Front Bumper Replacement Instructions
Nota™ Chair
©Wenger Corporation 2006 Printed in USA 11/06 Part #190A170-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 733-0393 • International (call collect): (507) 455-4100 • www.wengercorp.com
Note: Please read and understand the Nota Chair™ Front Bumper Replacement Instructions before
attempting installation, assembly, or use.
Note: Remove all items from the shipping containers and sort the components by type, size, etc.
Refer to the illustrations on the following pages. If you need additional information, contact the
Wenger Corporation using the information listed below.
Nota Chair
CONTENTS
Saftey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Fastener Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Front Bumper Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front Bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2
S
AFETY
Read and understand the following safety instructions before installing the Front Bumper.
The Wenger Nota Chair is guaranteed free of defects in materials and workmanship for five full years.
Our guarantee assures you of either a full refund or repair or replacement of the defective materials or
workmanship without charge, at the discretion of our Customer Service Department. Just call a
Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a
product return is necessary, your representative will issue a return authorization. This is your sole
remedy for breach of this warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the
product is past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the
warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,
consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the
amount you paid for the product involved. Wenger reserves the right to make product changes without
obligation to incorporate such changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
WARRANTY
Always wear safety glasses
when operating the Electric
Drill or Rivet Gun.
Make sure that anyone who
helps install the Front
Bumper has read and
understands this manual.
!
CA UTION
!
CA UTION
REQUIRED TOOLS
The following tools must be supplied by the installer to replace the Front Bumper:
• Electric Drill with
1
/
8
” Drill Bit (to remove old rivets)
• Rivet Gun (to install using rivets)
• Electric Screwdriver or Drill with Phillips Head Bit (to install using screws).
FASTENER PARTS LIST
Screw, Self Tapping,
8-18 x
1
/
2
”, Phillips Head
1
/
8
” (0.125 mm) Diameter Rivet,
Blind, Grip 0.188/0.25”
3
F
RONT BUMPER REPLACEMENT
1. If the old Front Bumper and Rivets need to be removed,
Drill out the old Rivets or rivet remnants with an
Electric Drill fitted with an
1
/
8
” Drill Bit.
2. Place the Front Bumper over the front two center
holes in the frame on the bottom of the chair.
3. Secure the Front Bumper to the frame using either
two Rivets or two Screws.
Front
Bumper
Rivet or Screw
Location
R
EPLACEMENT PARTS LIST
FRONT BUMPER
Item Qty Description
1 1 Front Bumper
2 3*
1
/
8
” (0.125 mm) Diameter Rivet, Blind, Grip 0.188/0.25
3 3*
Screw, Self Tapping, 8-18 x
1
/
2
” Phillips Head
*Only two Rivets or Screws needed. There is a spare of each included.
3
4
2
1
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Freecom 56207 User manual
-
Wenger/SwissGear GA-7441-13F00 Datasheet
-
Wenger/SwissGear GA-7303-13F00 User manual
-
Lenovo 2518C3U Quick start guide
-
Lenovo NUM93MH User manual
-
Lenovo EDGE 13 User manual
-
-
-
Lenovo 43192QU Quick start guide
-
