Ancona AN-4528 widespread lavatory bathroom faucet is a versatile and stylish addition to any bathroom. This faucet features:
- Durable construction: Made of high-quality materials, this faucet is built to last.
- Water-saving design: The 1.2 gpm flow rate helps to conserve water without sacrificing performance.
- Easy installation: The included instructions and all necessary hardware make installation a breeze.
- Versatile design: The widespread design allows for easy installation in a variety of bathroom configurations.
- Stylish finish: The polished chrome finish complements any bathroom décor.
Ancona AN-4528 widespread lavatory bathroom faucet is a versatile and stylish addition to any bathroom. This faucet features:
- Durable construction: Made of high-quality materials, this faucet is built to last.
- Water-saving design: The 1.2 gpm flow rate helps to conserve water without sacrificing performance.
- Easy installation: The included instructions and all necessary hardware make installation a breeze.
- Versatile design: The widespread design allows for easy installation in a variety of bathroom configurations.
- Stylish finish: The polished chrome finish complements any bathroom décor.
© ®
Widespread Lavatory Bathroom Faucet
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Helpful Information
Scarlett
2021-06-25 MAAN4528-2
SEALED-TUBE
Please keep the tools for future use!
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
WARNING:
Attention:
Important
For easy installation, you will need:
• To read all the installation instructions completely before beginning.
• To read all the warning, attention and maintenance information.
• To purchase the proper supply lines.
Tighten connection with two wrenches to prevent
damage to tube body. Be careful not to bend the
stem as this will void the product warranty.
Connect to water supply lines with either
risers with the coupling nuts or
supplied tube head interior connector or
A. B. C.
STANDARDS
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
LISTED IAPMO/cUPC
1.2 gpm/4.5 L/min
•
•
•
•
Faucet Installation
1
2
Tools might be applied to the following places:
Installation size map
3
Position the body with o-ring on the installation
surface as shown and secure it with gasket
assembly and tighten the lock nut with adjustable
wrench.
Position the handle on installation
surface as shown, secure it with fixing
kit and tighten the screw with
screwdriver. Repeat the above steps
for the other handle.
Caution: please be careful with the
position of hot and cold handles.
Position the flexible hose and fix it
to the faucet as shown with clamp
spring.
2.4 in.
(6.1 cm)
1/2-14NPSM
1 3/16 - 1 3/8 in.
(3 - 3.5 cm)
2.3 in.
(5.9 cm)
3.2 in.
(8.1 cm)
4.1 in.
(10.4 cm)
4.3 in. (11 cm)
4 in.
(10.2 cm)
7.3 in. (18.6 cm)
6.5 in.
(16.5 cm)
4 in. (10.1 cm) 4 in. (10.1 cm)
5.3 in.
(13.5 cm)
Max
1.1 in.
(3 cm)
4
5
WARNING:
DON'T OVERTIGHTEN!
Connect the water supply lines to
faucet and water supply valves,
then tighten it with wrench.
Warning: The water supply
valves mentioned above are not
included, please purchase them
at your local hardware store.
6
Turn the faucet handle all the way
on, turn on hot and cold water
supply and flush water lines for
one minute. Reinstall aerator by
hand.
Check all connections at arrows for
leaks, retighten if necessary.
BUT DON’T OVERTIGHTEN
1 Clean it with water and dry it with soft cloth.
2 Clean the product with gentle liquid or glass cleaner.
3 Don't use acid cleaner.
4 Don't clean with abrasive material, abrasive paper or knife.
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
Checking and Testing
HOT
COLD
Parts list
Maintenance:
Simply rinse the surface with clear water or
mild liquid detergents (if necessary). Dry the
faucet with a clean soft cotton cloth. Do not
use any cleaning agents containing acids
polish abrasives or harsh cleaners.
Maintenance
1
2
3
Disassemble the screw with
allen key
, take out the handle
and base
.
If faucet leaks from the handle or drips from spout, please replace cartridge following the steps:
Unscrew the old cartridge with
Adjustable Wrench, then take it
out.
Place a new cartridge in the
cartridge seat, then screw the base
and assemble the handle by
securing the screws. Repeat the
above steps for the other cartridge
if necessary.
1
2
3
4
1
2
NO. PART NAME
Screw1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Screw
Handle
Handle base
Screw nut
O-ring
Handle spline
Cartridge
Inlet hose
O-ring
Inlet tube
O-ring
O-ring
Washer
Gasket
Screw
Screw
Clamp spring
Aerator
20
Supply line
21
22
23
24
25
26
27
28
29
Spout body
Spout base
O-ring
Screw
Inlet hose
O-ring
Washer
Gasket
Screw nut
30
Cartridge
31
32
33
34
Clamp spring
Connect hose
Allen key
Aerator wrench
-
1
-
2
-
3
-
4
Ancona AN-4528 widespread lavatory bathroom faucet is a versatile and stylish addition to any bathroom. This faucet features:
- Durable construction: Made of high-quality materials, this faucet is built to last.
- Water-saving design: The 1.2 gpm flow rate helps to conserve water without sacrificing performance.
- Easy installation: The included instructions and all necessary hardware make installation a breeze.
- Versatile design: The widespread design allows for easy installation in a variety of bathroom configurations.
- Stylish finish: The polished chrome finish complements any bathroom décor.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Roswell 106123-BAF-PC Installation guide
-
-
-
Unbranded LSAZ055-095B Installation guide
-
ANZZI LSAZ074-097B Installation guide
-
-
ANZZI Bravo L-AZ030 Installation guide
-
ANZZI LSAZ083-096 Installation guide
-
-