Copystar KM-C2520 Installation guide

Type
Installation guide
KYOCERA Net Admin 1
Legal Notes
Unauthorized reproduction of all or part of this guide is prohibited.
The information in this guide is subject to change without notice.
We cannot be held liable for any problems arising from the use of this product, regardless of the information
herein.
© 2019 KYOCERA Document Solutions Inc.
Regarding Trademarks
KYOCERA Net Admin is a trademark of KYOCERA Document Solutions Inc.
Microsoft®, Windows®, and Internet Explorer are registered trademarks of Microsoft Corporation in the U.S.
and/or other countries.
All other brand and product names herein are registered trademarks or trademarks of their respective
companies.
Examples of the operations given in the “Microsoft SQL Server Setup” section in this guide support the Microsoft
SQL Server 2008 R2.
The features described in this guide vary depending on your device model.
KYOCERA Net Admin 2
Table of Contents
Introduction ................................................................................................................... 3
Change History ...................................................................................................................... 3
Approved Updates ........................................................................................................ 4
Installation .............................................................................................................................. 5
KYOCERA Net Admin 3
Introduction
This supplement to the KYOCERA Net Admin Installation Guide provides
information specific to the improvements and new features added to KYOCERA Net
Admin, starting with software version 3.4.
This document is intended to complement, not replace, the existing guide. For
general installation instructions not covered in this supplement, see the KYOCERA
Net Admin Installation Guide.
Change History
KYOCERA Net Admin version 3.8
Updated Legal Notes and Regarding Trademarks section
Added support for Windows Server 2019
Removed support for usage data collection
KYOCERA Net Admin version 3.7
No update to this supplement
KYOCERA Net Admin version 3.6
Removed support for Windows 8
KYOCERA Net Admin version 3.5
Added support for usage data collection
Updated the supported .NET Framework version from 4.0 to 4.5
KYOCERA Net Admin version 3.4
Updated steps for installing KYOCERA Net Admin to include Java installation
Added steps for resolving security certificate error when opening the application
Updated the supported Java Runtime Environment version from 7 to 8
Updated the list of supported Windows operating systems:
Added support for Windows Server 2016
Removed support for Windows Vista, Windows Server 2003, and
Windows XP
Updated the supported version of Internet Explorer web browser
KYOCERA Net Admin 4
Approved Updates
This section contains only the updated information based on the changes included in
KYOCERA Net Admin version 3.4 and later. For general instructions not covered in
this section, see the KYOCERA Net Admin Installation Guide.
KYOCERA Net Admin 5
Installation
The KYOCERA Net Admin installation consists of two main software components or
consoles: Administration and Device Manager. The KYOCERA Net Admin Agent
and Multi-Set Template Editor are included in the installation, and are also available
as separate installers along with the Local Device Agent (LDA). The KYOCERA Net
Admin Agent and Multi-Set Template Editor can be installed locally or remotely at
multiple sites.
The Administration console lets you manage user accounts and roles, user
subscriptions, network discovery, and system settings. The Device Manager console
lets you manage device data, reports, polling, alerts, and preferences.
The KYOCERA Net Admin Agent is a service that communicates network device
information to KYOCERA Net Admin. The LDA is a service that communicates
information about USB-connected Kyocera devices on a network. The Multi-Set
Template Editor lets you create or change settings templates.
The KYOCERA Net Admin installation provides the third party software Java
Runtime Environment 8 and, if selected, PostgreSQL. If selected, Microsoft SQL
Server must be installed separately. Your server must have Microsoft .NET
Framework 4.5 or later to install KYOCERA NetAdmin, Agent, LDA, and Multi-Set
Template Editor.
System Requirements
Supported Operating Systems
KYOCERA Net Admin is compatible with the following Microsoft Windows operating
systems:
Windows 10
Windows 8.1
Windows 7
Windows Server 2019
Windows Server 2016
Windows Server 2012 R2
Windows Server 2012
Windows Server 2008 R2
Windows Server 2008
Supported Browsers
Microsoft Internet Explorer 11. Cookies must be enabled.
Server Installation
The KYOCERA Net Admin server installer provides an easy and intuitive process for
installing and configuring KYOCERA Net Admin. The wizard gathers the
administrator’s selections and system information to prepare the installation.
KYOCERA Net Admin 6
To ensure secure communication, the time setting must be no more than 1 minute
apart on server and agent computers. For computers in different time zones, use a
global time server or domain time server to ensure synchronized time settings.
Installing KYOCERA Net Admin
Note: Make sure your firewall is configured correctly to allow communication
between KYOCERA Net Admin components (TCP port: 8731). KYOCERA Net
Admin cannot be installed on a server used as a domain controller.
Note: If you plan on using the Microsoft SQL database, you must install and
configure it before installing KYOCERA Net Admin. Only one instance of the
KYOCERA Net Admin database can be supported on the Microsoft SQL server.
1 Copy and extract the KYOCERA Net Admin (KNA) zip file to your preferred
server, and then click KmInstall.exe to start the installation wizard.
2 In the license agreement screen, click View License Agreement to read, view,
and print a copy of the license agreement. To proceed with the setup installation,
click Accept.
3 In the Manage Products page, click Install. You can also open and view the user
and installation guides and the Readme from the Documentation icon.
4 In the Products to install page, click Next to accept the default settings. Note that
clicking Install now begins the installation automatically.
5 In the Destination for all software page, click Next to accept the default folder, or
click Browse to locate another folder of your choice. Click Next.
6 In the Ports page, accept the defaults or type custom port numbers. Available
port numbers range from 1 to 65535. Click Next.
7 In the Network Setup page, select Local network (default), or Remote
network.
8 In the Database Setup page, select PostgreSQL or Microsoft SQL.
9 Configure the selected database:
For PostgreSQL, if this is the first time you are installing the application, the
Password page appears. Type a valid password, and then click Next.
For Microsoft SQL, provide the following information:
The User ID and Password you set up during the Microsoft SQL installation.
The Host name of the computer the Microsoft SQL database is installed on.
The Instance name entered during the database setup.
The Port number you set up in SQL Server Configuration Manager. The
default is 1433.
KYOCERA Net Admin 7
10 Do either of the following:
To make any setup changes, click Back.
To proceed, click Install now.
11 If the Java package is not yet installed, the Java setup dialog box appears. Select
from the following options:
To save the file to another location, click Change destination folder.
To cancel the installation, click Cancel.
KNA requires Java package to complete the installation. If you select cancel,
the wizard stops the progress of the installation.
To accept the license terms and continue with the installation, click Install.
12 If there are older versions of Java installed, the uninstall dialog box appears. Do
either of the following:
To uninstall at a later time, click Remind Me Later.
To proceed, click Uninstall.
In the Java setup complete dialog box, click Next > Close.
The KNA installation resumes after the Java package is installed.
13 When the process is completed, the Finished page appears. The Start now check
box is selected by default. Click Close to open the application.
Remote Agent Installation
This section is required for administrators who install KYOCERA Net Admin Agent
on a remote network.
The KYOCERA Net Admin Agent is a service that communicates network device
information to KYOCERA Net Admin. Agents can be installed on the KYOCERA Net
Admin server and on remote computers.
To ensure secure communication, the time setting must be no more than 1 minute
apart on server and agent computers. For computers in different time zones, use a
global time server or domain time server to ensure synchronized time settings.
You can choose to install KYOCERA Net Admin Agent on a remote computer either
by RPC connections or by a Stand-alone installer.
RPC Connections for Remote Agent Installation
The administrator can set policies that are applied to the computer for any user
who logs on to the KYOCERA Net Admin server.
For agent installation on a remote computer, the Remote Procedure Call (RPC)
endpoint for the spooler must be set up to allow agent connections. The Allow Print
Spooler to accept client connections policy manages access to the Print Spooler.
For information about group policy settings, refer to Microsoft documentation.
KYOCERA Net Admin 8
Allowing the Remote Agent to Access Client Connections
1 In Local Group Policy Editor, click Computer Configuration > Administrative
Templates > Printers.
2 From the Setting list, double-click the Allow Print Spooler to accept client
connections policy.
3 Select Enabled so the Print Spooler will always accept client connections.
4 Click OK.
5 Restart the Print Spooler service for changes to this policy to take effect. For
information about restarting the Print Spooler, refer to Microsoft documentation.
Clearing the File Sharing Option in a Remote Workgroup Computer
Before installing a remote agent, the file sharing option should be turned off in the
remote workgroup computer.
1 In Control Panel, click Folder Options.
2 In the Folder Options dialog box, click View.
3 In the Advanced Settings list, clear the Use Sharing Wizard (Recommended)
check box.
Adding a Remote Network and Remote Agent
1 Open KYOCERA Net Admin in your Internet browser.
2 In the Administration console, click Preferences > Networks and agents > Add
Network, and proceed through the wizard to the Enter the Agent Details page.
3 Type the Agent Name and Agent IP Address.
4 Type the Agent Timeout, or accept the default.
5 Under Administrator login information for the remote host (available if you
selected New Agent in the previous page), type the Agent Login, Agent
Password, and Agent Domain of the administrator.
6 Click Next to continue and finish the Add Network wizard.
USB Device Connections
KYOCERA Net Admin can discover and manage local USB devices (connected to
computers in the network) through the Local Device Agent (LDA). It displays them in
the device list the same way as network-connected devices. The LDA can support
KYOCERA Net Admin 9
several USB connected devices at the same time, but KYOCERA Net Admin shows
only one of them.
Install the USB device to the computer first, then the LDA.
Requirements
The following requirements are needed for the USB connection and LDA to function
correctly:
KYOCERA Net Admin must be installed and operating on the server.
Microsoft .NET Framework 4.5 or later must be installed on the computer.
The computer must have at least one connected local Kyocera USB device.
The computer must have a real network interface card.
The computer must be connected to the network.
The computer must have an IP address in the connected network.
TCP port numbers 9000 and 9072 on the computer must be free and not
blocked by a firewall.
The user installing the LDA must have administrator rights to install a Microsoft
Windows service.
KYOCERA Net Admin Login
At the end of the installation wizard, you can leave the Start now check box selected
to open the application after clicking Close. Once the application is opened, you can
use the browser to bookmark the KYOCERA Net Admin web address.
On the login page, you can use the same word for the User name and Password:
An administrator uses admin
A read-only user uses guest
For greater security, we recommend changing the default passwords immediately
after the first login.
You will be automatically logged off after the time of inactivity set by the
administrator. The default time is 30 minutes.
Note: To prevent the browser from freezing, do not use the keyboard shortcut
Ctrl+N to open a new window while the application is running.
Starting and Logging In
You can start KYOCERA Net Admin using Internet Explorer 11.
1 In the browser, type the application’s address in the format: https://<computer
name or IP address>:<port number>/netadmin/ or find the URL in the Favorites or
browser history.
2 On the login page, type the User name and Password.
3 Choose a console to open from the list, or choose Default Console. You can
change the default console after logging in.
KYOCERA Net Admin 10
4 Click Log in.
Security Certificates
When using Windows Internet Explorer to access a secure HTTPS connection, a
certificate error appears. This error indicates that the root certificate used for secure
communication is not trusted. You may continue to access the secure website or
resolve the certificate error to avoid getting the same error when reconnecting to the
application.
Resolving Security Certificate Error
1 In Windows Internet Explorer, click Continue to this website (not
recommended).
2 In the Address bar, click Certificate error > View certificates.
3 In the Certificate dialog box > General tab, click Install Certificate.
4 In the Certificate Import Wizard dialog box, click Next.
5 In the Certificate Store page, select Place all certificates in the following store,
and then click Browse.
6 In the Select Certificate Store dialog box, select Trusted Root Certification
Authorities, and then click OK.
7 Click Next > Finish.
8 In the Security Warning dialog box, click Yes.
9 In the Certificate Import Wizard dialog box, click OK.
To make sure that changes are applied, open the KNA application in a new
window and reenter your login information.
KNAIGSKDEN38V1.2019.03
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Copystar KM-C2520 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI