Norpole NPGR2-B Installation guide

Type
Installation guide

This manual is also suitable for

GLASS DOOR MERCHANDISERS
COMMERCIAL REFRIGERATOR AND FREEZER
USER’S MANUAL
GLASS DOOR MERCHANDISERS
PLEASE READ THE MANUAL THOROUGHLY PRIOR TO
EQUIPMENT SET-UP, OPERATION AND MAINTENANCE.
1
Model: NPGR1-S9B, NPGR1-S, NPGR1-SB, NPGR2-S, NPGR2-SB,
NPGR3-S, NPGR3-SB, NPGR2, NPGR2-B
GLASS DOOR MERCHANDISERS
INSTALLATION
The refrigeration system operates most efficiently when installed in an area
with cool, dry air circulation.
There must be at least 6 inches of clearance on both sides and the back of
the cabinet.
Select a location away form the heat and moisture generating equipment
such as stoves, ovens, etc.
Avoid direct sun rays.
Be sure that the floor where you intend to install the unit is strong and level
enough to support the total weight of the unit and its contents.
To minimize shock and fire hazards, be sure that the unit is properly
grounded. For your safety and protection, all units are equipped with a
special three-prong grounding plug on the service cord.
All units are designed for indoor use. Outdoor use may cause significant
damage to the unit.
PRECAUTIONS
To minimize shock and fire hazards, be sure not to overload the outlet.
To minimize electric shock and malfunction, do not spray the unit with
water.
To minimize fire hazards, do not use flammable spray products near the
unit.
After unplugging the unit, wait at least 6 minutes before re-plugging it. It
may cause compressor failure if plugged in before 6 minutes waiting
period.
Cautions for cleaning:
Unplug the power cord before cleaning.
Do not unplug/plug the power cord with wet hands.
Do not use an abrasive cleaners, solvents or polishing agents on plastic
parts. Doing so might cause cracking or discoloring.
When it is not in use
Unplug the power cord.
2
GLASS DOOR MERCHANDISERS
Wipe inside with dry cloth, and you may leave the door slightly open to
eliminate moisture and odor.
OPERATION/MAINTENANCE
When loading the unit:
Be careful not to block the air duct located at the back and the fan on the
ceiling of the unit with contents.
Blocking the air flow may cause decrease in performance.
For the best performance, maintain at least 4 inches of clearance between
the contents and the air duct.
Set the shelves that comes with the unit to fit your needs.
Temperature controller:
The controller is located at the right, front corner of the ceiling.
Temperature is set as “4” at default.
Do not leave the unit door open for long period of time. For the most
efficient operation, close the door immediately after the use.
TROUBLE SHOOTING GUIDE
SYMPTOMS REMEDY
COMPRESSORS WILL NOT
START
Check if the power cord has been
plugged in.
Check for blown fuse.
POOR PERFORMANCE
Move the unit from direct sun light, and
avoid installing heating devices near the
unit.
Install the unit in a well ventilated place
with minimum of 6” clearance in the
back.
Check the condenser, and clean if
heavy dust is collected.
3
GLASS DOOR MERCHANDISERS
Check to see if contents are blocking
the air duct.
Check the temperature controller for
possible incorrect temperature setting.
Check to see if refrigerant charge is low.
Make sure the door is completely
closed.
NOT INTERIOR LIGHT
Turn off the light switch and turn it on
again.
Make sure the bulb is correctly inserted
into the sockets.
Check the bulb, and replace it if blown.
UNIT NOISY
Make sure to install the unit on level
surface.
Make sure to maintain the minimum
clearance of 6” from the wall.
Check for the loose parts or mounting.
Make sure the tubing is free from any
contact to avoid tubing rattle.
CONDENSATION ON CABINET
AND/OR FLOOR
Reduce the relatively humidity in the
area where the unit is installed.
Gasket on door or head section is not
sealing properly. Repair or replace
gasket as necessary.
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Norpole NPGR2-B Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI