2. UPLIFT Desk
  3. T-Frame
T-Frame

UPLIFT Desk T-Frame Operating instructions

  • Hello! I've reviewed the UPLIFT DESK side bracket attachment instructions for C-Frame and T-Frame desks. This document provides detailed steps for assembling the side brackets and logo plates, and lists components such as feet, side brackets, logo plates, and screws. I'm ready to answer your questions about the assembly process.
  • What are the SKUs for which this instruction sheet is needed?
    What should I do if my Core 1 frame box is labeled with FRM500 or FRM550?
    What components are included in the C-Frame Feet & Side Brackets Box?
®
Side Bracket Attachment Instruction
(C-Frame and T-Frame)
T-Frame Feet & Side Brackets Box Components
Side
Bracket
(qty 2)
Foot
(includes Leveling
Glides, qty 2)
P3
P2P1
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
T-Frame
Crossbar End
Adapter
(right and left qty 2)
M8x10
Machine Screw
(qty 4)
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
H7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
Logo
Plate
(qty 2)
P16 M6x10
Machine Screw
(qty 4)
H1
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C-Frame Feet & Side Brackets Box Components
Side Bracket
(right and left, qty 2)
Logo Plate
(qty 2)
Foot
(includes Leveling Glides, qty 2)
P2 P16P1
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
M6x10
Machine Screw
(qty 4)
H1
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
Side Bracket Attachment
A. Slide the tabs of the Side Brack-
et (P2) into the Crossbar End (P5)
and insert two Machine Screws (H1)
through the top of the Crossbar End
as shown. Loosely start each screw
by hand, but do not tighten them
completely.
IMPORTANT, PLEASE READ:
If your Core 1 frame box is labeled with either of the following SKUs, you will need to use this in-
struction sheet for the side bracket attachment section.
• FRMA-2-SRD-CORE1
• FRMA-3-SRD-CORE1
If your Core 1 frame box is labeled with either of the following SKUs, you can discard this instruc-
tion sheet and use the instructions received in your Core 1 frame box.
• FRM500
• FRM550
P5
H1
P2
AI-FRM50X-1.040032393v.A
Side Bracket Attachment (Continued)
B. Insert two more Machine Screws (H1) through the two larger holes in the face of the Side Bracket (P2)
and into the Leg. Loosely start each screw by hand, but do not tighten them completely.
C. Once all four screws (H1) are started, tighten them completely.
D. Attach the Logo Plate (P16) by pressing the posts on the Logo Plate rmly into the two smaller holes
in the side of the Side Bracket. The Logo Plate conceals the two screws in the face of the Side Bracket.
When assembling the Legs in the orientation shown, the Logo Plate will need to be attached upside-
down so that it is right-side-up when the desk is ipped over.
F. Repeat these steps for the second Leg assembly.
H1
P16
/