SHANGRI-LA SLLEDBEDBDA LED Gas Lift Bed Frame

SHANGRI-LA SHANGRI-LA SLLEDBEDBDA LED Gas Lift Bed Frame User guide

  • Hello! I've reviewed the user guide for the SHANGRI-LA Bed Frame SLLEDBEDBDA. This guide details the assembly process for your new bed frame, including the installation of the LED light strip, gas lift mechanism, and slat support system. I'm ready to assist you with any questions you have about assembling your bed.
  • What should I do if components are missing?
    How should the surface be cleaned?
    What should the user do when they receive the product with flaws?
LED GAS LIFT BED FRAME
(DOUBLE)
SLLEDBEDBDA
Ensure to read all instructions and warnings in this user guide prior to assembly.
When opening the packaging, ensure all components are accounted for. If
components are missing, contact help.Kogan.com for assistance.
Clean the surface using only with a slightly damp cloth, do not use strong abrasive
cleaners.
Using mismatched or incorrect hardware may cause damage to the product. Identify
all the hardware and accessories prior to installation.
Note: The leather fabric tends to get dirty during the packing process, if you receive
the item a little flaw, you can wipe it clean with the wet wipes. If there have any
problem, please do feel free to contact us.
A Headboard (x1)
B Footboard (x1)
C Right sideboard
(x1)
D Left sideboard
(x1)
E Long slat
support (x2)
F Short slat
support (x2)
G Centre slat
support (x1)
H Support leg (x2)
SAFETY & WARNINGS
COMPONENTS
Hardware
1 Bed base fabric (x1)
2 Feet (x4)
3 M8x20 (x24)
4 M8 Washer
(x14)
5 Bracket (x2)
6 Allen Key
7 T-handle Allen
Key
8 M8x40 Screw
(x14)
9 M8 Nut (x22)
10 Remote receiver (x1)
11 Remote (x1)
12 End Caps
(x22)
13 Slats (x22)
14 Inner Caps (x11)
15 Lift handle (x1)
16 Mattress
stopper (x1)
19 Alcohol wipe (x1)
20 Power adapter (x1)
Step 1
Screw the feet (2) to the headboard (A) and footboard (B).
Insert x8 M8x20 screws (3) into the headboard and footboard.
2
Feet (x4)
3
M8x20 (x8)
ASSEMBLY
Step 2
Align the holes on the ends of the footboard (B) with those on the left and right
sideboards (C, D).
Align a bracket (5) with the corner between the left sideboard (C) and footboard (B),
then use the Allen key (6) to secure the bracket (5) with x4 M8x20 screws (3).
Repeat the same process on the corner between the right sideboard (D) and footboard
(B).
3
M8x20 (x8)
5
Bracket (x2)
Step 3
Connect the x4 frames (E,F) using the M8x20 screws (3), pay attention to the
orientation of the left and right-side tube (E).
Connect the centre support bar (G) to the assembled frame using M8x40 screws (8)
and M8 washers (4) on the outside of (F) and secure it with x4 M8 nuts (9).
Install the support legs (H) to centre bars (G) in the same way, and then tighten it using
the Allen key (6) and T-handle Allen key (7).
3
4
8
9
Step: 4
Place the slat support assembly onto the gas lifts (on the sideboard) and secure it in
place using x6 M8x40 screws (8), x6 M8 washers (4), and x6 M8 nuts (9) in the holes.
Tighten using the Allen key (6) and T-handle Allen key (7) to secure the screws.
4
M8 washer (x6)
8
M8x40 screws (x6)
9
M8 nuts (x6)
Step: 5
Install the lift handle (15) and mattress stopper (16) to the bed.
15
Lift handle (x1)
16
Mattress stopper (x1)
Step: 6
Connect 2 slats (13) together using x1 inner caps (14) and x2 end caps (12) to create a
slat assembly. Repeat this process for the remaining slats (13).
Secure the slat assemblies by aligning the holes on the end caps (12) and inner caps
(14) with the slots on the bed assembly.
12
End caps (x22)
13
Slats (x22)
14
Inner caps (x11)
12
13
14
13
12
x11
Step: 7
Extend the gas struts (18) on the left and right sideboards (C, D), then tighten the screws.
Step: 8
Connect the remote receiver (10) to the light strip (17).
Connect the power adapter (20) to the remote receiver (10).
10
Remote receiver (x1)
17
Light strip (x1)
20
Power adapter (x1)
Power adapter
Remote receiver
Remote
Light strip
Step: 9
Place the bed base fabric (1) onto the bed assembly.
Attach the strip light (17) to the channel on the outside of the sideboard and footboard.
Tighten all screws using the Allen key (6) and T-handle Allen key (7). Clean the bed
using the alcohol wipe (19).
1
17
19
Remote button controls
The remote is used to control the LED light strip. Refer to the table below for the function of
each button:
Brightness +
(Speed up)
Brightness -
(Speed down)
Off
On
Static red
Static green
Static blue
Static white
Static orange
Static pea-green
Static dark blue
7 colours jump
change
Static dark yellow
Static cyan
Static brown
All colours fade in
& fade out
Static yellow
Static light blue
Static pink
7 colours fade
change
Static straw
yellow
Static sky blue
Static purple
3 base colours
jumpy
OPERATION
NOTES
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com.
1/16