Scotsman Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01 Operating instructions

Scotsman
Brand
Scotsman
Model
Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01
Type
Operating instructions

Scotsman Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01

This guide provides instructions for placing a Scotsman ice machine on the BH1100, BH1300, or BH1600 upright ice storage bin. These bins come with four plastic filler panels to cover the hole in the bin's top when an ice machine is not installed. The panels can be combined to create different configurations to accommodate various ice machine sizes and models.

For example:

  • For a single 30" cuber or flaker on a BH1100 bin, use two 9" panels, one on each end.
  • For two 22" cubers on a BH1100 bin, use one 9" panel between the two ice machines.

Scotsman Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01

This guide provides instructions for placing a Scotsman ice machine on the BH1100, BH1300, or BH1600 upright ice storage bin. These bins come with four plastic filler panels to cover the hole in the bin's top when an ice machine is not installed. The panels can be combined to create different configurations to accommodate various ice machine sizes and models.

For example:

  • For a single 30" cuber or flaker on a BH1100 bin, use two 9" panels, one on each end.
  • For two 22" cubers on a BH1100 bin, use one 9" panel between the two ice machines.
for the placement of a Scotsman ice machine on the BH1100,
BH1300 or BH1600 upright ice storage bin.
These three bins are supplied with four plastic filler panels, two 9 inch and two 13.5
inch. The top of the bin has a large hole that must be covered by the ice machine and
/or one or more panels. These panels can be combined to cover the space next to an
ice machine. See the proper page for an illustration of which panels to use and where to
place them.
Custom Bin Tops required for CME686, CME810, EH222, MAR1400, MAR2000, two
30” units or a stack of two CME cubers on BH1300 or BH1600.
Note: Two 30” units side by side must not be air cooled. Two 21” or 22” air cooled units
side by side must be separated and have adequate air flow.
There are no means for securing the ice machine to the bin’s top.
Instructions
Table of Contents
BH1100 - 48” Cuber - single or stacked ,,,,,,,,,,,,,,,,,,, Page 2
BH1100 - Single 30” Cuber or Flaker or Nugget ,,,,,,,,,,,,,,, Page 3
BH1100 - Single 22” Cuber ,,,,,,,,,,,,,,,,,,,,,,,,,, Page 4
BH1100 - Two 22” Cubers ,,,,,,,,,,,,,,,,,,,,,,,,,, Page 5
BH1100 - Single 21” Flake or Nugget ,,,,,,,,,,,,,,,,,,,, Page 6
BH1100 - Two 21” Flake or Nugget ,,,,,,,,,,,,,,,,,,,,,, Page 7
BH1100 - Single 42” Flake or Nugget ,,,,,,,,,,,,,,,,,,,,, Page 8
BH1300 or BH1600 - 48” cuber ,,,,,,,,,,,,,,,,,,,,,,, Page 9
BH1300 or BH1600 single 30” cuber or flaker or nugget ,,,,,,,,,,, Page 10
BH1300 or BH1600 single 22” cuber ,,,,,,,,,,,,,,,,,,,,, Page 11
BH1300 or BH1600, two 22” cubers ,,,,,,,,,,,,,,,,,,,,, Page 12
BH1300 or BH1600, single 21” flaker or nugget ,,,,,,,,,,,,,,, Page 13
BH1300 or BH1600 - two 21” flakers or nugget ,,,,,,,,,,,,,,,, Page 14
BH1300 or BH1600 - single 42” flaker or nugget ,,,,,,,,,,,,,,, Page 15
17-3011-01
BH1100 - 48” Cuber - single or stacked
No inserts are needed. Place the ice machine over the hole in the bin’s top.
Page 2
BH1100 - Single 30” Cuber or Flaker or Nugget
Use Two 9” panels, one on each end.
Page 3
BH1100 - Single 22” Cuber
Use Two 13.5” panels, one on each end.
Page 4
BH1100 - Two 22” Cubers
Use one 9” panel, located between the two ice machines.
Page 5
BH1100 - Single 21” Flake or Nugget
Use two 13.5” panels, one on each end.
Page 6
BH1100 - Two 21” Flake or Nugget
Use single 9” panel, between the two ice machines.
Page 7
BH1100 - Single 42” Flake or Nugget
Use single 9” panel on the left end.
Page 8
BH1300 or BH1600 - 48” cuber
No panels needed.
Page 9
BH1300 or BH1600 single 30” cuber or flaker or nugget
Use a 9” panel on each end.
Page 10
BH1300 or BH1600 single 22” cuber
Use a 13.5” panel on each end.
Page 11
BH1300 or BH1600, two 22” cubers
Place cubers on ends of hole, place 9” panel in center.
Page 12
BH1300 or BH1600, single 21” flaker or nugget
Place a 13.5” panel on each end.
Page 13
BH1300 or BH1600 - two 21” flakers or nugget
Place a single 9” panel in between the two ice machines.
Page 14
BH1300 or BH1600 - single 42” flaker or nugget
Place a single 9” panel on the left end of the hole.
Page 15
Scotsman Ice Systems
800-533-6006
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Scotsman Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01 Operating instructions

Scotsman
Brand
Scotsman
Model
Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01
Type
Operating instructions

Scotsman Placement of a Scotsman Ice Machine on the BH1100, BH1300, or BH1600 Ice Storage Bin - 17-3011-01

This guide provides instructions for placing a Scotsman ice machine on the BH1100, BH1300, or BH1600 upright ice storage bin. These bins come with four plastic filler panels to cover the hole in the bin's top when an ice machine is not installed. The panels can be combined to create different configurations to accommodate various ice machine sizes and models.

For example:

  • For a single 30" cuber or flaker on a BH1100 bin, use two 9" panels, one on each end.
  • For two 22" cubers on a BH1100 bin, use one 9" panel between the two ice machines.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents