Jenn-Air JGD8130ADS20 Installation guide

Brand: Jenn-Air

Model: JGD8130ADS20

Category: Barbecues & grills

Type: Installation guide

CONVERTIBLEGAS GRILL

COOKTOPSERIES

JGD8130 & JGD8345

=JENN-AIR ,1

403WESTFOURTHSTREET,NORTH• NEWTON,IA 5020

DIMENSIONSSHOWN IN BOTH INCHES AND CENTIMETERS

*Blower may be rotated for horizontal or vertical direction by loosening nuts around blower inlet. Accessible inside ventilation

chamber.

• NOTICE TO INSTALLER: Leave these instructions with the appliance.

• NOTICE TO CONSUMER: Retain these instructions for future reference.

TIEDOWNBOLT

ON EACHEND

BLOWERCANBE GREASE

SWIVELED90° CONTAINER

,--I"1 29" + 1

, 73,66 cm

DUCTINGINSTALLA-

TION INSTRUCTIONS).

T 3 1/2"

8.8 cm

13 13/16"

35.1 cm

2 7/8"

7.3 crn

.Am_

REGULATOR

21" + 1/16"

53,34 cm

7 9/16"

19,21 cm

APPLIANCEPRESSURE

REGULATOR

TIE DOWNBOLT

ON EACHEND

GREASE

BLOWERCANBE CONTAINER

SWIVELED90°

43 1/4" + 1/ 21" + 1/16"

_"_1 109.86 cm , 53.34cm

79/16"

1 7/8"

Min.

'l 15/16" 4,76 cm

Min.

Clearance

2.38 cm

3RIATE _"4f _ ._

(SEE---'

SELECTAPPROPRIATE

DUCTCUT OUT

DUCTINGINSTALLA-

GREASE TION INSTRUCTIONS).

CONTAINER GREASE

r II" \_ "1_ ;l_ _ _ CONTA,NER

[ .

I II I[[F_]_'_'_'_APPLEANCE

PRESSURE 13

FEGULATOR 35 .

3_.9om _o.ooo 7237,8L

INSTRUCTIONSTO INSTALLER

• Dimension "A" - Provide 2" min. (5.08 cm) cabinet clearance to motor for cooling purpose.

• Note - Where possible, 6" (15.24 cm) is recommended for motor/blower service.

• Side Clearance - Grills installed near a side wall must allow a minimum clearance of 8".

• Access must be provided to remove and empty grease container(s).

8101 P580-60

(04-04-00)

InstallingCabinetryOver Your Jenn-Air Grill

*A = 30" (76.2 cm) minimum vertical clearance between

cooking surface and construction above the

appliance.

*B = 13" (33.02 cm) maximum depth of cabinets installed

above cooking top.

t_ i_ mmm

A ÷

Dotted lines

indicate

range hood

construction

* To eliminate associated potential hazards such as

reaching over open flames, avoid use of cabinets above

cooktop for storage space.

CabinetsAbove CookingTop

Maximum depth of cabinets installed above cooking top is

13 inches.

CAUTION: SOME CABINETS AND BUILDING

MATERIALS ARE NOT DESIGNED TO WITHSTAND

THE HEAT PRODUCED BY THE NORMAL SAFE

OPERATION OF A LISTED APPLIANCE.

DISCOLORATION OR DAMAGE, SUCH AS

DELAMINA- TION, MAY OCCUR.

WARNING

THISPRODUCTSHOULDNOT

BE INSTALLEDBELOWA

VENTILATIONTYPEHOOD

SYSTEMTHATDIRECTSAIR

IN A DOWNWARDDIRECTION.

(SEEFIGURE)

THESESYSTEMSMAYCAUSE

IGNITIONAND COMBUSTION

PROBLEMSWITHTHEGAS

BURNERSRESULTINGIN

___j[_ PERSONALINJURYAND MAY

AFFECTTHE COOKING

PERFORMANCEOFTHEUNIT.

ART # 9215-252

NOTE:THE FIGUREMAYNOTACCURATELYREPRESENT

YOUR RANGEORCOOKTOP;HOWEVER,THISWARNING

APPLIESTOALLGASCOOKINGPRODUCTS.

InstallationOf Appliance

Follow accompanying ducting instructions carefully.

This appliance is designed to always be vented outdoors.

The Countertop Cutout, Cabinet Front Cutout and Duct

Opening should be prepared according to the illustrations

on pages 1 and 2.

The installation of this appliance must conform with local

codes or, in the absence of local codes, with the latest

edition of the National Fuel Gas Code, ANSI Z223.1 USA

or current CAN/CGA-B149 INSTALLATION CODE.

This product must be installed by a licensed plumber or

gas fitter when installed within the Commonwealth of

Massachusettsl

A' T handle type manual gas va!ve must be installed in

the gas supply I neto this appliance.

A flexible gas connector; when used, must not exceed a

length of three (3)feet / 36 inches.

The electrical supply required is

110/120 Volt, A.C., 15 amp, 60

Hz. This appliance is equipped

with a grounded tpe power cord.

A grounded outlet must be pro-

vided. It is recommended, for

convenience, this outlet be lo-

cated in the area shown in the

shaded illustration (see figure 2).

Cabinet Bottom

Figure 2

User may experience occasional circuit tripping if Ground

Fault Circuit Interrupter (GFCl) outlet or breaker is in use.

This appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the latest edition of the

National Electrical Code ANSI/NFPA No. 70 USA or

current CSA STANDARD C22.1 Canadian Electrical Code

)art 1.

ELECTRICAL GROUNDING INSTRUCTIONS

IS EQUIPPED WITH

THREE,PRONG GROUNDING PLUG FOR YOUR

PROTECTION AGAINST SHOCK HAZARD

SHOULD BE PLUGGED DIRECTLY INTO A

PROPERLY GROUNDED RECEPTACLE. DO NOT

CUT OR REMOVE THE GROUNDING PRONG FROM

THIS PLUG. .........................

ConnectingApplianceTo Gas Supply

,WARNING

Gas leaks may occur in your system and result in a

dangerous situation. Gas leaks may not be detected by

smell alone. Gas suppliers recommend you purchase and

install an UL approved gas detector. Install and use in

accordance with the manufacturer's instructions.

A QUALIFIED SERVICEMAN OR GAS APPLIANCE

INSTALLER MUST MAKE THE GAS SUPPLY

CONNECTION. Leak testing of the appliance shall be

conducted by the installer according to the

instructions given.

Install a manual shutoff valve in an accessible location in

the gas line external to this appliance for the purpose of

turning on or shutting off gas to the appliance.

Make the gas connection to the inlet to the appliance

pressure regulator on this appliance with a 112" male pipe

thread. Use an approved pipe joint compound resistant to

the action of LP gas at pipe connections. Test all joints for

gas leaks with a soap and water solution or other

accepted leak detection means. Never test for gas leaks

with an open flame.

High Altitude Notice

The specified gas burner ratings typically apply to

elevations up to 2000 feet. For higher altitudes, the rates

may need to be reduced to achieve satisfactory operation.

A local certified gas servicer will be able to advise if a

reduction is necessary.

Apply a non-corrosive leak detection fluid to all joints and

fittings in the gas connection between the supply line

shut-off valve and the range. Include gas fittings and

joints in the range if connections were disturbed during

installation. Check for leaks! Bubbles appearing around

fittings and connections will indicate a leak. If a leak

appears, turn off supply line gas shut-off valve and retest

for leaks. Never test for gas leaks with an open flame.

InstructionsTo Installer

1. Chamfer all exposed edges of decorative laminate to

prevent damage from chipping.

2. Radius corners of cutout and file to insure smooth

edges and prevent corner cracking. Recommend

1/4" or 3/8" diameter drill in each corner.

3. Rough edges, inside corners which have not been

rounded and forced fit can contribute to cracking of the

counter top laminate.

4. Countertop must be supported within 3" of cutout.

Minimum horizontal clearance between the edge of the

appliance and combustible construction extending from

the cooking surface to 18" (45.7 cm) above the cooking

surface is:

15/16" (2.38 cm) at rear

8" at sides

This is not the recommended clearance, but minimum

allowable clearance.

T--

18-

45,7 _)

(

Air Shutter Adjustment

This appliance is shipped from the factory with air

shutters adjusted for use with Natural Gas. If further

adjustment is necessary, or to reset for use with LP,

adjust air shutters as follows:

Grill Burnerand Surface BurnerCartridgeAir

Shutters (SeeIllustrations"A" & "B")

The left hand air shutter controls the rear half of the

burner. The right hand shutter controls the front half.

Access to air shutters on the surface burner cartridge may

be found through openings on the bottom of the cartridge

housing.

Slide air shutters backward or forward to increase or

decrease the size of the air opening. Air shutters fit

snugly, so a screwdriver blade may be required to make

this adjustment (see illustration).

Observe change in flame appearance as the air shutter is

moved. Adjustment is satisfactory when a clearly defined,

even blue flame results at the high flame setting. The

snug fit of the air shutter assures it will remain positioned

correctly.

Grill Burner Air Shutter and Surface Burner

.,___.,. (if so equipped)

:,: "%;"

L sc wo ,w ,.

SLOT AND TWIST WITH SLIGHT

PRESSURE TO ALLOW AIR SHUTTER

TO SLIDE EASILY

On any burner, closing the air shutter too far will cause

the flame to become soft and yellow tipped. Opening the

air shutter too wide will cause the flame to blow away

from the burner ports. Proper adjustment will produce a

sharp, clearly defined, even blue flame.

AIR SHUTTER

Low FlameAdjustment(See Illustration "C")

This appliance is shipped from the factory with low and

medium flame settings adjusted for use with Natural Gas.

If further adjustment is necessary, or to readjust for use

with LP, proceed as follows:

1. Light burner and set control knob for low flame.

2. Remove control knob from valve stem.

NEVER USE A METAL BLADE TO PRY KNOB OFF:

IF KNOB CANNOT BE EASILY REMOVED, TUCK THE

FOLDS OF A CLOTH DISHTOWEL UNDER THE KNOB

AND PULL THE TOWEL UPWARD WITH STEADY

EVEN PRESSURE.

3. Insert a slender, thin-blade screwdriver into the recess

at center of valve stem and engage blade with slot in

adjusting screw.

4. Turn center stem adjusting screw to set flame size.

• clockwise to reduce.

• counterclockwise to increase.

5. Replace control knob when adjustment is completed.

Proper adjustment will produce a stable, steady blue

flame of minimum size. The final adjustment should be

checked by turning knob from high to low several times

without extinguishing the flame.

This adjustment, at low setting, will automatically provide

the proper flame size at medium setting.

CLOCKWISE

TO REDUCE

FLAME SlZE

COUNTERCLOCKWISE TO

INCREASE FLAME SIZE

VALVE

STEM

PressureTesting

The maximum gas supply pressure for the appliance

pressure regulator supplied on this appliance is 14" W.C.

The test pressure for checking this appliance pressure

regulator must be at least 6" W.C. for Natural Gas, and at

least 11" W.C. for LP. It is shipped from the factory set for

Natural Gas at 5" W.C. output pressure.

This appliance and its individual shutoff valve must be

disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in

excess of 112" PSIG (3.5 k Pa).

This appliance must be isolated from the gas supply

piping system by closing its individual manual shutoff

valve during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2" PSIG

(3.5 k Pa).

AppliancePressureRegulatorConversion

(See Illustration "D")

This unit is supplied with a Maxitrol Appliance Pressure

Regulator. Follow the instructions in illustration "D".

MAXITROL APPLIANCE PRESSURE REGULATOR

CONVERTER_I LP

_A CAP I

ND PIN.,..-"

NAT I ..r ,'°

i.J !

APPLY DOWNWARD

FINGER PRESSURE

AT DISC EDGES TO

REPLACE PIN IN CAP

APPLY

_'t k SIDEWARD

FINGER

NAT T PRESSURE TO I LP

I REMOVE PIN i

FROM CAP @

ConversionTo LP Gas

This appliance is shipped from the factory equipped for

use with Natural Gas. To convert it from Natural Gas for

use with LP Gas, perform steps 1 through 4.

1. Remove natural gas orifice hoods. Install color coded

orifice hoods supplied, located in a pack attached to

the outer plenum area of this appliance. (See

Illustration "E", and LP Gas Conversion Instructions on

page 6).

2. Invert cap in convertible appliance pressure regulator (if

so equipped) located at entrance to gas manifold.

3. Adjust air shutters on individual burners for proper

flame appearance.

4. Adjust low flame setting at each burner by turning

adjustment screw in center of valve stem.

To make these conversion adjustments follow the

instructions and illustrations ("A" through "E" on

pages 4 - 5).

This appliance is shipped from the factory with orifice

hoods drilled for use with Natural Gas. To convert from

Natural Gas to LP, apply a 1/2" open-end wrench to hex

section of orifice hood. TURN COUNTERCLOCKWISE

TO REMOVE. Save the Natural Gas orifice hoods just

removed from this appliance for future use. Install color

coded orifice hoods supplied. (See LP Gas Conversion

Instructions above and page 6). TURN CLOCKWISE TO

INSTALL. Hold dimension specified in Illustration "E".

1/2" OPEN END

WRENCH

TURN

COUNTERCLOCKWISE

TO REMOVE

TURN

CLOCKWISE

TO TIGHTEN

ORIFICE HOOD

ControlSettings

The size and type of cookware and the amount and type

of food being cooked will influence the setting needed for

best cooking results. The setting indicated should serve

as a guide while you become familiar with your cooktop.

Use the HI flame setting to /_,_,

quickly bring foods to a boil or /F

to begin a cooking operation. _il_l_,_i_i)_ [ (

Then reduce to a lower __ [ i

setting to continue cooking. _ _,.._1\_

Never leave food unattended _

over a HI flame setting, i

Med setting is used to

continue a cooking opera-

tion. Food will not cook any

faster when a HI flame

setting is used than that is

needed to maintain a gentle

boil. Remember, water boils

at the same temperature

whether boiling gently or

vigorously.

Use Lo setting to keep food

at serving temperatures

without further cooking. You

may find that some cooking

may take place if the

cookware is covered.

MinimumSpacing Requirement

ConvertibleGasCooktops

For installing a Double Bay Downdraft

Cooktop in combination with another

Downdraft Cooktop, the minimum

spacing between adjacent units must

be provided, as shown, for satisfactory

performance.

13/16"

42.2 cm |

3/8"

X/4=_

DOUBLE BAY

TO CONVERTAPPLIANCEFOR USEWITH PROPANEGAS

Natural Gas To PropaneGas (LP) ConversionInstructions

A WARNING

Propane Gas conversion is to be performed by a

Jenn-Air Authorized Service Contractor (or other

qualified agency) in accordance with the

manufacturer's instructions and all codes and

requirements of the authority having jurisdiction.

Failure to follow instructions could result in serious

injury or property damage. The qualified agency

performing this work assumes responsibility for this

conversion.

Models - JGD8130 & JGD8345Series

A WARNING

ELECTRICALPOWERAND GAS MUST BE

TURNEDOFF PRIORTO CONVERSION

Manifold - Propane Gas pressure required - 10" W.C.

Incoming Propane Gas pressure required to appliance

pressure regulator- 11" - 12" W.C.

Propane Gas conversion orifice hoods are supplied with

these models.

Propane Gas input specified - JGD8130/JGD8345 -

33,000 BTU/hr / 51,000 BTU/hr.

TIE DOWN

BOLTON

EACHEND

GREASE

CONTAINER

REGULATOR

BLOWERCAN BE

(_ SWIVELED90"

JGD8345 (Shown)

Left Rear (LR) 7,500 #66 .0330 Zinc

Left Front (LF) 7,500 #66 .0330 Zinc

Right Rear (RR) 9,000 #63 .0370 Blue

Right Front (RF) 9,000 #63 .0370 Blue

Center Rear (CR) 9,000 #63 .0370 Blue

Center Front (CF) 9,000 #63 .0370 Blue

TO CONVERTAPPLIANCEFOR USEWITHNATURALGAS

PropaneGas(LP)ToNaturalGas

Conversion Instructions

If this appliance has been converted for use with LP

Gas, each of the following modifications must be

performed to convert the unit back to Natural Gas.

WARNING

Natural Gas conversion is to be performed by

a Jenn-Air Authorized Service Contractor (or

other qualified agency) in accordance with the

manufacturer's instructions and all codes and

requirements of the authority having jurisdic-

tion. Failure to follow instructions could result

in serious injury or property damage. The

qualified agency performing this work

assumes responsibility for this conversion.

Models - JGD8130& JGD8345Series

Manifold - Natural Gas pressure required - 5" W.C.

Incoming Natural Gas pressure required to appliance

pressure regulator - 6" - 7" W.C.

Natural Gas input specified, Model JGD8130/JGD8345 -

36,000 BTU/hr / 56,000 BTU/hr.

A. Replace all orifice hoods - Perform steps 1 through 4

on page 4. Locate the (4) four or (2) two Natural Gas

hoods (with small numbers stamped on their sides)

saved from the original Natural Gas unit. Page 5

Illustration "E". The two hoods with .0520 (#55 orifice)

stamped on them are for the left front and left rear

burners. The two hoods with the .0550 (#54 orifice)

stamped on them are for the two right burners.

To make these conversion adjustments follow the

instructions and illustrations ("A" through "E")

pages 4 and 5.

B. Invert cap in appliance pressure regulator (see

Illustration "D"). With the appliance installed, the

appliance pressure regulator is located on the center

underside of the appliance at the inlet to the gas

manifold. Identify the type of appliance pressure

regulator on the unit and follow the instructions in the

appropriate illustration.

C. Adjust low flame setting for each burner. Follow the

instructions for burner low flame adjustment on page

4 to increase the simmer flame size.

JGD8345 (Shown)

REGULATOR

TIE DOWN

BOLTON

EACHEND BOXCOVER

GREASE

CONTAINER BLOWERCANBE

SWIVELED90°

BURNER. BTU/hr ORIFICE DIAMETER COLOR

Left Rear (LR) 8,000 #55 .0520 Brass

Left Front (LF) 8,000 #55 .0520 Brass

Right Rear (RR) 10,000 #54 .0550 Brass

Right Front (RF) 10,000 #54 .0550 Brass

Center Rear (CR) 10,000 #54 .0550 Brass

Center Front (CF) 10,000 #54 .0550 Brass

REQUIREDADJUSTMENTSATTIME OF INSTALLATION

The installation of this appliance must conform with local codes, or in the absence of local codes, with

the latest edition of the National Fuel Gas Code ANSI Z223.1 USA or current CAN/CGA-B149 Installation

Code.

This range was manufactured for use with Natural Gas. If LP gas is the fuel of choice, follow the conversion

to LP procedure found in the installation instructions.

Test all external connections for gas leaks. Never test for gas leaks with an open flame.

Test all electrical connections.

Adjust all air shutters for proper flame.

Adjust all valves for low flame settings.

[_ Test the ventilation system for proper installation.

If a problem exists with the downdraft system, check the ducting installation to make sure it conforms to

the Jenn-Air specifications. Most downdraft system problems are attributed to poor ducting practices.

Contact your installer if the ventilation system will not remove smoke or cooking fumes from well trimmed

cuts of meat.

If ventilation problems persist contact your authorized Jenn-Air Service Contractor.

=JENN-AIR

403WESTFOURTHSTREET,NORTH° NEWTON,IA50208

SUPERFICIE PARACOCINAR CON

ASADOR DE GAS CONVERTIBLE

SERIES JGD8130 Y JGD8345

======,,,,,,.,,,,

403WESTFOURTHSTREET,NORTH*NEWTON, IA 50208

LAS DIMENSIONES SE MUESTRAN EN PULGADAS Y CENTiMETROS

* El ventilador puede girarse para colocarlo en posici6n vertical u horizontal aflojando las tuercas de alrededor de la entrada

del ventilador. Camara interior accesible de ventilaci6n.

• AVISO AL INSTALADOR: Deje estas instrucciones con el aparato.

• AVlSO AL CONSUMIDOR: Conserve estas instrucciones para consultarlas en el futuro.

PRESIONDELAPARATO

PERNOpE

SUJECIONEN

CADAEXTREMO

RECIPIENTE DELCABLEADO

ELVENTILADOR DEGRASA

PUEDE GIRARSE 90 ° + 1/16"

29" +1/

73,66 cm 34 cm

8;m

15/16" ! /__

Min.

Espacio

libre

2,38 cm

SELECCIONEEL I

CORTEPARADUCTO

APROPIADO(VEA

LASINSTRUCCIOI_ES

DELA INSTALACION

DEDUCTOS). RECIPIENTE

DE GRASA

t 31_2,,i o \ o

1 8,8cm [ _,

' I II I

_ DELAPARATO

2 7/8" _ _ 13 3/4" _ 11 13/16" -_

7,3 cm 34,9 cm = 30,0 cm

7 9/16"

19,21 cm

PERNOpE

SUJECIONEN

CADAEXTREMO

ELVENTILADOR

PUEDEGIRARSE90°

RECIPIENTE

DEGRASA

REGUI._ADORDE

PRESIONDELAPARATO

CUBIERTADE LACAJA

DELCABLEADO

43 1/4" +1/1 21" +1/16"

109,86 cm 53,34 cm

_ 79/16"

_k_'_. _ 9 3/8" I 1 7/8"

Min.

15/16" _'_"_ 23'81 cm ! 4,76 cm

Min. I '_

Espacio I M "_1

libre I _ / . l

SELECCIONE_

CORTEPARADUCTO /7,x\

APROPIADO(VEALAS_ "

INSTRUCCION,ESDE

LAINSTALACIONDE

DUCTOS). RECIPIENTE

DEGRASA

t 31/2"I _ /

1 8'8cmI /

! _ II I REGULADOR

/ _1 I DEPRESION

_ DELAPARATO

2 7/8" _ _ 13 3/4" -_ 26 3/4"

7,3 cm 34,9 cm 68,0 cm

.A o _

INSTRUCCIONESPARAEL INSTALADOR

• Dimensi6n "A" - Proporcione 2" min. (5,08 cm) de espacio libre del gabinete al motor para

fines de enfriamiento.

• Nota - En donde sea posible, se recomienda un espacio de 6" (15,24 cm) para poder

darle servicio al motor o al ventilador.

• Espacio libre lateral--Los asadores instalados cerca de una pared

lateral deberan tener cuando menos un espacio libre de 8" (20 cm)

• Debe proporcionarse acceso para quitar y vaciar los recipientes de grasa.

Page is loading ...

GRIL A GAZ CONVERTIBLE

SI_RIEPLAQUESDE CUISSON

JGD8130ET JGD8345

403WESTFOURTHSTREET,NORTH NEWTON,IA J

50208, ETATS-UNIS //

DIMENSIONSEN POUCESET EN CENTIMI_TRES

*Le ventilateur peut 6tre tourne pour I'orienter a I'horizontale ou a la verticale en d6vissant les 6crous qui se trouvent sur le

p6rim6tre de I'arriv6e d'air. Accessible a I'int6rieur de la chambre de ventilation.

• NOTE A L'INTENTION DE L'INSTALLATEUR : Veuillez laisser ces instructions avec I'appareil.

• NOTE A L'INTENTION DE L'UTILISATEUR • Veuillez conserver ces instructions pour r6f6rence ult6rieure.

DEL'APPAREIL

BOULOND,E

FIXATIONA,CHAQUE

EXTREMITE DECABLAGE

LEVENTILATEUR BECIPIENT

PEUTPIVOTER A GRAISSE

DE90°

_"'1 29" + 1/

. 73,7cm

CONDUIT(VOIR LES

CONSIGNESDE POSE

DESCONDUITS). _

l 3 1/_"

8,8 cm

13 13116"

35,1 cm

+1/16"

3 cm

RECIPIENT

_, GRAISSE

2 7/8"

7,3 cm

7 9/16"

19,2 cm

13 3/4" _ 11 13/16"

34,9 cm / 30,0 cm

BOULONEE

FIXATIONA CHAQUE

EXTREMITE

DETENDEUR

DEUAPPAREIL

DECABLAGE

LEVENTILATEUR BI_CIPIENT

PEUTPIVOTER AGRAISSE

DE90°

43 1/4"+ 1/ 21" + 1/16"

,__,._ ]09,9cm 53,3cm

9 3/8" 17/8"

8 cm rain.

15/16"min. 4,8cm

D6gagement

2,4crn

SI_LECTIONNER_E

DECOUPE QUI

CONVIENT POUR _ "

CONDUIT(VOIR LES

CONSIGNESDE POSE

DESCONDUITS). I_ECIPIENT

A GRAISSE

3 1/2"

8,8 cm

1313/16,,I I _ I_."

35,1 cm

2 7/8" 13 3/4" 26 3/4"

7,3 cm 34,9 cm 68,0 cm

CONSIGNESA L'INTENTIONDE L'INSTALLATEUR•

• Dimension <<A >>- Prevoir 2 po min. (5,1 cm) de d6gagement par rapport a I'armoire pour permettre le

refroidissement du moteur.

• Note - Chaque fois que cela est possible, un degagement de 6 po (15,2 cm) est recommande pour

permettre I'acces au moteur/ventilateur en cas de panne.

• Degagement sur le c6te - Les gril montes pres d'une cloison laterale doivent avoir un

degagement de 8 po (15,2 cm) minimum.

• L'acces dolt 6tre prevu afin de permettre de retirer et de vider le ou les recipients

graisse.

Page is loading ...

Jenn-Air JGD8130ADS20 Installation guide

Brand: Jenn-Air

Model: JGD8130ADS20

Category: Barbecues & grills

Type: Installation guide

Download PDF

report

in other languages

français: Jenn-Air JGD8130ADS20 Guide d'installation
español: Jenn-Air JGD8130ADS20 Guía de instalación

Jenn-Air JGD8130ADS20 Installation guide

Jenn-Air JGD8130ADS20 Installation guide

in other languages

Related papers

Other documents