S4 S1
S2
INSTRUCTION MANUAL
ISLAND COOKER HOOD - SANTINA
General safety and installation conditions:
When installing the appliance, follow the conditions and guidelines given in this
operating manual.
This appliance is intended for domestic use only. In case of commercial use in
food business, warranty conditions change.
Do not remove the plug from the power socket by pulling the cord.
The power cord must not touch any hot surface.
Do not turn the appliance on if the power cord is damaged.
The cooker hood, if used to extract cooking fumes outside, should be connected
to an appropriate
ventilation duct (do not connect it to flues, smoke or exhaust ducts which are in
use).
The manufacturer assumes no responsibility for any damage caused by the
installation not conforming to the operating manual.
Any changes made in the structure of the hood by unauthorized persons will
result in the exclusion of the liability of the manufacturer.
If the cooker hood is used simultaneously with devices burning gas or other
fuels, the room should be appropriately ventilated (not applicable in the case of
closed circulating system).
Do not use naked flame directly under the cooker hood,
If the non-detachable power cord is damaged, it should be replaced with a
special cord available from the manufacturer or a specialized repair shop.
The exhaust air from the hood must not be discharged into a flue used for
discharging exhaust fumes from appliances burning gas or other fuels (not
applicable in the case of closed circulation system).
Before connecting the cooker hood to the mains power supply and checking its
correct functioning, always check if the power cord is properly installed and has
not been pinched by the hood during installation.
Before cleaning, unplug the power cord.
Cleaning not carried out in accordance with the manual constitutes a fire hazard.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge of the appliance, unless they are given
supervision or instructions according to the operating manual by persons
responsible for their safety.
Purpose and operations
The hood is intended for operation in a filter mode as a closed circulation system.
Electrical connection
The mains voltage must comply with the specifications given on the rating plate inside the hood. If the
hood is equipped with a plug should be put in a plug socket meets the requirements of the applicable
regulations and located in an easily accessible place. If the hood is not equipped with a plug, the
installation of the hood should be entrusted to the person with the appropriate permissions.
Cleaning the hood
Before any operations involving the maintenance device, turn off the hood. The device should be cleaned
using specialized agents for surface made of stainless steel. The hood should be cleaned with mild, not
abrasive cleaners. Regular maintenance will improve the operation of the hood.
Caution: DO NOT USE ALCOHOL!!!
Grease filters
The cooker hood is equipped with two aluminium filters. The filter is removed by moving the locks in the
direction indicated by the arrow (Fig. S1). The filter should be cleaned manually in the following manner:
immerse it for 15 minutes in water mixed with mild detergent at the temperature of 40-50°C. After 15
minutes, start washing the filter and rinse it carefully. The filter must be completely dry before it is put back
in the hood. If the filter is not cleaned regularly, the performance of the hood decreases and the fire risk
increases. If washed in a dishwasher, the filter may become discoloured, but this does not affect its
filtering properties.
The carbon filter (only for closed loop - fig. S4)
The hood should be equipped with 2 carbon filters. Filters should be placed on the turbine housing, as
illustrated in Figure S5. In this case, the purified air is discharged back into the room. The Santina cooker
hood should not be connected to the ventilation ducts. In order to ensure proper operation of the hood and
effectively reduce odours should replace carbon filters regularly (every 3 to 6 months) depending on the
intensity of use of the hood.
Replacing the aluminium filter - Fig. S1
Dimensions of the hood - Fig. S2
Mounting the hood - Figure S3
Replacing carbon filters - Fig. S4
The symbol placed on a product or on the accompanying documents means that this product
may not be treated as household waste. In order to dispose of the appliance, you should take it
to an appropriate collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local regulations concerning waste disposal.
For more information about utilization, scrapping and recycling of this appliance, please contact
your local authorities, waste disposal facility or the store where you purchased the product.
Electronic Controls
The control panel of the hood is located on the front of the hood. The individual functions are marked with symbols.
The hood is equipped with a timer. After registering 35hrs of operation of the hood, the timer indicates the recommended
aluminium filter cleaning by flashing the letter F on the display. To delete the character F on the display, press and hold the "-"
continuously for approx. 8 seconds.
In accordance with the EU Regulation 66/2014 the hood is equipped with an automatic self-timer, which will lower the level of
turbine from the fourth to third after 5 minutes.
Control the operation of the turbine
• turbine has 3 stages of work + intensive mode (turbo)
„” - infrared sensor for control remote
„Θ” - activates the turbine with the speed with which the hood work before shutting down.
- turns off the turbine
- holding for 10 seconds locks the buttons which allows safe cleaning, the display shows a single "dot"
- pressing and holding the button for 10 seconds reactivates the control panel
„ - " - turns on the turbine at minimum speed turbine
- reduces the speed of the turbine,
„” - the display shows the speed of the turbine from 1 to 4
„+” - starts the turbine at maximum speed
- increases the speed of the turbine
Lighting
"light bulb icon" - pressing the button to turn on lighting, pressing the button again turns off the lights
Auto timer
After 2 hours from turning on or the last change of speed, the turbine will automatically shut itself off.
Remote control
Field with icon
„fan”– turns on/off the fan
„+” – increase the speed of the turbine
„–“ – reduces the speed of the turbine
Field with light bulb icon
„light bulb icon” – turns on/off lights
„+” „– „ – inactive
„ON” – switches on decorative lighting
„OFF” – turns off decorative lighting
Buttons with arrow up / down - increase / decrease the intensity of decorative lighting
Strobe – turns on decorative lights flicker
Fade – lowers intensity of decorative lighting
Coloured buttons allows selecting of decorative lighting colour
The magnet on the back of the remote allows you to put it on the cover of the hood and other steel surfaces.
Ways to reduce the impact on the environment of the cooking process:
In order to reduce energy consumption should be cooked in pots under cover.
Aluminium grease filters must be kept clean. The recommended operating time between the aluminium filter cleanings is 35h
operation of the hood.
The level of turbine operation during cooking should always be set at the minimum speed that will allow for the removal of fumes at
the current intensity of cooking.
Technical data in this manual and accompanying labels were obtained by performing measurements and calculations in
accordance with the requirements of EU Regulation 65/2014 and 66/2014.
A
B
C
S3
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Kuppersberg SLIMLUX S 90 GB User manual
-
-
-
Amica OKP6655S User manual
-
Seenergy HIT PLUS User manual
-
CONTINENTAL EDISON CEH90ST User manual
-
-
-
Hoover HVSD9800B User manual
-
ROSIERES RVSD970PN User manual
