2. Jabra
  3. Engage 75
Engage 75

Jabra Engage 75 User manual

  • Hello! I've reviewed the user manual for the Jabra Engage 75 Convertible and Engage 65 headsets. This document details how to connect these headsets to Aastra desk phones for remote call control, including cable connections, software info and settings. I'm ready to answer any questions you have about setting up your headset or its features as described in the document provided.
  • What is needed to connect Jabra Engage to Aastra desk phone?
    How do I connect the headset to the desk phone?
    How do I initially configure the Jabra Engage 75 headset?
    How do I initially configure the Jabra Engage 65 headset?
    How do I activate DHSG mode on Aastra desk phone?
    What audio mode should I set on the phone?
    What is recommended microphone volume setting?
Jabra Engage 75 Convertible
How do I connect my Jabra Engage with my Aastra 53i, 55i, 57i,
6753i, 6755i, 6757i desk phone so I have remote call control
using my headset?
Prerequisites
Jabra Link 14201-10 electronic hook switch (EHS) cable
DHSG connection cable from Aastra
Aastra 53i / 55i / 57i / 57iCT / 6753i / 6755i / 6757i / 6757iCT phone
with firmware version 2.5.1.2000 or later
To connect your headset:
1. Plug the RJ10 connector (green) from the split end of the Aastra DHSG
cable into the headset socket/port on the desk phone.
2. Plug the RJ45 connector (yellow) from the split end of the Aastra
DHSG cable into the socket/port for the expansion module on the desk
phone.
3. Plug the single end of the Aastra DHSG cable (blue) into the Aastra
RJ45 adapter.
4. Plug the single end of the Jabra Link 14201-10 cable (blue) into the
free socket on the Aastra RJ45 adapter.
5. Connect the 2-sided end of the Jabra Link 14201-10 cable to the Jabra
base as follows:
a. Plug the RJ10 (small) connector into the socket/port with the blue
22/08/2022 22:19
https://www.jabra.com.au/supportpages/jabra-engage-75/9555-583-117/faq/e23aaa3c-
7d2d-447d-a66f-cd2caf4dd02e
Page 1 of 3
phone icon.
b. Plug the RJ45 (wide) connector into the socket marked AUX.
To configure your headset when connecting to a desk phone for the first
time:
For the Jabra Engage 75, follow the onscreen setup wizard on the base.
For the Jabra Engage 65, the initial setup is complete after connecting
the cables.
See the user manual located in the Technical Documents section for more
details about setting up the desk phone.
Use Jabra Direct, the computer application that is available free of charge,
to learn more about your Jabra product. Use Jabra Direct to adjust
features and functions according to personal preference or company
requirements. Also ensure your Jabra product is updated to get the latest
performance. Visit jabra.com/direct for more information.
Note:
Additional setup information for your Jabra products:
EHS cable/adapter type: DHSG.
Clear dial tone switch: set to position “A”.
We recommend setting the microphone volume to "7" out of 13.
Phone settings:
1. For Aastra desk phones with firmware version 2.5.1.2000, the DHSG
mode is deactivated by default. Activate it by using Aastra.cfg or
mac.cfg with the command “dhsg:1”.
2. Make sure you set the audio mode to “Headset/Speaker". Access the
phone settings by navigating to Options>Default settings>Audio
settings>Audio mode>Headset/Speaker.
22/08/2022 22:19
https://www.jabra.com.au/supportpages/jabra-engage-75/9555-583-117/faq/e23aaa3c-
7d2d-447d-a66f-cd2caf4dd02e
Page 2 of 3
Note:
There is no possibility for remote call control if you are using an expansion
keypad.
22/08/2022 22:19
https://www.jabra.com.au/supportpages/jabra-engage-75/9555-583-117/faq/e23aaa3c-
7d2d-447d-a66f-cd2caf4dd02e
Page 3 of 3
/