M•Flex12. M•Flex 12XP. M•Flex15. M•Flex15XP. M•FlexS. M•FlexSXP
M•Flex12. M•Flex 12XP. M•Flex15. M•Flex15XP. M•FlexS. M•FlexSXP
M•Flex12. M•Flex 12XP. M•Flex15. M•Flex15XP. M•FlexS. M•FlexSXP
M•Flex12. M•Flex 12XP. M•Flex15. M•Flex15XP. M•FlexS. M•FlexSXP
M•Flex12. M•Flex 12XP. M•Flex15. M•Flex15XP. M•FlexS. M•FlexSXP
M•FLEX
Installation guide
M•Flex S/XP PA speakers
2
3
Sub
Passive
How to connect audio cables and plugs
Rear panel interface for M•Flex S subwoofer
How to use M•Flex Sub with M•Flex 12/15 and a mixer
Rear panel interface for M•Flex 12XP/15XP and SXP
3
4
5
6
Content
Every effort has been taken to ensure that the content of these instructions are
correct. Mach Speakers A/S does not accept any liability for loss or damage
caused or alleged to be caused directly or indirectly by these instructions. The
contents of the instructions may be subject to change without notice. Mach
Speakers A/S makes no warranty of any kind with regards to these instructions.
2003 Mach Speakers A/S, Denmark.
All rights reserved. No part of these instructions may be reproduced, in any
form or by any means, without permission in writing from Mach Speakers A/S,
Denmark.
Mach Speakers A/S • Perspektivvej 2 • 9900 Fredrikshavn • Denmark
Tel: +45 72 15 08 52 • Fax: +45 98 43 14 15 • e−mail: [email protected]
Installation guide for M•Flex speakers
P/N 00000000A, Rev A
Cables/plugs
2
3
Cables/plugs
Red
1-
1
+
2+
2
-
IMPORTANT
Note
N
L
Yellow/Green
Blue
Black
1
2
3
G
Cold
Common
Hot
1
2
3
G
Cold
Common
Hot
HotCold
Common
Tip
Ring
HotCold
Common
Tip
Black
Plug wiews from wiring side
Plug wiews from wiring side
How to connect audio cables and plugs
On the following pages you will nd information about how to hook up your M-Flex speakers. To save time and a lot of
sweat and tears please follow these instructions carefully. Before you start make sure that all cables are without damages
and the plugs are clean and dry.
Make sure only to use good quality audio cables, plugs and connectors with the M-
Flex products. When connecting plugs to cables please follow this connection guide
carefully. If there is any doubt about how to connect a specic plug please contact the
supplier.
TS plug (mono)
Standard mono (unbalanced) phone plug, used in the
Line1, Line2, Mix.Out and most mixer connections.
TRS plug (stereo)
Standard stereo (balanced) phone plug, used in
Line1, Line2, Mix.Out and for balanced mixer
connections.
Balanced XLR plug (male)
Standard XLR plug for microphone connector, used
for Mic In.
Balanced XLR plug (female)
Standard XLR plug for microphone connector, used
for Mic Link.
Industrial Connectors / PowerCon®
Locking 3 pole equipment AC connector for 110/250 V
AC. High current capacity (up to 20 A).
Remember to bring the power cord at all times, as the professional PowerCon mains
connector is only available from specialized suppliers.
Installation guide for M•Flex speakers
Speakon®
4 pole cable connector with latch lock. Intermates
with 4-pole chassis connector and makes contact with
+1/-1.
4
5
Limiter on
Link
Power On
Signal In
Power Section
On-board DSP tecnology
CAUTION:
Rigging of
this system
should only
be done by
qualified
persons!
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
risk of fire or
0dB
-¥
0dB
-¥
Output
Input
In
High
pass
Off
On
High
gain
Low
gaín
In/link
In/link
High out High out
M·FLEXbyMach
A
MARTIN
Professional Product
Installation guide for M•Flex speakers
1
2
3
4
5
6
7
Rear panel interface for M•Flex S subwoofer
M-Flex Sub products feature build-in switch-mode amplication and analogue cross over. As such it represent the next
generation of composite moulded speaker design. The amplier interface is the connection panel which is mounted on the
backside of the speaker. The connection panel has several connectors and adjustments controls which will be described
on the following pages.
This section describes the rear panel inter-
face on the M-Flex S
1. Limiter on
Red LED indicates when the limiter is active.
2. High pass selector
On: High pass lter cuts the frequency on the output at
110 Hz.
Off: High pass lter cuts the frequency on the output at
35 Hz.
3. Power on
Blue LED indicates when AC power in on. The LED turns
off when the unit is in standby waiting for signal.
4. Low gain controler
Adjust the bass output of the speaker from (- ∞ , 0 dB).
5. Signal in
Green LED indicates that the unit is receiving signal.
6. In&link
This XLR/JACK enables you to link the Line input signal
to other M•Flex speakers. It is a passive through link so
the output of the signal of the plugs is similar to the input
signal.
7. Link
Main Power through connection link.
8. High gain
Adjust the signal output of the High out from (- ∞ , 0 dB).
9. Power switch
When turning on the M•Flex speaker, make sure that all
sources such as mixer, musical instruments or CD players
have been turned on, and the input gain controls have been
turned down.
10.High out
Balanced JACK plug output.
11. Power plug
The enclosed power cable feature a Neutric PowerCon
plug.
12. High out
Balanced XLR plug output.
8
9
10
11
12
Sub
If the High pass selector is in off mode the speaker connected to the output will receive a
full range signal. (the same signal as the sub and the same frequency).
Note
4
5
Power Section
Output Adjust
Limiter on
Treble
Bass
+6dB
+6dB
-14dB
-14dB
Master
volume
Power On
+5dB
+40dB
Mic.
gain
Signal In
Mic.
CAUTION
:
Rigging of
this system
should only
be done by
qualified
0dB
-¥
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
Mix
Out
Line 2
Line 1
Mic In
Mic Link
Power
Input Section
M·FLEXbyMach
On-board DSP tecnology
Limiter on
Link
Power On
Signal In
Power Section
M·FLEX
by
Mach
On-board DSP tecnology
CAUTION:
Rigging of
this system
should only
be done by
qualified
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
0dB
-¥
0dB
-¥
Output
Input
In
High
Off
High
Low
In/link
In/link
High out High out
Limiter on
Link
Power On
Signal In
Power Section
M·FLEX
by
Mach
On-board DSP tecnology
CAUTION:
Rigging of
this system
should only
be done by
qualified
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
0dB
-¥
0dB
-¥
Output
Input
In
High
Off
High
Low
In/link
In/link
High out High out
Limiter on
Link
Power On
Signal In
Power Section
M·FLEX
by
Mach
On-board DSP tecnology
CAUTION:
Rigging of
this system
should only
be done by
qualified
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
0dB
-¥
0dB
-¥
Output
Input
In
High
Off
High
Low
In/link
In/link
High out High out
Power Section
Output Adjust
Limiter on
Treble
Bass
+6dB
+6dB
-14dB
-14dB
Master
volume
Power On
+5dB
+40dB
Mic.
gain
Signal In
Mic.
CAUTION
:
Rigging of
this system
should only
be done by
qualified
0dB
-¥
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
Mix
Out
Line 2
Line 1
Mic In
Mic Link
Power
Input Section
M·FLEXbyMach
On-board DSP tecnology
Power Section
Output Adjust
Limiter on
Treble
Bass
+6dB
+6dB
-14dB
-14dB
Master
volume
Power On
+5dB
+40dB
Mic.
gain
Signal In
Mic.
CAUTION
:
Rigging of
this system
should only
be done by
qualified
0dB
-¥
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
Mix
Out
Line 2
Line 1
Mic In
Mic Link
Power
Input Section
M·FLEXbyMach
On-board DSP tecnology
Power Section
Output Adjust
Limiter on
Treble
Bass
+6dB
+6dB
-14dB
-14dB
Master
volume
Power On
+5dB
+40dB
Mic.
gain
Signal In
Mic.
CAUTION
:
Rigging of
this system
should only
be done by
qualified
0dB
-¥
CAUTION:
Do not open
this
producor
expose this
system to
rain or
moisture to
reduce the
Mix
Out
Line 2
Line 1
Mic In
Mic Link
Power
Input Section
M·FLEXbyMach
On-board DSP tecnology
Installation guide for M•Flex speakers
In/link
Stereo setup with two M•Flex S, two M•Flex 12/15 and a mixer
In/link
Line 1 Line 1
High out High out
Mixer
M•Flex 12/15 M•Flex 12/15
M•Flex S M•Flex S
Mono setup with one M•Flex S, two M•Flex 12/15 and a mixer
Mixer
M•Flex S
M•Flex 12/15 M•Flex 12/15
Sub
How to use M•Flex Sub with M•Flex 12/15 and a mixer
6
CAUTION:
Rigging of this system
should only be done by
qualified persons!
INPUT/
LINK
INPUT/
LINK
Default
connection
1+/1-
Default
connection
1+/1-
M·FLEXbyMach
A MARTIN ProfessionalProduct
CAUTION:
Rigging of this system
should only be done by
qualified persons!
INPUT/
LINK
INPUT/
LINK
Default
connection
1+/1-
Default
connection
1+/1-
M·FLEXbyMach
A MARTIN ProfessionalProduct
CAUTION:
Rigging of this system
should only be done by
qualified persons!
INPUT/
LINK
INPUT/
LINK
Default
connection
1+/1-
Default
connection
1+/1-
M·FLEXbyMach
A MARTIN ProfessionalProduct
CAUTION:
Rigging of this system
should only be done by
qualified persons!
INPUT/
LINK
INPUT/
LINK
Default
connection
1+/1-
Default
connection
1+/1-
M·FLEXbyMach
A MARTIN ProfessionalProduct
CAUTION:
Rigging of this system
should only be done by
qualified persons!
INPUT/
LINK
INPUT/
LINK
Default
connection
1+/1-
Default
connection
1+/1-
M·FLEXbyMach
A MARTIN ProfessionalProduct
Note
Installation guide for M•Flex speakers
Rear panel interface for M•Flex 12XP/15XP and SXP
Input/Link
Input/Link
Input/link
Stereo setup with two M•Flex SXP, two M•Flex 12XP/15XP and a mixer
Input/link
Input/Link Input/Link
Mixer
M•Flex 12XP/15XP M•Flex 12XP/15XP
M•Flex SXP M•Flex SXP
The M•Flex XP series consists of three models. M•Flex 12XP, M•Flex 15XP and the M•Flex SXP sub woofer. All models
feature a Speakon speaker terminal with link option. This option allows two or more speakers to be operated in parallel
from one amplier.
The impedance is 4 ohm when two M•Flex XP speakers are operated in parallel and
approximately 2,5 ohm when three are operated in parallel.
Input/link Input/link
Passive
Power amp
-
1
-
2
-
3
-
4
-
5
-
6
Mach M Flex XP Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Tangent AMP200ZIL Datasheet
-
AUSTRALIAN MONITOR PICO-RMK Installation guide
-
ATEN SXP320A User manual
-
AUSTRALIAN MONITOR FLEX30 Operating instructions
-
Peecker Sound HT800 High Tecnologies Series User manual
-
ITW Buildex 8295922 Installation guide
-
Martin ViroSphere Outdoor User manual
-
Ascon tecnologic TRH42 Operating instructions
-
-
