Altronix SMP5CTX Installation guide

Type
Installation guide

Altronix SMP5CTX is a power supply/charger that can convert 115VAC or 230VAC input into a regulated 12VDC or 24VDC output, providing continuous load current up to 4A. It features selectable output voltage, built-in charger for sealed lead acid or gel type batteries, and various protection mechanisms against short circuits and thermal overload. The SMP5CTX also includes visual indicators for AC input and DC output status, making it suitable for various security and access control applications, such as powering surveillance cameras, door strikes, and electric locks.

Altronix SMP5CTX is a power supply/charger that can convert 115VAC or 230VAC input into a regulated 12VDC or 24VDC output, providing continuous load current up to 4A. It features selectable output voltage, built-in charger for sealed lead acid or gel type batteries, and various protection mechanisms against short circuits and thermal overload. The SMP5CTX also includes visual indicators for AC input and DC output status, making it suitable for various security and access control applications, such as powering surveillance cameras, door strikes, and electric locks.

Rev. 093003 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
SMP5CTX Series
Power Supply/Chargers
Models Include:
SMP5CTX
SMP5PMCTX
SMP5PMCTXX
- Single Output.
SMP5PMP4
- Four (4) Fuse Protected Outputs.
SMP5PMP8
- Eight (8) Fuse Protected Outputs.
SMP5PMP16
- Sixteen (16) Fuse Protected Outputs.
SMP5PMP4CB
- Four (4) PTC Protected Outputs.
SMP5PMP8CB
Eight (8) PTC Protected Outputs.
SMP5PMP16CB
- Sixteen (16) PTC Protected Outputs.
Installation Guide
- 2 - SMP5CTX Series Installation Guide
Overview:
Altronix SMP5CTX Series power supply/chargers convert a 115VAC or 230VAC, 50/60Hz input into a regulated
12VDC or 24VDC output up to 4A of continuous load current (see specifications).
SMP5CTX Series Power Supply Configuration Reference Chart:
Altronix
Model Number
Accessory
Power
Distribution
Module(s)
Number
of Outputs
Fused Outputs
PTC Outputs
(auto-resettable)
Individual
Output
Rating (A) Supervised
115VAC/
230VAC
Input
Current
(A)
12/24VDC
Total
Output
Current
(A)
SMP5CTX
1 – – 4A
0.95A/
0.5A 4A
SMP5PMCTX
P
SMP5PMCTXX
SMP5PMP4 PD4 4P– 3.5A
SMP5PMP4CB PD4CB P2.5A
SMP5PMP8 PD8 8P– 3.5A
SMP5PMP8CB PD8CB P2.5A
SMP5PMP16 PD16W 16 P– 3.5A
SMP5PMP16CB PD16WCB P2.5A
Specifications:
Power Supply Voltage Output Specifications:*
Output VDC Switch Position Max. Load DC
12VDC SW1 - ON (Fig. 1c, pg. 5) 4A
24VDC SW1 - OFF (Fig. 1c, pg. 5) 4A
*Specified at 25˚C ambient.
ON
OFF - 24V
ON - 12V
Agency Listings:
CE European Conformity.
Input:
Input 115VAC, 50/60Hz, 0.95A or
230VAC, 50/60Hz, 0.5A.
Output:
12VDC or 24VDC selectable output.
4A supply current.
Filtered and electronically regulated outputs.
Short circuit and thermal overload protection.
Battery Backup:
Built-in charger for sealed lead acid or
gel type batteries.
Maximum charge current 0.5A.
Zero voltage drop when switching over to
battery backup.
Visual Indicators:
AC input and DC output LED indicators.
Features:
Power ON/OFF switch.
Supervision (select models):
AC fail supervision (form “C” contacts).
Low battery supervision (form “C” contacts).
Electrical:
• Operating temperature: 0ºC to 49ºC ambient.
Mechanical:
• Enclosure Dimensions (H x W x D approx.):
SMP5CTX, SMP5PMCTX, SMP5PMP4,
SMP5PMP4CB, SMP5PMP8, SMP5PMP8CB,
SMP5PMP16, SMP5PMP16CB:
13.5” x 13” x 3.25”
(342.9mm x 330.2mm x 82.6mm)
- Accommodates up to
two (2) 12VDC/7AH batteries.
SMP5PMCTXX:
15.5” x 12” x 4.5”
(393.7mm x 304.8mm x 114.3mm)
- Accommodates up to
two (2) 12VDC/12AH batteries.
SMP5CTX Series Installation Guide - 3 -
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all
local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws; level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pgs. 7, 8). Secure enclosure to earth ground.
2. Slide [Power ON/OFF] switch t o OFF position.
3. Set SW1 on the power supply board to the desired DC output voltage (Fig. 1c, pg. 5)
(Power Supply Voltage Output Specification Chart).
4. Connect AC power to the terminals marked [L & N], connect ground to the green flying lead (Fig. 1, pg. 5).
Use 18 AWG or larger for all power connections (Battery, DC output).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
5. Slide [Power ON/OFF] switch to ON position.
6. Measure output voltage before connecting devices. This helps avoiding potential damage.
Keep power-limited wiring separate from non power-limited wiring (115/230VAC, 50/60Hz Input,
Battery Wires). Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts.
Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside.
Refer installation and servicing to qualified service personnel.
7. Slide [Power ON/OFF] switch t o OFF position.
8. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 2, pg. 6), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 3, pg. 6),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 4, pg. 6), carefully observing correct polarity.
Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board (Fig. 1a, pg. 5).
When servicing the unit, AC mains should be removed.
9. When using stand-by batteries, they must be lead acid or gel type.
Connect battery to the terminals marked [– BAT +] (battery leads included).
12VDC operation: Use one (1) 12VDC battery.
24VDC operation: Use two (2) 12VDC batteries connected in series.
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
For supervised models only:
10. Connect appropriate signaling notification devices to AC Fail and Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1b, pg. 5).
11. Slide [Power ON/OFF] switch to ON position.
LED Diagnostics:
Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery is supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Power Distribution Module
Green Power Distribution Module Status
ON Normal operating condition.
OFF No Power Output.
- 4 - SMP5CTX Series Installation Guide
Terminal Identification:
Power Supply Board:
Terminal Legend Function/Description
L, G, N Connect 115VAC/230VAC to these terminals: L to Hot, N to Neutral.
DC + 12VDC / 24VDC @ 4A continuous output.
*AC FAIL
NC, C, NO
Used to notify loss of AC power, e.g. connect to audible device or alarm panel.
Relay normally energized when AC power is present.
Contact rating 1A @ 120VAC / 28VDC.
*Low Battery
NC, C, NO
Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally
energized when DC power is present. Contact rating 1A @ 120VAC / 28VDC.
Low battery threshold:
12VDC output threshold set @ approximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
BAT + Stand-by battery connections. Maximum charge rate 0.5A.
*Note: Supervised models only
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module:
Terminal Legend Function/Description
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
SMP5CTX Series Installation Guide - 5 -
LGN
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
5A 250V
OFF - 24V
ON - 12V
ON
--- BAT + --- DC +
AC DC
Power Supply
Board
Green
Lead
115VAC/
230VAC
power
mains Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LGN
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
5A 250V
OFF - 24V
ON - 12V
ON
--- BAT + --- DC +
AC DC
Power Supply
Board
Green
Lead
115VAC/
230VAC
power
mains Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LGN
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
5A 250V
OFF - 24V
ON - 12V
ON
--- BAT + --- DC +
AC DC
Power Supply
Board
Green
Lead
115VAC/
230VAC
power
mains Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LGN
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
5A 250V
OFF - 24V
ON - 12V
ON
--- BAT + --- DC +
AC DC
Power Supply
Board
Green
Lead
115VAC/
230VAC
power
mains Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
Fig. 1b
See
LED Diagnostics,
pg. 3
Fig. 1
Fig. 1a
Switch disables power mains line voltage input.
If stand-by battery (batteries) are connected, the DC output remains on
Fig. 1c
SW1
12VDC - ON
24VDC - OFF
- 6 - SMP5CTX Series Installation Guide
INPUT
LED
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1 F2 F3 F4
COMMON POWER OUTPUTS
1P 1N 2P 2N 3P 3N 4P 4N
DC Output to devices From Power Supply
Board
(Factory Installed)
Used on
PTC Models
N
COMMON POWER OUTPUTS
P
FUSED POWER OUTPUTS
1 2 3 4 5 6 7 8
D1
INPUT
R1 LED
ON OFF
SW1
Used on
PTC Models
DC Output to devices From Power Supply
Board
(Factory Installed)
Power Distribution Module(s):
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
9 10 11 12 13 14 15 16
PN
3.5A 250V
For continuous protection against risk of fire
replace fuses with same type and rating.
Used on
PTC Models
Fig. 2 - PD4/PD4CB
Fig. 3 - PD8/PD8CB
Fig. 4 - PD16W/PD16WCB
SMP5CTX Series Installation Guide - 7 -
Enclosure Dimensions (BC300):
SMP5CTX, SMP5PMCTX, SMP5PMP4, SMP5PMP4CB,
SMP5PMP8, SMP5PMP8CB, SMP5PMP16, SMP5PMP16CB
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
Enclosure accommodates up to two (2) 12VDC/7AH batteries.
Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix).
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)
- 8 - SMP5CTX Series Installation Guide
Enclosure Dimensions (BC400):
SMP5PMCTXX
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
Enclosure accommodates up to two (2) 12VDC/12AH batteries.
1.5”
(38.1mm)
1.5”
(38.1mm)
4.615” (117.2mm) 4.615” (117.2mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
4.615” (117.2mm) 4.615” (117.2mm)
1.75”
(44.5mm)
1.75”
(44.5mm)
1.375”
(34.9mm)
1.125”
(28.6mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
5.0” (127.0mm)
5.0” (127.0mm)
4.5” (114.3mm)4.5” (114.3mm) 1.25”
(31.8mm)
1.25”
(31.8mm)
0.79” (20.1mm)0.91”
(23.1mm)
0.91”
(23.1mm)
15.5” (393.7mm)
1.1”
(27.9mm)
1.1”
(27.9mm)
1.1”
(27.9mm)
12.23” (310.6mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
1.25” (31.8mm)1.25” (31.8mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IISMP5CTX Series F18U MEMBER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Altronix SMP5CTX Installation guide

Type
Installation guide

Altronix SMP5CTX is a power supply/charger that can convert 115VAC or 230VAC input into a regulated 12VDC or 24VDC output, providing continuous load current up to 4A. It features selectable output voltage, built-in charger for sealed lead acid or gel type batteries, and various protection mechanisms against short circuits and thermal overload. The SMP5CTX also includes visual indicators for AC input and DC output status, making it suitable for various security and access control applications, such as powering surveillance cameras, door strikes, and electric locks.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI