off

(switch off/light out); in this case, remember to set the

thermostat knob between 4 and 6.

It is recommended that the fan be turned on (switch

on/illuminated) in the following circumstances:

high ambient temperature (above 25°C);

to obtain faster cooling (for example after having

placed a large quantity of food in the refrigerator;

to achieve a uniform temperature throughout the

refrigerator compartment.

Bear in mind that when the fan is operating, the

recommended position for the thermostat knob is

between 2 and 4.

It is also advisable not to turn the fan on if the

temperature inside the compartment is cool enough:

this will reduce energy consumption.

Fig. 7

D671

Fresh food refrigeration

To obtain the best performance:

do not store warm food or evaporating liquids in the

refrigerator;

do cover or wrap the food, particularly if it has a

strong ﬂavour.

Position food so that air can circulate freely round it.

Useful hints:

Meat (all types): wrap in polythene bags and place on

the glass shelf above the vegetable drawer.

For safety, store in this way only one or two days at

the most.

Cooked foods, cold dishes, etc..: these should be

covered and may be placed on any shelf.

Fruit and vegetables: these should be thoroughly

cleaned and placed in the special drawer(s) provided.

Butter and cheese: these should be placed in special

airtight containers or wrapped in aluminium foil or

polythene bags to exclude as much air as possible.

Milk bottles: these should have a cap and should be

stored in the bottle rack on the door.

Bananas, potatoes, onions and garlic, if not

packed, must not be kept in the refrigerator.

The walls of the refrigerator are equipped with a

series of runners so that the glass shelves can be

positioned as desired.

For better use of space, the front half-shelves can lie

over the rear ones.

Fig. 8

D338

Positioning the door shelves

To permit storage of food packages of various sizes,

the door shelves can be adjusted in height.

To make these adjustments proceed as follows:

Gradually pull the shelf in the direction of the arrows

until it comes free, then reposition as required

(Fig. 9).

For more thorough cleaning, the top door shelf can be

removed by pulling it in the direction of the arrows,

then reﬁtting it in position (Fig. 10).

Fig. 9

Fig. 10

D064

D066

Defrosting

Frost is automatically eliminated from the evaporator

of the refrigerator compartment every time the motor

compressor stops, during normal use. The defrost

water drains out through a trough (Fig. 11) into a

special container on the back of the appliance, where

it evaporates.

In the freezer compartment however, the frost should

be removed with the special plastic scraper provided,

whenever the thickness exceeds 4 mm.

During this operation it is not necessary to switch off

the power or to remove the foods from the

compartment.

Do not use sharp instruments to scrape off frost to

avoid damaging the appliance.

If a thick layer of ice is formed it will be necessary to

carry out complete defrosting as follows:

set the knob (D) to «

O» or unplug the appliance from

the mains socket;

wrap frozen food in several layers of newspaper and

place the food packages in a cool place.

Leave the door open. Insert the plastic scraper in the

appropriate seating, place a basin underneath to

collect the defrost water (Fig. 12).

After complete defrosting thoroughly dry the

refrigerator compartment.

Keep the scraper for future use.

Reconnect the appliance to the power supply, start it

up and, after two or three hours, replace the foods

previously removed from the freezer.

Important

Remember that an increase in the surface temperature

of already-frozen foods may signiﬁcantly decrease

their storage life.

We particularly recommend that you periodically

clean the defrost-water drainage hole, located in

the centre of the drainage groove in the

refrigerator compartment (Fig. 11) to prevent the

defrost water from overﬂowing onto foods stored

in the compartment. Use the special cleaner

provided, which you will ﬁnd already inserted into

the drainage hole.

Fig. 11

Fig. 12

D037

D068

MAINTENANCE

Unplug the appliance before carrying out any

maintenance operation.

Periodic cleaning

Wash the interior with lukewarm water and sodium

bicarbonate, and clean the painted components with

silicone wax; clean the condenser and the motor

compressor with a brush or a vacuum cleaner. This

operation will improve the operation of the appliance

and save energy.

Idle periods

During periods when the appliance is not used, you

should take the following precautions:

remove the plug from the wall socket;

remove all food from the appliance;

defrost and clean the interior and all accessories;

leave the door slightly open, thus letting air circulate

and preventing the formation of mould and unpleasant

smells.

Interior light

The light bulb inside the refrigerator compartment can

be reached as follows:

- unscrew the light cover securing screw,

- unhook the moving part as shown in the ﬁgure.

Fig. 13

D731

SERVICING

If the appliance is not functioning properly check that:

the plug is ﬁrmly in the wall socket and the mains

power switch is on;

there is no power failure; the control knob is in the

right position.

Furthermore:

if the appliance seems too noisy check that the sides

are not touching furniture that can transmit or amplify

noise or vibration. Also, check that the refrigerant unit

does not vibrate.

If there is water on the fridge bottom, make sure the

defrost water drainage hole is not clogged (Fig. 11).

If your appliance is still not working properly after

making the above checks, contact your local dealer or

the nearest service center.

To obtain fast service, it is essential that when you apply

for it you specify the model and serial number of your

appliance which can be found on the warranty

certiﬁcate or on the rating plate, on the bottom left side

of the refrigerator compartment.

Zanussi ZFK22/10LP User manual

Brand: Zanussi

Model: ZFK22/10LP

Category: Fridge-freezers

Type: User manual

Download PDF

report

Zanussi ZFK22/10LP User manual

Zanussi ZFK22/10LP User manual

Related papers

Other documents