CM Truck Beds SS Bed Owner's manual

Brand: CM Truck Beds

Model: SS Bed

Type: Owner's manual

This manual is also suitable for

CM Truck Beds Owner’s Manual

Table of Contents

Welcome 4

SS Truck Bed

Bed Installation 6

Wiring 7

Fuel Filler Assembly Installation 9

RD Truck Bed

Bed Installation 10

Wiring 11

Fuel Filler Assembly Installation 13

SK Truck Bed

Bed Installation 14

Wiring 15

Fuel Filler Assembly Installation 17

ER Truck Bed

Bed Installation 18

Wiring 19

Fuel Filler Assembly Installation 21

TM Truck Bed

Bed Installation 22

Wiring 23

Fuel Filler Assembly Installation 25

WD Truck Bed

Bed Installation 26

Wiring 27

Fuel Filler Assembly Installation 29

GP Truck Bed

Bed Installation 30

Wiring 31

Fuel Filler Assembly Installation 33

PL Truck Bed

Bed Installation 34

Wiring 35

Fuel Filler Assembly Installation 37

RD-AL Truck Bed

Bed Installation 38

Wiring 39

Fuel Filler Assembly Installation 41

Technical Information 42

CM.02.15.06

WELCOME TO THE CM TRUCK BEDS TEAM

Thank you for purchasing your new CM truck bed. You have

now joined an ever-growing team of quality conscious truck

equipment buyers.

CM Truck Beds is a wholly owned subsidiary of Contract

Manufacturer, L.L.C. manufacturing under the name of “CM

Truck Beds.” Our beds are designed and manufactured to

give you many years of reliable service. The combination of

quality materials and top craftsmanship continues to put CM

Truck Beds above the rest.

The safety and comfort of your cargo is the highest priority in

every CM design and manufacturing phase. However, as a

responsible truck bed owner, it is your responsibility to be

familiar with your new truck bed and to follow safety

guidelines and the recommended maintenance instructions to

ensure you have many years of safe hauling.

As you begin to use your new CM truck bed, this Owner’s

Manual will allow you to become more familiar with the

operation, maintenance, and care of your truck bed. This

manual will reference excerpts from other manufacturer’s

manuals which have components on CM Truck Beds products.

Disclaimer

All truck beds manufactured by CM Truck Beds are designed

to be used within the specific engineering guidelines. It is

suggested that all truck beds are to be used as designated by

the manufacturer.

CM Truck Beds reserves the right to make any change in

paint, design or construction as necessary for engineering. All

visual representation, specification and guidelines are based

on the latest product information available at the time of this

publication. All truck beds manufactured by Contract

Manufacturer, L.L.C., d.b.a. “CM Truck Beds” are covered in

this publication, with minor exceptions. For more information,

call us at 580-795-9999 or, you can write us at 1102 North

Industrial Road, Madill, OK 73446, e-mail:

customerser[email protected]m, web site:

www.cmtruckbeds.com.

SS Bed

BED INSTALLATION

Schematic

Explanation

Measure frame on truck and runners on bed to make sure you

have the right bed for the application. Then, using a spacer

between the runners and the frame, position the bed so that

the headache rack does not stick up over the cab of the truck

more than 1 ½”. There should be 2” of space between the cab

and the headache rack on the bed.

Attach fastener on each side of the front, middle, and rear;

bolt to the frame, and then either bolt the fastener to your

bed runners or weld them up solid. *

* NOTE: Attachment components are not supplied. Please use

adequate material to fasten the frame and bed together. For any

questions concerning materials, please contact the manufacturer.

* CAUTION: Observe safety precautions when using a welder on

your vehicle. These are only recommendations and installation design

is the responsibility of the installer. Follow vehicle manufacturer

specifications when attaching plates to the truck frame.

WIRING DIAGRAM: FORD, 2000 OR OLDER

CHEVY, 2002 OR OLDER DODGE

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using combined brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

WIRING DIAGRAM: 2003 DODGE TO PRESENT

AND 2001 CHEVY TO PRESENT

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using separate brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

* NOTE: Wires that are not used from harness need to have a scotch

lock put on the end so they don’t short out against the steel of the

truck bed.

FUEL FILLER ASSEMBLY INSTALLATION

* WARNING: Installation requires cutting and grinding. Keep all

ignition sources away when working with fuel tank filler pipe, or

serious injury or death can occur.

* CAUTION: Fuel tank filler pipe must be installed according to

vehicle requirements. Please read Owner’s Manual. Follow fuel tank

pipe manufacturer’s instruction or serious injury can occur.

The fuel filler door has been pre-determined to best suit the

tank location on your vehicle.

Fuel filler door has been tacked shut and welds will either

need to be cut or grinded off. After grinding welds, you should

be able to open spring loaded filler door.

Filler tube (not supplied by CM Truck Beds) should be routed

to fuel tank of your vehicle, per instructions supplied with

filler tube.

RD Bed

BED INSTALLATION

Schematic

Explanation

Measure frame on truck and runners on bed to make sure you

have the right bed for the application. Then, using a spacer

between the runners and the frame, position the bed so that

the headache rack does not stick up over the cab of the truck

more than 1 ½”. There should be 2” of space between the cab

and the headache rack on the bed.

Attach fastener on each side of the front, middle, and rear;

bolt to the frame, and then either bolt the fastener to your

bed runners or weld them up solid. *

* NOTE: Attachment components are not supplied. Please use

adequate material to fasten the frame and bed together. For any

questions concerning materials, please contact the manufacturer.

* CAUTION: Observe safety precautions when using a welder on

your vehicle. These are only recommendations and installation design

is the responsibility of the installer. Follow vehicle manufacturer

specifications when attaching plates to the truck frame.

WIRING DIAGRAM: FORD, 2000 OR OLDER

CHEVY, 2002 OR OLDER DODGE

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using combined brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

WIRING DIAGRAM: 2003 DODGE TO PRESENT

AND 2001 CHEVY TO PRESENT

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using separate brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

* NOTE: Wires that are not used from harness need to have a scotch

lock put on the end so they don’t short out against the steel of the

truck bed.

FUEL FILLER ASSEMBLY INSTALLATION

*WARNING: Installation requires cutting and grinding. Keep all

ignition sources away when working with fuel tank filler pipe, or

serious injury or death can occur.

*CAUTION: Fuel tank filler pipe must be installed according to

vehicle requirements. Please read Owner’s Manual. Follow fuel tank

pipe manufacturer’s instruction or serious injury can occur.

The fuel filler door has been pre-determined to best suit the

tank location on your vehicle.

There is a knock out plug where your fuel fill nozzle is to be

located. It is tack welded in place. To remove it, use a

hammer and punch and knock it out of the bed.

Filler tube (not supplied by CM Truck Beds) should be routed

to fuel tank of your vehicle, per instructions supplied with

filler tube.

SK Bed

BED INSTALLATION

Schematic

Explanation

Measure frame on truck and runners on bed to make sure you

have the right bed for the application. Then, using a spacer

between the runners and the frame, position the bed so that

the headache rack does not stick up over the cab of the truck

more than 1 ½”. There should be 2” of space between the cab

and the headache rack on the bed.

Attach fastener on each side of the front, middle, and rear;

bolt to the frame, and then either bolt the fastener to your

bed runners or weld them up solid. *

* NOTE: Attachment components are not supplied. Please use

adequate material to fasten the frame and bed together. For any

questions concerning materials, please contact the manufacturer.

* CAUTION: Observe safety precautions when using a welder on

your vehicle. These are only recommendations and installation design

is the responsibility of the installer. Follow vehicle manufacturer

specifications when attaching plates to the truck frame.

WIRING DIAGRAM: FORD, 2000 OR OLDER

CHEVY, 2002 OR OLDER DODGE

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using combined brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

WIRING DIAGRAM: 2003 DODGE TO PRESENT

AND 2001 CHEVY TO PRESENT

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using separate brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

* NOTE: Wires that are not used from harness need to have a scotch

lock put on the end so they don’t short out against the steel of the

truck bed.

FUEL FILLER ASSEMBLY INSTALLATION

*WARNING: Installation requires cutting and grinding. Keep all

ignition sources away when working with fuel tank filler pipe, or

serious injury or death can occur.

*CAUTION: Fuel tank filler pipe must be installed according to

vehicle requirements. Please read Owner’s Manual. Follow fuel tank

pipe manufacturer’s instruction or serious injury can occur.

The fuel filler door has been pre-determined to best suit the

tank location on your vehicle.

There is a knock out plug where your fuel fill nozzle is to be

located. It is tack welded in place. To remove it, use a

hammer and punch and knock it out of the bed.

Filler tube (not supplied by CM Truck Beds) should be routed

to fuel tank of your vehicle, per instructions supplied with

filler tube.

ER Bed

BED INSTALLATION

Schematic

Explanation

Measure frame on truck and runners on bed to make sure you

have the right bed for the application. Then, using a spacer

between the runners and the frame, position the bed so that

the headache rack does not stick up over the cab of the truck

more than 1 ½”. There should be 2” of space between the cab

and the headache rack on the bed.

Attach fastener on each side of the front, middle, and rear;

bolt to the frame, and then either bolt the fastener to your

bed runners or weld them up solid. *

* NOTE: Attachment components are not supplied. Please use

adequate material to fasten the frame and bed together. For any

questions concerning materials, please contact the manufacturer.

* CAUTION: Observe safety precautions when using a welder on

your vehicle. These are only recommendations and installation design

is the responsibility of the installer. Follow vehicle manufacturer

specifications when attaching plates to the truck frame.

WIRING DIAGRAM: FORD, 2000 OR OLDER

CHEVY, 2002 OR OLDER DODGE

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using combined brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

connection is a 6 wire pig tail to tie directly into the truck

functions.

WIRING DIAGRAM: 2003 DODGE TO PRESENT

AND 2001 CHEVY TO PRESENT

Wiring Schematic

Explanation

* NOTE: Observe all vehicle manufacturer recommendations when

working with or connecting to vehicle electrical systems. These wiring

instructions were created for trucks using separate brake and turn

signal lights. Keep all lights turned off when making connections.

The wiring is installed starting on the right side of the

headache rack, running through it and picking up the left

side. It then travels back to the center of the bed where there

is a 6 pin connection. The center harness is connected here

and runs back to the tail skirt where there is another 6 pin

connection for the rear skirt harness. Before the rear

Page is loading ...

CM Truck Beds SS Bed Owner's manual

Brand: CM Truck Beds

Model: SS Bed

Type: Owner's manual

This manual is also suitable for

Download PDF

report

CM Truck Beds SS Bed Owner's manual

This manual is also suitable for

CM Truck Beds SS Bed Owner's manual

Related papers

Other documents