American Standard T420.432.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
DIVERTER TRIM KIT
Installation
Instructions
M965032 REV.1.5 (4/15)
T42043X
Series
PORTSMOUTH
®
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth
(as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
ALL CONNECTIONS 1/2" NPT
LEVER
HANDLE
CROSS
HANDLE
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8")
66mm MAX.
(2-5/8")
71mm
(2-3/4")
57mm HOLE SIZE
(2-1/4")
70mm
(2-5/8")
51mm
(2")
42mm
(1-11/16")
M965032 REV.1.5 (4/15)
OPERATING THE VALVE
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
3
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
2
HANDLE INSTALLATION
2
1
3
4
5
6
Rotate the slot on KNOB MOUNT (1) about 15˚ to the left and install
onto VALVE STEM (2). Make sure to push KNOB MOUNT (1) until it
is properly installed against valve.
Thread HANDLE SCREW (3) into VALVE STEM (2) and tighten.
Align the two Ribs inside the HANDLE (4) with the slot on the
KNOB MOUNT (1). Push HANDLE (4) onto KNOB MOUNT (1).
Tighten SET SCREW (5) in handle with
HEX WRENCH (6) supplied.
15˚
15˚
RIBS
VIEW “A”
SLOT
SLOT
HANDLE (4)
HANDLE RIBS
VIEW “A”
KNOB MOUNT (1)
M965032 REV.1.5 (4/15)
PORTSMOUTH
®
DIVERTER TRIM KIT
MODEL NUMBERS
012288-YYY0A
ESCUTCHEON KIT
954027-YYYOA
ESCUTCHEON HOLDER
A923348-0070A
HANDLE ADAPTER
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2010
HOT LINE FOR HELP
M918318-0070A
HANDLE SCREW
T42043X Series
M950276-YYY0A
LEVER HANDLE KIT
M950275-YYY0A
CROSS HANDLE KIT
M923045-0070A
HEX WRENCH
M923045-0070A
HEX WRENCH
CHROME
BLACKENED BRONZE
OIL RUBBED BRONZE
SATIN NICKEL
002
068
224
295
Replace the "YYY" with
appropriate finish code
-
1
-
2
-
3
American Standard T420.432.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard T555.430.224 Installation guide
-
-
-
-
American Standard T005.430.224 Installation guide
-
-
-
American Standard 7001.000 User manual
-
-