Minka Lavery 3081-613-L Operating instructions

Brand: Minka Lavery

Model: 3081-613-L

Type: Operating instructions

This manual is also suitable for

3081-281-L

Minka Lavery 3081-613-L is a lighting fixture designed for indoor use. It can be mounted on a ceiling to provide ambient lighting for a room. The fixture has a circular metal base that attaches to the ceiling, and a glass shade that encloses the light bulb. The fixture can be used with a variety of light bulbs, including incandescent, fluorescent, and LED bulbs. The fixture is easy to install and can be completed in a few simple steps. It is also easy to maintain, as the glass shade can be easily removed for cleaning.

Minka Lavery 3081-613-L is a lighting fixture designed for indoor use. It can be mounted on a ceiling to provide ambient lighting for a room. The fixture has a circular metal base that attaches to the ceiling, and a glass shade that encloses the light bulb. The fixture can be used with a variety of light bulbs, including incandescent, fluorescent, and LED bulbs. The fixture is easy to install and can be completed in a few simple steps. It is also easy to maintain, as the glass shade can be easily removed for cleaning.

INSTALLATION INSTRUCTIONS

Item#3081-613-L (New. 2017/04/11)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker. If

necessary, remove old fixture including the mounting

hardware.

2. Carefully unpack your new fixture and lay out all the

parts on a clear area. Take care not to lose any small

parts necessary for installation.

3. Attach the circular strap (A) to the outlet box with the

two mounting screws (B) (Size: #8-32N*L0.5”). The

side of the circular strap marked “GND” must face

out.

4. Thread the studs (C) into the pre-drilled holes of the

circular strap (A) spaced the same distance apart as

the holes in the back plate of the fixture body (D).

CONNECTING THE WIRES (Fig. 2)

5. At this point, connect the electrical wires as shown in

Fig. 2, making sure that all wire connectors are

secured. If your outlet box has a ground wire (green

or bare copper), connect the fixture’s ground wire to

it. Otherwise, connect the fixture’s ground wire

directly to the circular strap using the green screw

provided. After wires are connected, tuck them

carefully inside the outlet box.

COMPLETING THE INSTALLATION (Fig. 1)

6. Place fixture body (D) onto studs (C) and secure with

cap nuts (E).

7. Place the glass shade (F), metal ring (G) over the

socket, and fasten with socket ring (H).

Your installation is now complete. Return power to

the outlet box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

LA-2755E

FIXTURE

WIRES

Black or

Smooth

H

O

U

S

E

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

H

O

U

S

E

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

H

O

U

S

E

WIRES

Green

(Ground)

Set# A-020

- Circular strap

- Ground screw

- Mounting Screw*2

Socket ring # SKT-RING-26

A

B

D

C

E

F

H

G

1

Minka Lavery 3081-613-L Operating instructions

Brand: Minka Lavery

Model: 3081-613-L

Type: Operating instructions

This manual is also suitable for

3081-281-L

Minka Lavery 3081-613-L is a lighting fixture designed for indoor use. It can be mounted on a ceiling to provide ambient lighting for a room. The fixture has a circular metal base that attaches to the ceiling, and a glass shade that encloses the light bulb. The fixture can be used with a variety of light bulbs, including incandescent, fluorescent, and LED bulbs. The fixture is easy to install and can be completed in a few simple steps. It is also easy to maintain, as the glass shade can be easily removed for cleaning.

Download PDF

Related papers

Other documents