INSTALLATION MANUAL
EE-IR-RCVR-SM
EE-IR-RCVR-TT
EE-IR-RCVR-TUBE
PRODUCT OVERVIEW
Welcome to Episode®. This product is engineered to provide years of exceptional
reliability. We appreciate your business, and we stand committed to providing our
customers with the highest degree of quality and service in the industry.
PACKAGE CONTENTS
• 1x IR Receiver
• 1x Washer (Tube only)
• 1x 3.5mm to 3-pin Male Screw Terminal Adapter
• 1x 3.5mm to 3-pin Female Screw Terminal Adapter
• 2x Adhesive Strips (SM/TT models only)*
• 1x Installation Manual
NOTE: Adhesive strips for the TT model are stored inside of the plastic housing.
See 3.1.1 for details on converting a EE-IR-RCVR-TT to EE-IR-RCVR-SM.
SETUP
EE-IR-RCVR-SM/TT Placement
Determine the best location for the IR Receiver. The IR Receiver should be placed
so that it does not directly face other light sources such as lamps or displays
(standard, LCD, or plasma).
Ensure that this location is within the distance parameters of the IR Receiver.
Convert EE-IR-RCVR-TT to EE-IR-RCVR-SM
1. Remove the screw and open the plastic housing.
2. Remove the module and adhesive strips inside to use as a surface-mount
IR Receiver.
EE-IR-RCVR-TUBE Mounting
Drill a 1/2" hole in any surface, such as a cabinet panel. Pass the lead and body of the
EE-IR-RCVR-TUBE through the hole, and secure from the rear with the supplied nut.
Screw
Plastic Housing
Bottom View
page | 2
© 2016 Episode®
CONNECT
Standard Wiring
Connect the IR Receiver to an IR Repeater, or any device with an IR Receiver input.
EMITTERS
POWER
SIGNA
L
+1
2V GN
D
IR RECEIVER IN
POWE
R
+1
2VD
C
1 2 3 4
IR Connection
IR Receiver Input
Device with
Block
RIM
O
INPUT 4 INPUT 5 INPUT 6
1 2
3
6 87
Engineered in the U SA
Manufactured in T aiwan
SY ST EM
IR R eceiver ALL IR O ut
EE-IR-RCVR-TUBE
EE-IR-RCVR-SM/TT
Note: Do not connect the IR Receiver to an IR Emitter connection as it may dam-
age the IR Receiver.
IR Repeater Screw Terminals
When using an IR Repeater, the IR Receiver can be connected to the screw
terminals by removing the 3.5mm (1/8”) connector. When this method is used,
proper polarity must be maintained in order to ensure proper operation.
POWE
R
SIGNA
L
+1
2
V GN
D
GND
12V DC
IR Signal
Note: White Stripe
To Screw Terminals
EE-IR-RCVR-TUBE
EE-IR-RCVR-SM/TT
page | 3
© 2016 Episode®
Extending the Cable
Attach or extend the wire using the provided adapters. Proper polarity must be
maintained in order to ensure proper operation. Wire pinouts are displayed below
for reference.
IR Signal (Tip)
12V DC (Sleeve)
GND (Ring)
GND (Ring)
12V DC (Sleeve)
IR Signal (Tip)
Note White Stripe
Note: When using long lengths of cable (>50 ft), it may be necessary to connect
a 470 Ohm 1/8 Watt resistor between the “IR IN” (signal) and “GND”. The resistor
discharges the cable capacitance, which allows high bit-rate IR codes to work
with higher reliability.
SIGNA
L
+1
2V GN
D
GND
12V DC
IR Signal
IR Connecting Block
Terminals
470 Ohm 1/8 Watt
Resistor
IR Signal (Tip)
12V DC (Sleeve)
GND (Ring)
IR Block
Male AdapterFemale Adapter
Cable Extension
EE-IR-RCVR-TUBE
EE-IR-RCVR-SM/TT
POWER
SI
G
N
A
L
+
1
2V GN
D
IR R
E
CE
I
VER I
N
POWE
R
+
1
2VD
C
White Stripe
GND (Ring)
12V DC (Sleeve)
IR Signa
l
(Tip)
Ring (R): Ground
Sleeve (S): 12V DC
Tip (T): Signal
S
R
T
page | 4
© 2016 Episode®
SPECIFICATIONS
Power +12VDC @ 25mA
Maximum Recommended
Cable Length
1000' with CAT 5 cables
Carrier Frequency
Acceptable Range
30kHz to 60kHz
Control Range 4' to 40' without speaker grille
2' to 28' with speaker grille
*Actual range depends on signal strength and
ambient noise conditions.
Control Angle 0+/- 45° off axis
Dimensions
EE-IR-RCVR-TABLE 0.86" H x 3" W x 1.42" D
EE-IR-RCVR-SURFACE 0.68" H x 2.55" W x 0.39" D
EE-IR-RCVR-TUBE 0.63" W x 1.46" D
DIMENSIONS
page | 5
© 2016 Episode®
3"
1.37"
2.55"
1.42"
1.46"
0.86"
EE-IR-RCVR-TABLE
EE-IR-RCVR-SURFACE
EE-IR-RCVR-TUBE
0.675"
0.385"
0.47"
0.63"
0.59"
WARRANTY
3-Year Limited Warranty
Episode® Electronics products have a 3-Year Limited Warranty. This
warranty includes parts and labor repairs on all components found
to be defective in material or workmanship under normal conditions
of use. This warranty shall not apply to products that have been
abused, modified, or disassembled. Products to be repaired under
this warranty must be returned to a designated service center with an
assigned return authorization (RA) number. Contact technical support
for an RA number.
CONTACTING TECHNICAL SUPPORT
866.838.5052
Rev: 160106-1120
-
1
-
2
-
3
-
4
-
5
-
6
Episode EE-IR-RCVR-TUBE Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
No Drilling Required DK220-CHR Installation guide
-
Xantech 490-95 User manual
-
Sonance CB1 User manual
-
Xantech 789-44 Installation guide
-
Proficient Audio Systems ONE Owner's manual
-
-
-
Binary B-600-EXT-330-RS-IP Installation guide
-
-
