2. Toro
  3. Rear Pivot Arm Kit, Heavy-Duty Recycler/Rear Bagger Lawn Mower

Toro Rear Pivot Arm Kit, Heavy-Duty Recycler/Rear Bagger Lawn Mower Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Rear Pivot Arm Kit, Heavy-Duty Recycler/Rear Bagger Lawn Mower Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3394-373RevA
RearPivotArmKit
Heavy-DutyRecycler
®
/RearBaggerLawnMower
ModelNo.131-5305
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Important:Savethepartsthatyouremovefromthe
machineexceptthosethatyouareinstructedtodiscard.
1.Removetheangenutandthewheelfromthemachine
(Figure1).
Figure1
1.Wheel2.Flangenut
2.Removetheretainingringsandthepiniongearfrom
themachine(Figure2).
Figure2
1.Bolts(1/4x3/4inch)
3.Retainingrings
2.Piniongear
3.Removethe3bolts(1/4x3/4inch)thatsecurethe
height-of-cutassemblytothemachine(Figure2).
4.Removetheheight-of-cutassemblyfromthemachine.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3394-373*A
5.Removetheretainercover,retainingring,andwasher
fromtheheight-of-cutplate(Figure3).
Figure3
1.Retainercover
4.Endofretainer
2.Retainingring
5.Height-of-cutplate
3.Washer
6.Disassembletheremainingpartsoftheassembly
(Figure4).
Note:Discardtheheight-of-cutplate,rearpivotplate,
bolt(5/16x3/4inch),andBellevillewasher.
Figure4
1.Height-of-cutplate
(discard)
5.Springarm
2.Bolt(3/8x2-3/4inches)
6.Retainer
3.Bellevillewasher(discard)7.Bolt—5/16x3/4inch
(discard)
4.Rearpivotarm(discard)
7.Assemblethepartsfortheheight-of-cutassembly
(Figure5)usingtheheight-of-cutplate,therearpivot
plate,andthebolt(5/16x3/4inch)fromthekit.
Note:Torquethebolt(5/16x3/4inch)to20to23
N-m(180to200in-lb).
Figure5
1.Height-of-cutplate(from
thekit)
4.Springarm
2.Bolt(3/8x2-3/4inches)
5.Retainer
3.Rearpivotarm(fromthe
kit)
6.Bolt—5/16x3/4inch(from
thekit)
8.Installthewasher,retainingring,andretainercoveron
theheight-of-cutplate(Figure3).
9.Installtheheight-of-cutassemblyontothemachine
withthe3bolts(1/4x3/4inch)asshowninFigure6.
Note:Torquetheboltsto11to14N-m(100to120
in-lb).
Figure6
10.Installthepiniongearwiththeretainingrings(Figure
2).
11.Securethewheeltothemachinewiththeangenut
(Figure1).
Note:Torquetheangenutto28to45N-m(250
to400in-lb).
12.Repeatthisprocedurefortheotherrearwheel
assembly.
2
/