KOGEL Sram Red and Force eTap AXS Oversized Derailleur Cage User manual

Brand: KOGEL

Model: Sram Red and Force eTap AXS Oversized Derailleur Cage

Type: User manual

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

WHAT’S IN THE BOX

Kolossos for SRAM eTap AXS Cage and Pulleys

Kogel eTap AXS tool

Loctite

Kogel stickers

Manual link card

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

TOOLS NEEDED FOR THIS INSTALLATION:

• Torx T10

• 2mm allen

• 5mm allen

• Felt tip pen

• Phillips screwdriver

• Chain tool

• Light grease

• New chain, since the Kolossos cage requires

a few extra links compared to the stock setup

STEP 1:

Shift the derailleur to the lowest gear or the largest

cog position. With the bike secure in the stand, remove

the chain.

STEP 2:

Remove the rear wheel.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 4:

Remove the pulleys.

STEP 5:

Remove the back cage.

STEP 3:

Remove the derailleur.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 7:

Use Kogel eTap AXS tool to remove

the front cage. Loosen the bolt 1 1/4 turn.

STEP 8:

After loosening the bolt, unwind the

spring tension, then remove the bolt

completely.

STEP 6:

Remove the rotation stop pin from the

front cage.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 10:

Disassemble the Kolossos overized cage. Start with the

stop pin.

STEP 11:

Then release all bolts on the backside

and dissasemble.

STEP 9:

Keep the mounting bolt and spring aside to be reused.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 13:

Once secure all the way set aside the cage. With a felt

tip mark identify the ﬂat edge. Place a mark on the

rounded face identiﬁng the edge that’s ﬂat.

STEP 14:

Reinstall the spring in the derailleur body.

STEP 12:

Use the front cage to reset the position of the clutch

system in the derailleur body. Line up the D-shape on

the pulley cage with the D-shape inside the derailleur

body.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 16:

Install the nut and tighten it a few revolutions, less

than ﬁnger tight.

STEP 17:

Load the spring tension by pivoting the front cage

clockwise around the center nut one revolution.

STEP 15:

Install the front cage. Align the spring with the the

center hole to set the recommended tension.

Use the forward hole (near the rotation stop pin) for

higher spring tension and security on rough terrain. Use

the backward hole for lowest possible friction: useful

for a time trial on smooth surface.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 19:

Install the rotation stop screw. Tighten to 3Nm.

STEP 20:

Install pulley wheels. “U” indicates upper pulley. “L”

indicates lower pulley. Make sure “U” and “L” are facing

outward when mounted on the frame.

STEP 18:

Align and engage the D-shape, then tighten the nut

to 6Nm. Check if the cage and clutch move freely for

operation.

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 22:

Install the derailleur back on the bike.

STEP 23:

Install rear wheel.

STEP 21:

Install back cage. Use Loctite and install

all bolts with Loctite. Torque setting,

less than 1Nm

KOGEL.CC USA: +1 915 777 5666 info@kogel.cc

INSTALLING KOLOSSOS FOR SRAM eTap AXS and Rival

KOLOSSOS: INSTALLATION MANUAL

STEP 25:

Adjust the derailleur position, upper and lower limit and

b-tension as per Sram’s instructions.

STEP 26:

Adjusting the B-tension: the gap between the largest

cog and the upper pulley should be the same as Sram’s

recommendation for the standard cage. The Sram

supplied gauge will not ﬁt the oversized 14 tooth pulley.

Below are the recommended gaps between the top of

the pulley and largest cog for each cassette size:

26T: 15mm

28T: 10mm

33T: 6mm

36T: 6mm

STEP 24:

Install the new chain over the small ring, smallest cog.

Chain length is correct if there is a minimal tension on

the cage.

KOGEL Sram Red and Force eTap AXS Oversized Derailleur Cage User manual

Brand: KOGEL

Model: Sram Red and Force eTap AXS Oversized Derailleur Cage

Type: User manual

Download PDF

report

KOGEL Sram Red and Force eTap AXS Oversized Derailleur Cage User manual

KOGEL Sram Red and Force eTap AXS Oversized Derailleur Cage User manual

Related papers

Other documents