Addonics Secure NAS R5 User guide

Brand: Addonics

Model: Secure NAS R5

Category: NAS & storage servers

Type: User guide

Addonics Secure NAS R5 is a high-performance network attached storage device that provides secure and reliable data storage and sharing. It features RAID 0, 1, 3, 5, and 10 support for data protection, and JBOD mode for individual drive access. With its hot-swappable drive bays, you can easily add or replace drives without powering down the system. The Secure NAS R5 also includes a CipherChain module for hardware encryption, ensuring the security of your data. It is suitable for small businesses, workgroups, and home users who need secure and scalable storage.

Technical Support

If you need any assistance to get your unit functioning properly, please have

your product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

T E C H N O L O G I E S

www.addonics.com

Secure NAS R5

(SN535E1G)

User Guide

Firmware v87a

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Overview

1 42 3

8 9 10

2 3 4

Front View

SN535E1G

Back View

6 7

1.Reset Button

2. HDD

3. Cipher Key Socket

4. Power

5. Drive Activity LED

6. Power

7. NAS Status

8. RAID Error

9. Drive Error

10. Power

1. Extra Connector for Direct Attach Storage

2. Power LED

3. Status LED

4. DIP Switches for RAID Setting

5. Reset

6. RJ45 Connector for LAN Connecting

7. USB Connector for Additional USB Storage

8. 40x40mm Cooling Fan

9. Power Cord Socket

10. 110 / 240 V Switch

11. 320w ATX Power Supply

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Power Cord (U.S. Version Shown) eSATA Cable

Network CableCipher Keys

WARNING: Please remember to

set the power supply to your local

outlet voltage prior to plugging in

the power cord. Failure to do so

may damage the power supply.

Power LED (next to Power Switch): glows green while unit is turned on.

Power LED (on Cipher Chain Module): glows green when Cipher is unlocked.

Drive Activity LED: Glows blue to indicate power, flashes magenta (blue

and red) to indicate activity.

HDD LED (on Cipher Chain Module): blinks to indicate RAID activity.

NAS Status LED (front and rear): glows when idle, blinks to indicate the unit

is booting or busy.

RAID Error: glows to indicate the RAID is either degraded or offline, blinks to

indicate rebuilding is in progress.

Drive Error: blinks to indicate a spare drive that is rebuilding.

RESET button (on Cipher Chain Module): press to activate with inserted key

(or deactivate if no key is inserted).

RESET button (rear, on NAS module): press and hold as described in

Resetting the NAS Unit.

SET button (rear, next to dipswitch): press and hold during power-up to set

or reset the RAID setting.

POWER LED (rear, on NAS module): indicates the NAS module is powered up.

RAID Setting Dipswitch: used with SET button to define or delete a RAID array.

DAS Connector: used for connecting the RAID array to an external computer.

RJ45 Connector: used for connecting to 10/100/1000 Mbit network.

USB Connector: used for attaching additional USB 2.0 storage to the NAS unit.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Installation

Network Connection

The Secure NAS unit is factory configured for dynamic IP addressing (DHCP

client). Connect the unit to a network (router or switch) where DHCP is

supported. Static IP may be assigned later after initial setup.

Storage

The Secure NAS unit does not support FIS switching for port multipliers,

otherefore the installed drives must be configured as a RAID array. Externally,

through the use of USB hubs, up to a total of 16 physical storage devices may

be connected, counting the Secure NAS unit's RAID array. One SATA port

multiplier in JBOD mode may be connected using USB; however, with more

than one such port multiplier connected only one will function – others will not

be recognized at all.

Each physical unit may be formatted with up to 4 individual partitions using a

Master Boot Record (MBR), or up to 15 individual partitions using a GUID

Partition Table (GPT). Supported file systems are: FAT32, ext2, ext3, ext4, XFS,

and NTFS. The NAS 4.0 unit will by far provide the best performance when

using the XFS file system on the Secure NAS unit's RAID array.

NOTE: Initializing a drive with MBR is limited to drives less than 2TB in capacity with up to 4

partitions total. For drives greater than 2TB in capacity or if more than 4 partitions are desired, the

drive must be initialized using a GPT boot record.

Cipher key

The two cipher keys have an identical, unique encryption code. One of these

keys should be kept in a safe and secure location and can be sent back to

Addonics for duplicating additional keys. If you are down to the last key, be sure

to make a back up of all the data stored inside your NAS unit prior to sending

the last key to Addonics. Addonics is not responsible for keys lost in the mail or

for retrieval of the data inside the encrypted hard drive.

IMPORTANT: There is no back door for the Cipher tower encrypted hard

drives if the Cipher keys are lost or stolen.

The Secure NAS unit's RAID Array is directly connected to the CipherChain

module internally. The Cipher Key must be inserted before powering up the unit

in order to configure the RAID array. During normal operation, the RAID array

may only be accessed while the CipherChain module is unlocked by either

powering up the unit or pressing the CipherChain RESET button while the

Cipher Key is inserted. The POWER LED on the CipherChain module indicates

the CipherChain is unlocked. If the CipherChain POWER LED is not glowing,

the RAID array cannot be configured or accessed.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Drive Installation

1. Be sure all doors are unlocked, use the provided keys to unlock if needed.

2. Gently pull the lever on the door to release it.

3. Insert the drive as shown on the label inside the door: The SATA connector

toward the rear, with label side to the right. The drive should slide in easily,

don't force it.

4. Close the door on the drive bay. It should also give little resistance, don't force

it. It can help to slightly tug the lever while snapping the door shut to make it

easier. As soon as the drive is in position it will power up.

5. The drives may be locked in place if desired.

Direct Attached Storage (“DAS”) Connector

The Secure NAS unit's RAID array may be connected from the DAS connector

directly to a computer using the eSATA cable provided. This connection can be

useful for adding content directly to the RAID array.

NOTE: The DAS Connector is a hardware controlled switch, activated by inserting an eSATA cable

into the eSATA port on the back of the Secure NAS unit. The Secure NAS unit's RAID array will

instantly disconnect from the NAS controller inside the unit, even if there is nothing connected to the

other end of the eSATA cable. DO NOT connect an eSATA cable to the DAS Connector except

when using the RAID array with an external computer.

RAID Configuration

The Secure NAS unit does not support SATA Port Multipliers. Using the unit with

more than one drive requires a RAID configuration.

Using identical drives for all settings other than LARGE is strongly

recommended. Creating a LARGE array using drives that have different

properties will use all space on all members, and performance will match that of

the member in use during any particular I/O operation. Creating a RAID using

drives that are not all the same size will result in all members using only as

much space as the smallest member. Creating a RAID using drives that have

different performance will degrade the overall performance of the array.

Any number of drives may be installed in the unit, the RAID Modes available are

as follows:

NOTE: RAID 0 and LARGE modes are NOT recommended for use on the Secure NAS unit.

Number of drives

RAID Mode

JBOD Mode only

RAID 0, 1, CLONE, LARGE

RAID 0, 3, 5, CLONE, LARGE

RAID 0, 10, 3, 5, CLONE, LARGE

RAID 0, 3, 5, CLONE, LARGE

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

RAID Modes

The Secure NAS unit supports one drive in JBOD Mode, several types of RAID

and some non-RAID drive sets. Each configuration has different properties and

requirements, as follows:

JBOD Mode (Individual Drives)

Number of drives: 1

Unit capacity: N/A

Spares: no

Fault tolerance: none

JBOD mode may only be used with one drive installed in the Secure NAS unit.

RAID 0 (Stripe set)

Number of drives: at least 2

Unit capacity: size of each member times number of members.

Spares: no

Fault tolerance: none - if any member is lost all data is lost (see note).

RAID 0 “stripes” the file system across the array by placing “chunks” of data

sequentially between drives in a specific order.

NOTE: Risk of data loss compared to a single drive multiplies by the number of

members in a RAID 0.

RAID 1 or 10 (Mirror set, Stripe of mirror sets)

Number of drives: 2 (RAID 1) or 4 (RAID 10).

Unit capacity: size of one member (RAID 1) or size of two members (RAID 10).

Spares: yes – if EZ mode is not disabled and 3 (RAID 1) or 5 (RAID 10) drives

are present, the array will be initialized with a spare.

Fault tolerance: RAID 1 can withstand the loss of one drive without losing data.

RAID 10 can withstand the loss of one drive from each mirror set without losing

data.

RAID 1 works by duplicating the exact same data on two drives.

RAID 10 works by using two RAID 1 sets configured as members of a RAID 0.

Disks 1 and 2 are mirrored, disks 3 and 4 are mirrored, and the two mirror sets

are striped together.

RAID 3 (Stripe set with dedicated parity)

Number of drives: at least 3

Unit capacity: size of one member times number of members minus one.

Spares: yes

Fault tolerance: can withstand the loss of one drive without losing data.

RAID 3 works by striping data for individual I/O blocks across all members

except one, which contains parity data for the stripe set computed internally by

the Port Multiplier. In the event of failure, the missing information can be

calculated using the parity information.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

RAID 5 (Stripe set with striped parity)

Number of drives: at least 3

Unit capacity: size of one member times number of members minus one.

Spares: yes

Fault tolerance: can withstand the loss of one drive without losing data.

RAID 5 works by striping entire I/O blocks across all members of the set, with

each member taking turns carrying parity data computed by the Port Multiplier.

In the event of failure, the missing information can be calculated using the parity

information.

CLONE (Mirror set)

Number of drives: at least 2

Unit capacity: size of one member.

Spares: yes

Fault tolerance: can withstand the loss of any number of drives without losing

data as long as at least one complete member remains online. CLONE mode

works the same way as RAID 1, by maintaining a complete copy of the entire

set of data on each drive.

LARGE (Spanned set)

Number of drives: at least 2

Unit capacity: 100% of all drives together regardless of differences in size

Spares: no

Fault tolerance: cannot withstand the loss of any drives without losing data.

However, some data may be recovered as long as the drive(s) carrying the file

system data (boot record, directory, etc.) remain online. LARGE mode is neither

a RAID nor is it a JBOD. It works by declaring the sum of all available space of

the member drives as a single unit, without striping the data. As each member is

filled, new data is stored on the next.

Notes about Spare Drives

To create an array with one or more spares, set or modify the RAID mode while

the spares are not inserted in the RAID array. When EZ mode is enabled

(SW1:2 OFF), individual drives connected when an array is present are

considered spare. Spare drives must be equal to or larger in size than the

smallest member. When any type of array is defined, individual units will be

considered spare.

If EZ mode is disabled (SW1:2 ON), all individual drives not configured as array

members will be offered to the host adapter as separate units. The Secure NAS

unit does not the Port Multiplier's switching protocol, so this feature is not

supported.

RAID 0 and LARGE arrays are not fault-tolerant and spare drives will not be

useful. When a spare drive is present and a fault-tolerant RAID (1, 10, 3, 5, or

CLONE) is defined, EZ mode will automatically rebuild any available spares into

the array to replace a failed member. During this process, the spare drive's Error

LED will flicker along with the RAID Error LED until rebuilding is complete.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Configuring the RAID Using Dipswitches

Resetting the RAID

NOTE: This procedure destroys all RAID data. It should not harm individual

drives or their contents; however, creating backups of all data is strongly

recommended before proceeding.

Be sure the port multiplier is connected to an active host before proceeding. The

port multiplier will not complete the process if it has no host connection.

1. Power down the unit and set the dip switch to the desired RAID Mode.

2. While holding the SET button, turn the unit on. A long beep will sound from

the Port Multiplier. The SET button may be released once the long beep starts.

Shortly after releasing the SET button, the port multiplier should “chirp” to

indicate the process is complete. If instead of a chirp the Port Multiplier sounds

a series of short beeps, an error has occurred during the process.

Setting or Modifying the RAID Mode

NOTE: Setting or modifying the RAID mode destroys all data.

Be sure the port multiplier is connected to an active host before proceeding. The

port multiplier will not complete the process if it has no host connection.

1. Follow the procedure for resetting the RAID Mode.

2. Power down the unit and set the dip switch to the desired RAID Mode.

3. While holding the SET button with a ballpoint pen, turn the unit on. A long

beep will sound from the Port Multiplier. The SET button may be released once

the long beep starts.

Shortly afterward, the port multiplier should “chirp” to indicate the process is

complete. If instead of a chirp the Port Multiplier sounds a series of short beeps,

an error has occurred during configuration of the array.

BZS Switch (SW1:1):

The BZS switch is used to silence the audible alarm buzzer. The OFF position

permits the audible alarm, and the ON position silences the audible alarm. The

BZS switch has immediate effect.

EZ Switch (SW1:2):

The EZ (spare) switch inhibits spares when ON. When in the OFF position, all

individual drives (not defined as members of an array) are considered spare and

are not offered to the operating system. Should a RAID become degraded,

when the EZ switch is in the OFF position a spare drive will be used

automatically to rebuild the RAID, if present. EZ mode is determined when the

unit is powered up. Changing the switch will have no effect until the unit has

been re-powered.

Warning: turning off the EZ switch to rebuild an array will consider any

drives not declared array members to be eligible for rebuild as a spare.

Rebuilding will destroy all existing data on that drive and the drive chosen

is not predictable. Disconnect any individual drives with valuable data on

them before enabling EZ Mode.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

The NAS Controller Unit Boot Process

Upon powering up the unit, the status LED will blink at first between bright and

dim, then remain dark for a few moments, then begin to blink between bright

and dark for a while and finally settle down to glowing steadily. Once this

pattern is complete the unit is ready to communicate.

This process normally takes about a minute or less, but may take longer

depending on the complexity of the configuration, storage and LAN

connections. With the 240 possible file systems, booting may take several

minutes or longer.

Resetting the NAS Controller

Should a problem arise with the NAS Controller or its configuration, the unit

may be reset simply by turning the unit off, then back on after a few moments. If

this doesn't clear the problem, the unit may be returned to its factory

configuration by gently pressing and holding the reset button between the

power and LAN connectors until the Status LED blinks slowly, then rapidly. After

releasing the Reset button while blinking slowly there will be no changes. After

releasing the button once the Status LED blinks rapidly, the Status LED will

continue to blink for a while, and may possibly glow steadily for a while as well.

Eventually it will begin the boot process, beginning with blinking between bright

and dim. Once the boot process is complete and the LED is glowing steadily

again, all settings will have been cleared and the unit is ready to communicate

with all settings reset to the factory default – including the network and device

name settings.

If the process appears to become stuck or takes too long to complete, you can

try disconnecting power, then reconnect and after the Status LED blinks bright

and dark a few times, try the Reset button again.

RAID Mode Switches M2, M1, M0 (SW1:3 – SW1-5)

The RAID Mode switches define what type of RAID will be initialized when the

unit is powered up while the RAID Mode button is held down, as follows:

NOTES:

1. Audible Alarm is recommended at all times.

2. EZ mode has no effect when no array is defined.

3. Disabling EZ for RAID 0 and LARGE is strongly recommended.

Dipswitch Position

1 (BZS)

2 (EZ) 3 (M2) 4 (M1) 5 (M0)

JBOD (Individual

Drives)

* FACTORY

DEFAULT SETTING

OFF

OFF OFF OFF

RAID 0 OFF

ON ON ON

RAID 1 OR 10 OFF OFF ON ON OFF

RAID 3 OFF OFF ON OFF OFF

RAID 5 OFF OFF OFF ON OFF

CLONE OFF OFF OFF ON ON

LARGE OFF ON ON OFF ON

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Once you have connected to the Web Interface, the Initial Setup page will appear:

Click Next, then a dialog will appear requesting the Administrator login. The

default username is "admin" and the password is "123456" (without the

double-quote marks). Next, set a custom password for the admin account. The

admin account name may also be changed.

Initial Setup

Windows: All of the Secure NAS unit's functions and features are configured

using a Web Interface. Once the hardware is installed, access the Web

Interface with a web browser on a computer attached to the same network by

typing in “http://addnas” - this will work on most Windows systems. Be sure the

computer accessing the NAS has the Workgroup name set to WORKGROUP.

MAC: Mac users may need to determine the Secure NAS unit's IP address by

opening a Terminal window and typing the following command:

smbutil lookup addnas

This utility should return the Secure NAS unit's IP address. Typing this address

into the web browser should open the Secure NAS unit's Web Interface.

Linux: Linux users may need to determine the Secure NAS unit's IP address if

Windows name resolution support is not fully installed and configured, by

examining the DHCP server's clients table and attempting to connect to each

unidentified IP address using a browser until the Secure NAS unit's Web

Interface appears.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Finally, review and confirm the settings:

After clicking on the Update settings button, Initial Setup is complete.

Sharing Files Using the Secure NAS

SMB (Windows Sharing)

Connecting to the NAS for direct file access through Windows Explorer is very similar

to sharing files between Windows systems. Typing “\\ADDNAS” (or the Secure NAS

unit's hostname if changed from the default) or the double-backslash followed by the

Secure NAS unit's IP address is the easiest way to gain direct access quickly. After

pressing Enter, the Explorer Window should show a list of the shares available.

Opening any of the shares is like opening any other folder, except when accessing a

share for the first time, Windows may request a username and password for access

to the share (unless “Everyone” permissions have been changed from the default

setting of NONE). Entering a valid username and password will open the folder with

appropriate access rights to that user. If “NONE” permissions are set for that user on

that share, Another username and password prompt will appear. After connecting to

a share, Windows will use the same username and password for all connections until

the Windows user logs off of Windows.

Next, set up the Date and Time. Choose a city nearest you in the same Time

Zone and be sure the Date and Time are correct.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

On Mac systems, on the Finder's Go menu choose “Connect to Server...” then in

the server address box type “smb://” followed by the Secure NAS unit's IP

address. On Linux systems, use the “Connect to share...” dialog found on the

Nautilus or “File Manager” menu bar, then select Windows Share for the type and

complete the remaining fields for share name, username and password.

Information required to complete the connection and the system's response vary

from one version of Linux to another, and should be expected to work about the

same way as connecting to a share on an actual Windows PC.

FTP Server

The Secure NAS FTP Server requires the "User Home Directory Drive" is defined

under the Sharing Tab to function. Anonymous login is supported with no user

home directory and access to any shares with read-only or read and write access

to "Everyone" for FTP. Authenticated users will have read and write access to their

home folder and any other shares defined under the Sharing tab with read-only or

read and write access for the user for FTP, as well as "Everyone."

Getting Started with MLDonkey

MLDonkey is a powerful, multi-protocol Peer-to-Peer (P2P) client included with the

Secure NAS unit. The features and capabilities of this tool are beyond the scope of

this user guide, the steps below will show how to get MLDonkey up and running.

For more information on how to use MLDonkey, visit

http://mldonkey.sourceforge.net.

MLDonkey Basic Setup

The MLDonkey client requires one partition formatted with either ext3 or XFS. The

Secure NAS unit's format utility can format one physical unit with a single partition

using all space if needed.

Under the P2P/MLDonkey tab, choose the drive you wish to create the file

structure on and click Save. Please note: this menu will permit setting up folders

on incompatible file systems. If this is done, MLDonkey will not start or may not be

able to download files.

When the folder structure is set up, a page will appear stating this is done. Click

the START button. NOTE: The MLDonkey setup page will create a share on the

selected drive called MLDonkey. This share will be configured with “None”

permissions to “Everyone” as well as all existing users.

Next, a new page will appear stating MLDonkey is running. Click the link at the

bottom of the page that reads “Launch MLDonkey Control Panel.”

A new tab will appear in the browser with the MLDonkey web interface. If

MLDonkey is not fully initialized yet, the browser may report a failure to connect. If

this happens, wait about one minute and try again, either by refreshing the page or

clicking a “try again” button – this step varies depending on the browser used.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

When first setting up, a prompt appears warning there is no password for the

admin account. Click the space between the “DL” and “Input” buttons, then type

the command “useradd admin” as shown, then add a password after a space.

NOTE: The MLDonkey admin account is not the same account as the Secure NAS unit's web interface

admin account. It is recommended that the password matches for simplicity, but not necessary.

MLDonkey will perform most of the remaining steps automatically and connect to

some servers on the Donkey network.

To download a file using the Donkey network, begin by clicking search, then enter

some criteria and click the Search button. After a query message appears, click

the "Search Results" button.

To download a Torrent, on the command bar type dllink followed by a space and

the full URL path to the .Torrent file and press Enter or click Input. (example: "dllink

http://sampletorrent.com/path/dot-torrentfile.torrent"). MLDonkey will parse the

download and add it to the download queue automatically.

Files queued for download will appear in the MLDonkey share in the incoming/files

folder when when complete.

NOTE: this folder has read-only permissions and cannot be changed.

The Configuration Tab

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Change Current Date and Time

Settings for time zone, date and time. Set time zone to a listed city nearby in the

same time zone.

Update Device/Workgroup Names

Settings for the Secure NAS unit's network name and Windows workgroup.

Default setting is ADDNAS joined to WORKGROUP. Setting the workgroup name

on all devices on the same network to match is strongly recommended. The

Device name is used for accessing the Web Interface as well as browsing for the

shared folders on the network.

Update FTP Port Number

Changes the TCP Port used by the FTP server. Default is port 21. Note that some

FTP clients will not be able to connect on alternate ports.

View Current Network Configuration

Displays details about the Secure NAS unit's current network settings. Includes

device and network names as well as TCP/IP settings.

Configure the Network Settings

Starts the network configuration wizard.

Update Admin Username and Password

Changes the web interface management login.

Configure User Home Directory Drive

Determines which drive on the system carries the HOME directory for users. The

user's home folder is required for FTP transfers and as a network share for private

files. If a home directory is already defined it will be shown. Choose a volume and

click Save. If any files exist in a previous Home directory they will be moved to the

new location.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Choosing Automatic will configure the Secure NAS unit as a DHCP client and the

configuration wizard will skip to the end. Choosing Manual configuration will

proceed to Step 2.

Step 2 configures the Secure NAS unit's static IP address and subnet mask. To

choose a working static IP address, make sure you meet these criteria:

1. The subnet mask must match the rest of the network exactly.

2. The IP address must match the router's IP address exactly where the subnet

mask is "255."

3. The IP address cannot end in 0 or 255.

4. The IP address must not match any other system on the network.

5. The IP address should not be within the DHCP server's client pool.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

The next step is to configure network connections. The gateway is usually the

internal IP address for the router the Secure NAS unit is connected to. DNS

entries are usually the same as used by the router's external network configuration

(determined by your ISP). Setting an NTP server will synchronize the Secure NAS

unit to a time server, usually on the Internet. This can be a name or IP address.

Use the keywords “free NTP servers” on your preferred search engine if you wish

to configure this feature and don't know of a server you can use.

When the wizard is complete by either choosing Automatic in Step 1 or completing

Steps 2 and 3, a confirmation page will appear. Clicking the Finish button will apply

the settings.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

View Drive Information

Displays details of all connected drives. If network shares are configured for

drives that have been disconnected, those drives will also appear in this list as

unavailable.

Device: The letter after “sd” is the drive's letter, in order of when the drive was first

encountered by the NAS unit. The number at the end of the device label is the

partition on the drive, in order of the drive's partition map.

Vendor: The drive's manufacturer.

Model: The drive's model number.

Mount Point: Used by the Secure NAS unit internally.

Type: The file system the partition is formatted with.

Size: The total space of the partition.

Used: Space in use on the partition.

Available: Remaining space available on the partition.

% Used: Percentage of the partition space in use.

View User Samba and FTP Login Information

Displays a list of open sessions for file sharing of Windows sharing and FTP. The

session.

Format Drive

Formats a specific drive using a choice of ext3 or XFS file systems.

Caution: this function destroys data.

Choose a drive to format. If the drive is greater than 2TB in capacity choose the

GPT boot record, otherwise choose MBR. Finally, choose Linux EXT3 or Linux

XFS for the file system. After clicking Format Drive, the format utility will request

confirmation.

NOTE: For highest possible performance, use the XFS file system.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

After clicking “Yes, I'm sure,” the format utility will create and prepare one partition

on the selected drive, using all space on the disk. A page will load next confirming

the format is in progress. This page updates once every minute. Once formatting

is complete, the page will change to state it is done. Click any of the tabs above

the message to perform other tasks. If desired, this can be done before formatting

is complete; however, the drive being formatted cannot be used until formatting is

done and there will be no further notifications.

Safely Remove Drive

Closes all pending I/O to a specified drive then “unmounts” it for removal.

Caution: best practice is to notify any and all users this will be done before

proceeding to prevent data loss. Abruptly removing a physical drive without

notifying users or using the Safely Remove Drive function may cause file system

corruption and loss of data.

Backup Internal System Configuration Information

Saves or restores all of the Secure NAS unit's settings using a specified drive.

Select the volume desired for backups. If backups exist on that volume they will be

listed under Backups, with comments if present.

To create a backup, add a backup comment if desired then click Create Backup.

To restore an existing backup, select the desired backup and click Restore

Selected. The currently selected backup may also be deleted using the Delete

Selected button. All three functions will request confirmation before proceeding.

Reboot

Restarts the Secure NAS unit.

Caution: best practice is to notify any and all users this will be done before proceeding

Upgrade the System Firmware

In the case of a firmware update release, this utility applies the update.

Update will not proceed unless only one volume (one partition on one drive) is

present. Instructions on updating firmware are provided with the firmware

update.

Caution: All of the Secure NAS unit's settings will be lost in the process of applying

firmware. Make sure to notify any and all users this will be done to prevent data

loss and use the Backup Internal System Configuration Information utility before

proceeding.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

The Sharing Tab

User Management

Shows current list of known users on the Secure NAS unit.

To delete a user, click the “Delete” link next to that username, then confirm.

To change a user's password, select the username just above “New Password,” then

enter the new password into the “New Password” and “Confirm Password” fields and

click “Change Password.”

To create a new user account, click “New User,” then enter the new username and

the initial password in the “New Password” and “Confirm Password” fields. If shared

folders are defined on the system, select the default permissions granted to the new

user for each share.

Add A Shared Folder

Creates a new folder and shares it on the network. This function has several steps.

The first page introduces the wizard. Click “Begin Wizard” to proceed.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Step 1 is to define the name of the share. The share name will become the folder

name on the drive.

NOTE: The shared folder name will be written to disk using all capital letters. If an existing folder of the same

name appears and is not all capital letters, the Secure NAS considers that not a match and writes the same

folder name in all capital letters anyway. This can cause unpredictable results if the drive is subsequently

connected to a computer. If a folder exists of the same name with all capital letters, it will be shared

without harming any data.

Step 2 is to select the drive the share is to be created on. The drive is identified by the

drive letter and partition number, the vendor and model, and the mount point.

Page is loading ...

Addonics Secure NAS R5 User guide

Brand: Addonics

Model: Secure NAS R5

Category: NAS & storage servers

Type: User guide

Download PDF

report

Addonics Secure NAS R5 User guide

Addonics Secure NAS R5 User guide

Related papers

Other documents