Thank you for choosing our product! We strive to provide the best quality and
services for our customers. Would you kindly share your experience on Amazon if
you are satisfied? Should you have any issues, please don't hesitate to contact us.
Telephone：800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
PSSS3
V1.0
SPEAKER FLOOR STAND
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM
IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE
BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact us at
[email protected] or a qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and
hardware included will be used. If you require replacement parts, please contact us at
This product may contain moving parts. Use with caution.
Please check www.perlesmith.com for more products and company information.
WARNING！
Screwdriver
TOOLS NEEDED (NOT INCLUDED)
x 2
x 2
x 2
01
03
04
Base
Post assembly
x 2
02
Post extension
Small Plate
x 2
05
Medium Plate
x 2 x 2
06
Large Plate
07
Vertical Plate
x 2
08
Velcro A and B
SUPPLIED PARTS
φ6.5
Washer
A
B
C
E
F
D
HARDWARE KIT
M6x12mm
Screw
Screw
1/4’’ x1/2’’
Plastic Nut
M6
Nut
Screw
M5x15mm
x2 x2 x2 x2x2x2
1
STEP 1
Attach the Nails or Rubber Pads to the Base
Rotate and insert the rubber pads into the holes.
I
J
K
Used for carpet
Used for marble floors or wooden floors
Washer
#6
M4x16mm
Wood Screw
φ4.7
Washer
x2 x6 x6 x6
G H J KI M N
L
Nail Nut Pad
#6-32x1-1/4
Screw
#6
Nut
x2
x2
x2 x2
2
STEP 2A
Fasten the Post Extension to the Post Assembly
03
03
02
02
STEP 2B
Fasten the Post assembly to the base
01
02
03
3
Secure Speaker to Stand
STEP 2C
STEP 3
Adjust the Post Assembly to the Desired Height
Speaker option A1: Keyhole insert
1.Attach Vertical Plate [07] with the Screw M5x15 [A]
2. Thread plastic nut [C] to screw
1/4’’ x1/2’’ [B]
3. Insert screw [B] into the keyhole of the speaker
and fasten the plastic nut [C]
OPT
A1
A
02
C
B
Lift
Tighten
Loosen
4
Speaker Option A2: Keyhole Insert
Speaker Option A3: Wooden Shell
Speaker without Thread hole
OPT
A3
H
G
OPT
A2
Center line
D,L
E,M
F,N
5
Speaker Option B2: Speakers with Smooth Surface on the Bottom without Thread Holes
Speaker Option B1: Thread Holes Locate at the Bottom of the Speaker
Separate velcro
A and B [08],
remove the
paper.
Stick the vercro A and B [08] on
the square plate [04] or [05] or
[06] and the bottom of the
speaker.
Cut the over length
velcro if necessary.
Attach the speaker
to the plate [04] or
[05] or [06] .
OPT
B2
A
02
02
Special screws
(Not included in
the hardware kit)
04 05 06
OPT
B1
or or
6
08
08
08
08
STEP 4
Route the cables
Cable comes out from the base 01
7
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
PERLESMITH PSMTK3 Installation guide
-
-
-
PERLESMITH PSMFK1 Installation guide
-
-
-
-
-
-