Compaq Deskpro AP550 Reference guide

Compaq Professional Workstation AP550

Hardware Reference Guide

191010-001

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: a-title.doc

Last Saved On: 04/12/00 2:19 PM Last Saved By: Lydia Sanchez

Professional Workstation AP550

Hardware Reference Guide

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: b-notice.doc

Last Saved On: 04/12/00 2:20 PM Last Saved By: Lydia Sanchez

Notice

Compaq Computer Corporation shall not be liable for technical or editorial errors or

omissions contained herein. The information in this guide is subject to change without notice.

Compaq product, no part of this guide may be photocopied or reproduced in any form without

prior written consent from Compaq Computer Corporation.

COMPAQ and the Compaq logo Registered in U.S. Patent and Trademark Office.

Microsoft, Windows, Windows NT, Windows 2000 Professional, and other names of

Microsoft products referenced herein are trademarks or registered trademarks of Microsoft

Corporation.

Intel and Pentium are registered trademarks of Intel Corporation.

All other product names mentioned herein may be trademarks or registered trademarks of

their respective companies. Printed in U.S.A.

The following words and symbols mark special messages throughout this guide:

WARNING:

Text set off in this manner indicates that failure

to follow directions could result in bodily harm or loss of life.

CAUTION:

Text set off in this manner indicates that failure

to follow directions could result in damage to equipment or

loss of information.

Compaq Professional Workstation AP550

Hardware Reference Guide

First Edition (June 2000)

Part Number 191010-001

Compaq Computer Corporation

Compaq Professional Workstation AP550 Hardware Reference Guide iii

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: c-toc.doc

Last Saved On: 04/18/00 2:30 PM Last Saved By: Lydia Sanchez

C

ONTENTS

chapter 1

Product Features

Standard Configuration Features............................................................................................. 1-1

Front Panel Components ......................................................................................................... 1-2

Rear Panel Components .......................................................................................................... 1-3

System Board Components ..................................................................................................... 1-4

Changing from a Minitower to a Desktop Configuration ....................................................... 1-5

Changing from a Desktop to a Minitower Configuration ....................................................... 1-8

Windows Logo Key .............................................................................................................. 1-11

Special Mouse Functions....................................................................................................... 1-11

Serial Number Location ........................................................................................................ 1-11

chapter 2

Hardware Upgrades

Installation Sequence............................................................................................................... 2-2

Removing the Workstation Access Panel................................................................................ 2-3

Removing the Front Bezel....................................................................................................... 2-4

Installing Additional Memory................................................................................................. 2-5

Installing and Removing RIMMs ...................................................................................... 2-6

RIMM Slot Locations .................................................................................................. 2-6

Guidelines for RIMM Installation................................................................................ 2-7

Installing RIMMs......................................................................................................... 2-8

Removing RIMMs ....................................................................................................... 2-9

Installing Additional Drives .................................................................................................. 2-10

Drive Bay Components ................................................................................................... 2-10

Preparing for Drive Installation............................................................................................. 2-11

Removing the Bezel Blank ........................................................................................ 2-11

Locating the Hardware Screws .................................................................................. 2-13

Installing a Drive ............................................................................................................. 2-14

Installing a Hard Drive in a 3.5-inch Drive Bay........................................................ 2-14

Installing a Hard Drive in a 5.25-inch Drive Bay...................................................... 2-16

Removing a Drive............................................................................................................ 2-18

Installing and Removing an Expansion Board ...................................................................... 2-21

Identifying the PCI Expansion Slots................................................................................ 2-21

Installing an Expansion Board......................................................................................... 2-22

Removing an Expansion Board ....................................................................................... 2-24

Identifying the AGP Graphics Controller Expansion Slot............................................... 2-24

Installing and Removing an AGP Graphics Controller ................................................... 2-25

Installing a Processor ............................................................................................................ 2-26

Index

..................................................................................................................................................... I-1

Compaq Professional Workstation AP550 Hardware Reference Guide 1-1

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

?D=FJAH



P

RODUCT

F

EATURES

Standard Configuration Features

The Compaq Professional Workstation AP550 is a minitower system

that can be easily converted to a desktop. Features may vary depending

on your model. For a complete listing of the hardware and software

installed in your workstation, run the INSPECT utility described in the

Troubleshooting Guide.

1-2 Product Features

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

Front Panel Components

1 CD-ROM eject button

2 CD-ROM drive activity light

3 CD-ROM headphone jack

4 CD-ROM volume

5 Diskette drive activity light

6 Diskette eject button

7 Power button

8 Power-on light

9 Hard drive activity light

Compaq Professional Workstation AP550 Hardware Reference Guide 1-3

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

Rear Panel Components

Rear panel components

1 Power cord connector

2 Line-out audio connector

3 Headphone connector

4 Keyboard connector

5 Two universal serial bus (USB) connectors

6 RJ-45 connector

7 Ultra3 SCSI connector

8 Line-in audio connector

9 Microphone connector

: Mouse connector

; Parallel connector

< Serial connector (COMM1)

= Serial connector (COMM2)

> VGA (AGP) Video connector

1-4 Product Features

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

System Board Components

System board components

1 Four PCI expansion slots

2 AGP expansion slot

3 Serial port cable connector

4 Direct Rambus RIMM sockets 1-4

5 Ultra3 SCSI connector

6 Primary processor

7 Embedded Processor Power Module for primary processor

8 Secondary processor slot

9 Processor Power Module connector for secondary processor

: Power connectors

; Power switch and power LED connector

< Secondary Ultra ATA (IDE) connector

= Primary Ultra ATA (IDE) connector

> Diskette drive connector

τ Battery

ψ Power-on password (P49) enabled jumper

υ CMOS Pushbutton Switch

Compaq Professional Workstation AP550 Hardware Reference Guide 1-5

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

Changing from a Minitower to a Desktop Configuration

To change from a minitower to a desktop configuration:

1. Turn off the workstation and any external devices.

2. Disconnect the power cord from the grounded AC outlet and the

back of the workstation, and then disconnect the network cable

from the system.

3. Remove the workstation access panel. Refer to the instructions

 Removing the Workstation Access Panel in Chapter 2.

4. Remove the front bezel. Refer to  Removing the Front Bezel in

Chapter 2.

5. Disconnect all power and data cables from the drives in the

5.25-inch drive bay.

6. To release a drive from the 5.25-inch drive bay, slide the drivelock

as shown. Carefully push the drive from the back of the unit until

the drive casing can be grasped.

Releasing the drives with the drivelock

CAUTION: Do not hold the faceplate while removing a drive. Only

hold a drive by its casing.

1-6 Product Features

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

7. While holding the drive casing, gently pull the drives out of the

drive bay.

CAUTION: When removing the drives, do not pull the drives from the

front of the drive bay. To prevent damage to the drive bezel, push the

drives from the rear to remove them from the front of the drive bay.

8. After placing the workstation in the desktop position, gently slide

the drives back into the bay.

Installing the drives

CAUTION: The use of unnecessary force when installing the drive

may result in damage to the drive.

✎

Always place the diskette drive in the bay nearest the top

(bay 3) of the chassis in the desktop configuration to ensure

proper drive clearance and access. When all of the drives are

properly inserted, the drivelock will secure the drives in place.

9. Reconnect the power and data cables to the drives as labeled.

Compaq Professional Workstation AP550 Hardware Reference Guide 1-7

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

10. Remove the bezel blank as described in the Removing the Bezel

Blank section in Chapter 2 and reposition the subpanel with the

bezel blank in the proper orientation for the desktop configuration.

CAUTION: Hold the subpanel straight when you pull it away from the

front bezel. Pulling the subpanel away at an angle could damage the

pins that align it within the front bezel.

Changing from a minitower to a desktop configuration

11. Replace the subpanel, front bezel, and the workstation access

panel. Be sure the subpanel and front bezel align properly with the

alignment tabs.

✎

When converting from a minitower to a desktop orientation,

use the replacement bezel blank that was shipped with your

workstation to ensure the Compaq logo is properly oriented.

12. Reconnect the power cord to the grounded AC outlet, then

reconnect the network cable and any external devices to the

system.

1-8 Product Features

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

Changing from a Desktop to a Minitower Configuration

To change from a desktop to a minitower configuration:

1. Turn off the workstation and any external devices.

2. Disconnect the power cord from the grounded AC outlet and the

back of the workstation, and then disconnect the network cable

from the system.

3. Remove the workstation access panel. Refer to  Removing the

Workstation Access Panel in Chapter 2.

4. Remove the front bezel. Refer to  Removing the Front Bezel in

Chapter 2.

5. Disconnect all power and data cables from the drives in the

5.25-inch drive bay.

6. While pressing the drivelock button, push from the back of the

drives until the drive casing can be grasped.

Releasing the drives with the drivelock

1. While holding the drive casing, pull the drives out of the drive bay.

Compaq Professional Workstation AP550 Hardware Reference Guide 1-9

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

2. After placing the workstation in the desktop position, gently slide

the drives back into the bay.

Installing the drives

CAUTION: The use of unnecessary force when installing the drives

may damage the drives.

✎

Always place the diskette drive in the bay nearest the internal

3.5-inch drives in the minitower configuration for proper

clearance within the chassis. When the drives are properly

inserted, the drivelock will secure them.

9. Reconnect the power

and data cables to the drives as labeled.

1-10 Product Features

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

10. Remove the bezel blank as described in the Removing the Bezel

Blank section in Chapter 2 and reposition the subpanel with the

bezel blank in the proper orientation for the desktop configuration.

CAUTION: Hold the subpanel straight when you pull it away from the

front bezel. Pulling the subpanel away at an angle could damage the

pins that align it within the front bezel.

Changing from a desktop to a minitower configuration

11. Replace the subpanel,

front bezel, and workstation access panel. Be sure the subpanel and

front bezel align properly with the alignment tabs.

✎

When converting from a desktop to a minitower orientation,

use the replacement bezel blank that is shipped with your

workstation to ensure the Compaq logo is properly oriented.

12. Reconnect the power

cord to the grounded AC outlet, then reconnect the network cable

and any external devices to the system.

Compaq Professional Workstation AP550 Hardware Reference Guide 1-11

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: d-ch01.doc

Last Saved On: 05/08/00 10:38 AM Last Saved By: Jean Schuck

Windows Logo Key

Use the Windows Logo key in combination with other keys to perform

certain functions in Windows 2000 Professional and Windows NT

Workstation 4.0.

Windows logo key + F1 Displays a pop-up menu for the

selected object.

Windows logo key + Tab Activates the next Taskbar button.

Windows logo key + E Launches Explore My Computer.

Windows logo key + F Launches Find Document.

Windows logo key + Ctrl + F Launches Find Computer.

Windows logo key + M Minimizes all open applications.

Shift+Windows logo key + M Undoes Minimize All.

Windows logo key + R Displays Run dialog box.

Special Mouse Functions

Most software applications support the use of a mouse. The functions

assigned to each mouse button depend on the software application you

are using.

Serial Number Location

Each computer has a unique serial number located on the corner of the

computer access panel and on the rear panel of the computer. Keep this

number available when contacting Compaq customer service.

Compaq Professional Workstation AP550 Hardware Reference Guide 2-1

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: e-ch02.doc

Last Saved On: 04/18/00 2:28 PM Last Saved By: Lydia Sanchez

chapter

2

H

ARDWARE

U

PGRADES

This chapter explains how to remove the workstation access panel and

convert the minitower workstation to a desktop unit or the desktop

workstation to a minitower unit. It also explains how to install the

following hardware:

■ Memory

■ Drives

■ Expansion boards

■ Processors

✎

Compaq recommends that you finish the setup procedures for

the preinstalled software before you install any optional

hardware or third-party devices that were not included with

your workstation.

2-2 Hardware Upgrades

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: e-ch02.doc

Last Saved On: 04/18/00 2:28 PM Last Saved By: Lydia Sanchez

Installation Sequence

Follow this sequence of steps to ensure the proper installation of any

optional equipment. Before you begin, observe the following

precautions:

!

WARNING: To reduce the risk of personal injury from hot surfaces,

allow the internal system components to cool before touching them.

!

WARNING: To reduce the risk of electrical shock, fire, or damage to

the equipment, do not plug telecommunications/telephone

connectors into the network interface controller (NIC) receptacles.

CAUTION: Static electricity can damage the electronic components

of the workstation or optional equipment. Before beginning these

procedures, ensure that you are discharged of static electricity by

briefly touching a grounded metal object.

1. Turn off the workstation and disconnect the power cord from the

grounded AC outlet and the back of the workstation.

2. Open the workstation by removing its workstation access panel.

See the section  Removing the Workstation Access Panel in this

chapter for instructions.

3. If you are installing or removing drives in the front bays, see the

section  Removing the Front Bezel in this chapter for

instructions.

4. Install any optional equipment, such as memory, drives, expansion

boards, processors, or batteries. See the appropriate sections in this

chapter or the appendices for installation instructions.

5. Replace the front bezel and the workstation access panel, if

necessary.

6. Reconnect the power cord to the back of the workstation and plug

the power cord into a grounded AC outlet.

7. Turn on the monitor, workstation, and any devices you installed.

8. Reconfigure the workstation, if necessary.

9. Test the workstation (optional) using the TEST utility.

Compaq Professional Workstation AP550 Hardware Reference Guide 2-3

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: e-ch02.doc

Last Saved On: 04/18/00 2:28 PM Last Saved By: Lydia Sanchez

Removing the Workstation Access Panel

To remove the workstation access panel:

1. Turn off the workstation and any external devices.

2. Disconnect the power cord from the grounded AC outlet and the

back of the workstation.

3. Refer to the following illustration to remove the workstation

access panel.

Loosening the two thumbscrews and removing the workstation access panel

✎

When replacing the workstation access panel, be sure to

tighten both thumbscrews.

2-4 Hardware Upgrades

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: e-ch02.doc

Last Saved On: 04/18/00 2:28 PM Last Saved By: Lydia Sanchez

Removing the Front Bezel

To remove the front bezel:

1. Turn off the workstation and any external devices.

2. Disconnect the power cord from the grounded AC outlet and the

back of the workstation

3. Remove the workstation access panel. Refer to  Removing the

Workstation Access Panel in this chapter.

4. Push in on the two front bezel release tabs, then rotate the front

bezel away from the chassis to release it.

Pressing the front bezel release tabs to remove the front bezel

✎

When replacing the front bezel, ensure that the bottom hinge

points are properly placed in the chassis before rotating the

front bezel back into its original position.

Compaq Professional Workstation AP550 Hardware Reference Guide 2-5

Compaq Confidential - Need to Know Required

Writer: Beth Zanca Part Number: 191010-001 File Name: e-ch02.doc

Last Saved On: 04/18/00 2:28 PM Last Saved By: Lydia Sanchez

Installing Additional Memory

The Compaq Professional Workstation AP550 supports Direct Rambus

inline memory modules (RIMMs). Additional RIMMs are available to

upgrade the memory. A maximum of 32 count Direct RDRAM devices

is supported on each Direct Rambus memory channel. Continuity

RIMMs (CRIMMs) must populate any empty slots.

Page is loading ...

Compaq Deskpro AP550 Reference guide

This manual is also suitable for

Compaq Deskpro AP550 Reference guide

Related papers

Other documents