ADTRAN TA 544 User manual

ADTRAN
Brand
ADTRAN
Model
TA 544
Category
Networking
Type
User manual

This manual is also suitable for

TA 544 User Manual/61200704L1-1A
Page 1 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
TA 544
User Manual
61200704L1-1A
May 2001
1200704L1 TA 544
4200704L3 TA 544 with SDSL Card
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 2 of 68
Trademarks
Any brand names and product names included in this manual are trademarks,
registered trademarks, or trade names of their respective holders.
Total Access is a registered trademark of ADTRAN, Inc.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN
reserves the right to change the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential
damages or for commercial losses even if ADTRAN has been advised thereof as a
result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
©2001 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
TA 544 User Manual/61200704L1-1A
Page 3 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
Safety Instructions
When using your telephone equipment, please follow these basic safety
precautions to reduce the risk of fire, electrical shock, or personal injury:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. To reduce risk of electric shock, do not disassemble this product. Opening or
removing covers may expose you to dangerous voltages or other risks.
Save These Important Safety Instructions
Notes provide additional useful information.
Caution signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.
To prevent electrical shock, do not install equipment in a wet location or during a lightning
storm.
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 4 of 68
Limited Product Warranty
ADTRAN warrants that for 5 years from the date of shipment to Customer, all
products manufactured by ADTRAN will be free from defects in materials and
workmanship. ADTRAN also warrants that products will conform to the
applicable specifications and drawings for such products, as contained in the
Product Manual or in ADTRAN's internal specifications and drawings for such
products (which may or may not be reflected in the Product Manual). This
warranty only applies if Customer gives ADTRAN written notice of defects during
the warranty period. Upon such notice, ADTRAN will, at its option, either repair
or replace the defective item. If ADTRAN is unable, in a reasonable time, to repair
or replace any equipment to a condition as warranted, Customer is entitled to a full
refund of the purchase price upon return of the equipment to ADTRAN. This
warranty applies only to the original purchaser and is not transferable without
ADTRAN's express written permission. This warranty becomes null and void if
Customer modifies or alters the equipment in any way, other than as specifically
authorized by ADTRAN.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE
FOREGOING CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF
THE CUSTOMER AND THE EXCLUSIVE LIABILITY OF ADTRAN AND IS
IN LIEU OF ANY AND ALL OTHER WARRANTIES (EXPRESSED OR
IMPLIED). ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER
WARRANTIES, INCLUDING (WITHOUT LIMITATION), ALL
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY NOT
APPLYTOCUSTOMER.
In no event will ADTRAN or its suppliers be liable to Customer for any incidental,
special, punitive, exemplary or consequential damages experienced by either
Customer or a third party (including, but not limited to, loss of data or information,
loss of profits, or loss of use). ADTRAN is not liable for damages for any cause
whatsoever (whether based in contract, tort, or otherwise) in excess of the amount
paid for the item. Some states do not allow the limitation or exclusion of liability
for incidental or consequential damages, so the above limitation or exclusion may
not apply to Customer.
TA 544 User Manual/61200704L1-1A
Page 5 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
International Contact Information
ADTRAN, Inc.
Attention: International Department
901 Explorer Boulevard
Huntsville, Alabama 35806
USA
www.adtran.com
Asia Pacific—Beijing, China
8610 8529-8895 voice
8610 8529-8866 fax
[email protected]
Asia Pacific—Hong Kong
852 2824-8283 voice
852 2824-8928 fax
sales.asia@adtran.com
Asia Pacific—Melbourne, Australia
61 3 9225-5114 voice
61 3 9225-5050 fax
sales.asia@adtran.com
Canada--Ontario
1 416 290-0585 voice
1 416 296-1259 fax
[email protected]
Canada—Quebec
1 877 923-8726 toll free
1 514 940-2888 voice
1 514 940-2890 fax
[email protected]
Canada—Other Provinces
1 877 923-8726 toll free
sales.ca[email protected]
European Headquarters--Zürich, Switzerland
41 1 880-2777 voice
41 1 880-2778 fax
sales.europe@adtran.com
Latin America
1 954 474-4424 voice
1 954 474-1298 fax
sales.latin@adtran.com
Mexico/Caribbean
1 954 577-0357 voice
1 954 577-0358 fax
sales.m[email protected]
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 6 of 68
Northern Europe/Russia--London, United Kingdom
44 1252 626-730 voice
44 1252 617-850 fax
sales.northeurope@adtran.com
U.S. Headquarters
1 256 963-8000 voice
1 256 963-6300 fax
1 256 963-8200 fax back
[email protected]
TA 544 User Manual/61200704L1-1A
Page 7 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
Customer Service, Product Support Information, and Training
ADTRAN will replace or repair this product within 5 years from the date of
shipment if the product does not meet its published specification, or if it fails while
in service.
A return material authorization (RMA) is required prior to returning equipment to
ADTRAN. For service, RMA requests, training, or more information, see the toll-
free contact numbers given below.
Presales Inquiries and Applications Support
Please contact your local distributor, ADTRAN Applications Engineering, or
ADTRAN Sales:
Post-Sale Support
Please contact your local distributor first. If your local distributor cannot help,
please contact ADTRAN Technical Support and have the unit serial number
available.
The Custom Extended Services (ACES) program offers multiple types and levels
of service plans which allow you to choose the kind of assistance you need. For
questions, call the ACES Help Desk.
Repair and Return
If ADTRAN Technical Support determines that a repair is needed, Technical
Support will coordinate with the Custom and Product Service (CAPS) department
to issue an RMA number. For information regarding equipment currently in house
Applications Engineering (800) 615-1176
Sales (800) 827-0807
If any of the phone numbers listed on these two pages are not accessible, dial (256) 963-8000 and
ask the operator to connect you directly to the department you wish to reach.
Technical Support (888) 4ADTRAN
ACES Help Desk (888) 874-2237
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 8 of 68
or possible fees associated with repair, contact CAPS directly at the following
number:
Identify the RMA number clearly on the package (below address), and return to
the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd.
Huntsville, Alabama 35806
RMA # _____________
Training
The Enterprise Network (EN) Technical Training offers training on our most
popular products. These courses include overviews on product features and
functions while covering applications of ADTRAN's product lines. ADTRAN
provides a variety of training options, including customized training and courses
taught at our facilities or at your site. For more information about training, please
contact your Territory Manager or the Enterprise Training Coordinator by phone at
800-615-1176 ext. 7500, by fax at 256-963-7941, or by email at
[email protected].
CAPS Department (256) 963-8722
Training (800) 615-1176, ext. 7500
TA 544 User Manual/61200704L1-1A
Page 9 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
TA 544 SERIES IAD USER MANUAL
This document is designed for use by network administrators and others who will configure and provision the Total
Access®544. Itcontains overview information, informationabout navigatingthe VT 100 userinterface, configuration
information, and menu descriptions.
CONTENTS
TA544Overview................................................................13
FirmwareUpdates............................................................ 13
TerminalMenu.............................................................. 13
VoiceOverDSLOverview ........................................................13
VoiceOverATMOverview........................................................14
VoiceOverDSLApplication ......................................................14
Installation.....................................................................15
UnpackandInspecttheUnit.................................................... 15
MounttheUnit............................................................... 15
ConfiguringtheTA544 ..........................................................16
SystemInfo................................................................. 16
SystemName ............................................................16
SystemLocation ..........................................................16
SystemContact ...........................................................16
UnitName ...............................................................16
CLEICode...............................................................16
PartNumber .............................................................17
SerialNumber ............................................................17
FirmwareRevision.........................................................17
BootcodeRevision.........................................................17
SystemUptime ...........................................................17
Date/Time ...............................................................17
SystemConfig............................................................... 18
OperatingMode...........................................................18
NetworkTimingMode ......................................................18
TelnetAccess ............................................................18
TelnetUserList ...........................................................18
SNMPMenu .............................................................19
MaintPortMenu ..........................................................20
NetworkTime ............................................................21
SystemUtility ............................................................... 22
UpgradeFirmware.........................................................22
ConfigTransfer ...........................................................23
Ping ....................................................................24
ConfiguringWANSettings ..................................................... 25
DSLAMType .............................................................25
LayerOneInterface........................................................25
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 10 of 68
LayerTwoProtocol ........................................................25
ATMConfig ..............................................................25
ATMStats ...............................................................26
DSLRateConfig ..........................................................28
ConfiguringtheRouter–Configuration............................................ 29
Global ..................................................................29
Ethernet.................................................................33
WAN ...................................................................35
ConfiguringtheRouter–Status................................................. 40
Session .................................................................40
ARPcache...............................................................40
BridgeTable .............................................................40
IPRoutes................................................................40
LANStats ...............................................................41
IPStats .................................................................41
ConfiguringtheRouter–Logs.................................................. 41
SyslogHost .............................................................41
PPPLog ................................................................41
ConnectionLog ...........................................................41
NetworkLog .............................................................42
ConfiguringVoiceSupport–Config.............................................. 43
CallControl ..............................................................43
VPI.....................................................................43
VCI.....................................................................43
ConfiguringVoiceSupport–Status.............................................. 44
GatewayStats ............................................................44
PVCStats ...............................................................44
VoiceStats ..............................................................44
ClearStats...............................................................44
ManagingtheModules–Modules............................................... 45
ModulesTable............................................................45
ManagingtheModules–V.35Setup............................................. 46
ATM/FRIWF .............................................................46
AppendixA.SpecificationsandFeatures ...........................................49
AppendixB.UpdatingTA544FirmwareusingXMODEM ..............................51
Appendix C. Updating TA 544 Firmware using TFTP . . . . . . . . . .........................54
AppendixD.NavigatingtheTerminalMenus ........................................57
TerminalMenuWindow ....................................................... 57
NavigatingUsingtheKeyboardKeys............................................. 59
AppendixE.VoiceGatewayQuickStartProcedure(VoiceTurnup) .....................62
AppendixF.RFC1483QuickStart(IPRouting).......................................64
AppendixG.RFC1483QuickStart(IPRoutingwithNAT) ..............................66
Appendix H. RFC1483 Quick Start (Bridging) . . . . . . . . . . . . . . . .........................67
AppendixI.PPPoAQuickStartGuide ..............................................68
TA 544 User Manual/61200704L1-1A
Page 11 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
FIGURES
Figure1. TA544RearPanel..................................................... 13
Figure2. VoiceoverDSL....................................................... 14
Figure3. SystemInformationMenu............................................... 16
Figure4. SystemConfigurationMenu.............................................. 18
Figure5. SystemUtilityMenu.................................................... 22
Figure6. WANMenu........................................................... 25
Figure7. ATMConfigMenu..................................................... 26
Figure8. ATMStatsMenu ...................................................... 27
Figure9. Router/ConfigurationMenu.............................................. 29
Figure10. GlobalMenu.......................................................... 29
Figure11. EthernetMenu........................................................ 33
Figure12. WANMenu........................................................... 35
Figure13. Router/StatusMenu.................................................... 40
Figure14. Router/LogsMenu..................................................... 41
Figure15. Voice/ConfigMenu..................................................... 43
Figure16. Voice/StatusMenu..................................................... 44
Figure17. ModulesMenu........................................................ 45
Figure18. V.35SetupMenu...................................................... 46
Figure19. Top-levelTerminalMenuWindow......................................... 57
Figure20. ApplicationDiagram.................................................... 62
Figure21. ApplicationDiagram.................................................... 64
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 12 of 68
TA 544 User Manual/61200704L1-1A
Page 13 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
1. TA 544 OVERVIEW
The Total Access 544 is a complete solution Integrated Access Device (IAD) for Voice over ATM (VoATM) appli-
cations. The unit includes a modular network interface, Nx64 V.35 interface, 10/100BaseT interface, ISDN ports, and
an optional battery back-up (1200641L1) for added security. The TA 544 can provision, test, and provide status for
any of the voice and data interfaces. All connections are made via the rear panel (see Figure 1). In addition to a built-
in IP router, the TA 544 contains an Echo Canceller necessary for VoATM applications.
Appendix A, on page 49, contains detailed specifications for the TA 544.
Figure 1. TA 544 Rear Panel
Firmware Updates
Firmware can be updated by using XMODEM transfer protocol via the unit’s
CRAFT
port (see Figure 1) or by using
TFTP from a network server. (See Appendix B on page 51 and Appendix C on page 54.)
Terminal Menu
The terminal menu is the access point to all other operations. Each terminal menu item has several functions and sub-
menusthat identify and provideaccessto specificoperationsand parameters.Thesemenu selectionsare describedlater
in this User Manual.
2. VOICE OVER DSL OVERVIEW
Voice over DSL (VoDSL) refers to providing toll quality voice access to the Public Switched Telephone Network
(PSTN) over twisted copper pair using DSL. Data canbe combined with multiple voice lines over a single medium via
DSL, thus yielding many advantages over traditional TDM technologies.
Traditional TDM technologies are limited by statically allocating bandwidth. DSL overcomes this by providing a large
bandwidth and utilizing other technologies, such as ATM, to dynamically assign bandwidth as it is needed. Because
of this, the user is able to add voice and data connections over a DSL line with flexibility and ease.
3. VOICE OVER ATM OVERVIEW
Voice over ATM is the technology used to transmit voice conversations over a data network using Asynchronous
Transfer Mode (ATM). There are several potential benefits to moving voice over a data network using ATM. First, the
See Appendix D on page 57 for instructions about navigating the terminal menus.
ISDN
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 14 of 68
small, fixed-length cells require lower processing overhead. Second, these small, fixed-length cells allow higher trans-
mission speeds than traditional packet switching methods.
ATM allocates bandwidth on demand, making it suitable for high-speed connection of voice, data, and video services.
Conventional networks carry data in a synchronous manner. Because empty slots are circulating even when the link is
not needed, network capacity is wasted. ATM automatically adjusts the network capacity to meet the system needs.
4. VOICE OVER DSL APPLICATION
Figure 2 shows a typical VoDSL application. The TA 544 connects to the ATM network, via a DSLAM, to provide
both voice and high speed data from a single platform.
Figure 2. Voice over DSL
DS3MX
POWER
STATUS
TEST
LOCKOUT
ON LINE
APS
TEST/
ENABLE
1181020L1
DS3MX
POWER
STATUS
TEST
LOCKOUT
ON LINE
APS
TEST/
ENABLE
1181020L1
SCU
FSE
MODE
SELECT
ALM
HST
ACO
C
R
A
F
T
ACO
1181015L1
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN
=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GR
N
=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NOR
M
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN
=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GR
N
=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NOR
M
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1101L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
1181101L
1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
HTU-C
11
8
1
1
0
1L1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
QFC-C
DSX
PWR
DSX
DSX
TST
ALM
ACT
A
P
S
GRN = NORM
YEL = MAN
11
8
13
0
0
L
1
DSX
#2
#3
#4
#1
QFC-C
DSX
PWR
DSX
DSX
TST
ALM
ACT
A
P
S
GRN = NORM
YEL = MAN
1
1
8
13
00
L
1
DSX
#2
#3
#4
#1
QFC-C
DSX
PWR
DSX
DSX
TST
ALM
ACT
A
P
S
GRN = NORM
YEL = MAN
1
18
1
3
00
L
1
DSX
#2
#3
#4
#1
QFC-C
DSX
PWR
DSX
DSX
TST
ALM
ACT
A
P
S
GRN = NORM
YEL = MAN
11
8
1
30
0
L
1
DSX
#2
#3
#4
#1
HD-10 BRI Mux
POWER
DSX
LBK
1
2
3
4
5
6
7
8
9
10
DSL
1
18
1
2
0
0
L
1
HD-10 BRI Mux
POWER
DSX
LBK
1
2
3
4
5
6
7
8
9
10
DSL
1
18
1
2
00
L
1
HD-10 BRI Mux
POWER
DSX
LBK
1
2
3
4
5
6
7
8
9
10
DSL
1
1
8
1
2
00
L
1
HD-10 BRI Mux
POWER
DSX
LBK
1
2
3
4
5
6
7
8
9
10
DSL
1
18
1
2
0
0
L
1
T1-OR
PWR
DSX
LBK
LP
ALM
T
X
R
X
6V
+
–
A
P
S
TX
M
O
N
ACT
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
RX
1
1
8
1
3
1
0
L
1
T1-OR
PWR
DSX
LBK
LP
ALM
T
X
R
X
6V
+
–
A
P
S
TX
M
O
N
ACT
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
RX
1
1
8
1
3
1
0
L
1
T1-OR
PWR
DSX
LBK
LP
ALM
T
X
R
X
6V
+
–
A
P
S
TX
M
O
N
ACT
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
RX
1
1
8
1
3
1
0
L
1
T1-OR
PWR
DSX
LBK
LP
ALM
T
X
R
X
6V
+
–
A
P
S
TX
M
O
N
ACT
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
RX
1
1
8
1
3
1
0
L
1
HTU-C
11811
0
1
L
1
PWR
DSX
TX
E
Q
RX
TX
M
O
N
RX
TST
LP1
LP2
ALM
ACT
GRN=NORM
YEL=MAN
T
X
R
X
L
I
N
K
V
.3
5
R
X
V
.3
5
T
X
DATA
V
O
IC
E
B
A
T
T
P
W
R
/
N
E
T
TA 544 User Manual/61200704L1-1A
Page 15 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
5. INSTALLATION
Unpack and Inspect the Unit
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit, im-
mediately file a claim with the carrier, then contact ADTRAN Customer Service.
Shipped by ADTRAN
The following items are included in the ADTRAN shipment:
• The TA 544
•DB-9adapter
• 6 ft. RJ-45 to RJ-45 cable
• 2 wall mount hinges
• 4 each 6-32 screws
• AC power cord
• CD containing User Manual
Provided by Customer
The following items must be supplied by the customer:
• Cables and connectors used for your application
• Screws to mount the TA 544 to the wall (if applicable)
Mount the Unit
1. Use a #2 Phillips-head screwdriver to insert the 4 each 6-32 screws (all screws are provided with the unit) to
secure the bracket to the unit.
2. Use an appropriate screw (wood/metal) (provided by the user) to secure the unit to the wall.
3. Plug the unit into a grounded outlet.
Double pole/neutral fusing.
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 16 of 68
6. CONFIGURING THE TA 544
System Info
The S
YSTEM
I
NFO
menu provides basic information about the unit and contains data fields for editing information.
Figure 3 displays the submenus available when you select this menu item.
Figure 3. System Information Menu
> System Name
Provides a user-configurable text string for the name of the TA 544. This name can help you distinguish between dif-
ferent installations. You can enter up to 40 alpha-numeric characters in this field, including spaces and special charac-
ters (such as an underbar). This name will appear on the top line of all screens.
> System Location
Provides a user-configurable text string for the location of the TA 544. This field is to help you keep track of the actual
physical location of the unit. You can enter up to 40 alphanumeric characters in this field, including spaces and special
characters (such as an underbar).
> System Contact
Provides a user-configurable text string for a contact name. You can use this field to enter the name, phone number,
or email address of a person responsible for the TA 544 system. You can enter up to 40 alpha-numeric characters in
this field, including spaces and special characters (such as an underbar).
>UnitName
Product-specific name for the product assembly.
> CLEI Code
CLEI code information.
TA 544 User Manual/61200704L1-1A
Page 17 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
> Part Number
ADTRAN part number for the product assembly.
> Serial Number
Serial number of the product assembly.
> Firmware Revision
Displays the current firmware revision level of the controller.
> Bootcode Revision
Displays the bootcode revision.
> System Uptime
Displays the length of time since the TA 544 system reboot.
> Date/Time
Displays the current date and time, including seconds. This field can be edited. Enter the time in 24-hour format (such
as 23:00:00 for 11:00 pm). Enter the date in mm-dd-yyyy format (for example, 10-30-1998).
Each time you reset the system, this value resets to 0 days, 0 hours, 0 min and 0 secs.
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 18 of 68
System Config
Set up the TA 544 operational configuration from the S
YSTEM
C
ONFIG
menu. Figure 4 shows the items included in
this menu.
Figure 4. System Configuration Menu
> Operating Mode
The operating mode is set automatically.
> Network Timing Mode
Selects the timing source for the entire system. The timing options available are listed below.
Network
The clock is recovered from the network (WAN interface).
Internal
The clock is generated internally by theTA 544.
> Telnet Access
Sets Telnet access to
O
N
or
O
FF
.
> Telnet User List
Up to four users can be configured for access to the TA 544. Each user can be assigned a security level and time out.
Name
A text string of the user name for this session.
Authen Method
The user can be authenticated in two ways:
P
ASSWORD
The
P
ASSWORD
field is used to authenticate the user.
R
ADIUS
The
R
ADIUS
client is used for authenticating the user.
TA 544 User Manual/61200704L1-1A
Page 19 of 68
© 2001, ADTRAN, Inc. TA 544 User Manual
Password
When the authenticating method is password, this text string is used for the password.
Idle Time (1-255)
This sets the amount of time you can be idle before you are automatically logged off.
Level
This is the security level granted to the user.
>SNMPMenu
The TA 544 is an SNMP agent. It can respond to Gets and Sets, and can generate traps. These two lists set up the
manager, communities, and levels.
Access
When set to
O
FF
, SNMP access is denied. When set to
O
N
(def), the TA 544 will respond to SNMP manag-
ers based on the following lists.
Communities
This list is used to set up to eight SNMP communities names that the TA 544 will allow. Factory default sets
the community “public” with “Get” privileges.
Name
This is a text string for the community name.
Privilege
The access for this manager can be assigned three levels.
Manager IP
This is the IP address of SNMP manager. If set to 0.0.0.0, any SNMP manager can access the TA 544
for this community.
Traps
The TA 544 can generate SNMP traps. This list allows up to four managers to be listed to receive traps.
Manager Name
This is the text string describing the name of the entry. It is intended for easy reference and has no bear-
ing on the SNMP trap function.
Manager IP
This is the IP address of the manager that is to receive the traps.
N
ONE
No access is allowed for this community or man-
ager.
G
ET
Manager can only read items.
G
ET
/S
ET
Manager can read and set items.
TA 544 User Manual © 2001, ADTRAN, Inc.
TA 544 User Manual/61200704L1-1A
Page 20 of 68
> Maint Port Menu
The TA 544’s VT 100
CRAFT
port can be accessed via an RJ-48 located on the rear panel. The setup for these ports
is under this menu.
Password Protect
When set to
O
FF
, the maintenance port is not password protected. When
O
N
(def), the TA 544 will prompt
for a password upon startup.
Password
This is the text string that is used for comparison when password protecting the maintenance port. By
default, no password is entered.
If you forget your password, type CHALLENGE in all capital letters. Call technical support and
have the displayed CHALLENGE code ready.
The security level for the maintenance port is always set to 0. This gives full access to all menus.
Passwords are case-sensitive.
Instructions for Changing Passwords
Step Action
1
Select the
P
ASSWORD
field—a new
P
ASSWORD
field displays.
2 Type the new password in the E
NTER
field.
3 Type the new password again in the
C
ONFIRM
field.
The password can contain up to 12 alphanumeric characters.You
can also use spaces and special characters in the password.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

ADTRAN TA 544 User manual

ADTRAN
Brand
ADTRAN
Model
TA 544
Category
Networking
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents