Independence Flag R662 Installation guide

Brand
Independence Flag
Model
R662
Type
Installation guide

Independence Flag R662 is a solar-powered flagpole light designed to illuminate the colors of pride. It is easy to install and can be used on flagpoles ranging from 5' to 7' and .75" to 1.25" in diameter. The light features an "L" shaped rod that allows for easy adjustment of the solar panel for maximum sun exposure. It also has a slotted clamp that allows for easy positioning of the light on the flagpole. The light will turn on and off automatically each day, and it will require one full day of sunlight to fully recharge the batteries.

Independence Flag R662 is a solar-powered flagpole light designed to illuminate the colors of pride. It is easy to install and can be used on flagpoles ranging from 5' to 7' and .75" to 1.25" in diameter. The light features an "L" shaped rod that allows for easy adjustment of the solar panel for maximum sun exposure. It also has a slotted clamp that allows for easy positioning of the light on the flagpole. The light will turn on and off automatically each day, and it will require one full day of sunlight to fully recharge the batteries.

★
P.O. Box 526
★
105A Industrial Drive
★
Gilbertsville, PA 19525
★
Phone 800.976.4201
★
Fax 800.862.7706
★
www.IndependenceFlag.com
★
U.S. Flag Code states that it is the universal custom to display the flag only from sunrise to sunset
on buildings and on stationary flagstaffs in the open. However, when a patriotic effect is desired, the flag
may be displayed twenty-four hours a day if properly illuminated during the hours of darkness.
Residential Solar Flagpole Light
Lighting the Colors of Pride
Independence Flag # R662
Solar Light Assembly Instructions
1. Remove Solar Light from the bubble wrap protective packaging.
2. Grasp the “L” shaped rod directly behind the ball and attach the solar panel by forcefully
snapping it on to the ball end of the rod.
3. Using a flat screwdriver, unscrew the slotted clamp until the end can be separated from the
adjustment screw.
4. Insert the loose end of the slotted strap through the 2 slots on the mounting bracket.
5. Place the end of the slotted strap back into the screw adjustment housing and tighten the
screw until the strap appears under the adjustment screw head.
6. Slide the slotted clamp on to the flagpole and position it approximately 20" from the bottom of
the pole.
7. Tighten the screw adjuster just enough to hold the solar light in place. Later, you can reposition
the solar light for maximum illumination of the flag.
8. If you are installing the light on a 1" or 1 1/4" flagpole, please skip the next step.
9. Note: If you are installing the solar light on a 3/4" diameter flagpole, the use of the black
neoprene adapter will be required. Determine the most efficient position of the solar light on
the pole, to properly illuminate the flag. Remove the protective strip from the black neoprene
adapter and place the adhesive side to the pole, at the location that you have selected.
10. Install the flagpole into your bracket and tighten to secure the pole.
11. Adjust the solar light housing so that it is pointing towards the flag. Locate the housing
adjustment screw, found on top of the solar light housing and tighten the screw to
keep the housing in place.
12. Holding the “L” shaped rod, adjust the solar panel to a position that will
capture the maximum sun exposure.
13. Remove the protective film from the face of the solar panel.
14. Your light will require one full day of sunlight to fully recharge the
batteries.
15. Once properly charged, the solar light will turn on and off automatically
each day.
16. When the light is illuminated, you may readjust it for maximum illumination of
the flag by loosening the adjustment clamp, repositioning the light and
retightening the clamp.
5/21/12rev
For 5' to 7' poles,
from .75" to 1.25"
in diameter
  • Page 1 1

Independence Flag R662 Installation guide

Brand
Independence Flag
Model
R662
Type
Installation guide

Independence Flag R662 is a solar-powered flagpole light designed to illuminate the colors of pride. It is easy to install and can be used on flagpoles ranging from 5' to 7' and .75" to 1.25" in diameter. The light features an "L" shaped rod that allows for easy adjustment of the solar panel for maximum sun exposure. It also has a slotted clamp that allows for easy positioning of the light on the flagpole. The light will turn on and off automatically each day, and it will require one full day of sunlight to fully recharge the batteries.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents