Grizzly G0459 Owner's manual

Category
Power sanders
Type
Owner's manual

This manual is also suitable for

MODEL G0459/G0459P
12" DRUM SANDER
OWNER’S MANUAL
COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED JULY, 2014 (ST)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MANUFACTURED SINCE 7/11) #BL7307 PRINTED IN TAIWAN
177335
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION ............................................... 2
Manual Accuracy ........................................... 2
Contact Info.................................................... 2
Machine Description ...................................... 2
Identification ................................................... 3
Machine Data Sheet ...................................... 4
SECTION 1: SAFETY ....................................... 8
Safety Instructions for Machinery .................. 8
Additional Safety for Drum Sanders ............ 10
SECTION 2: POWER SUPPLY ...................... 11
SECTION 3: SETUP ....................................... 13
Needed for Setup ......................................... 13
Unpacking .................................................... 13
Inventory ...................................................... 13
Site Considerations ...................................... 14
Mounting ...................................................... 15
Installing Crank Handle ................................ 15
Dust Collection ............................................. 16
Power Connection........................................ 16
Test Run ...................................................... 17
Recommended Adjustments ........................ 17
SECTION 4: OPERATIONS ........................... 18
Operation Overview ..................................... 18
Basic Controls .............................................. 19
Disabling & Locking Switch.......................... 19
Sanding Tips ................................................ 20
Stock Inspection and Requirements ............ 20
Depth of Cut ................................................. 21
Variable Speed ............................................ 22
Sanding ........................................................ 22
Choosing Sandpaper ................................... 23
Paper Replacement ..................................... 23
SECTION 5: ACCESSORIES ......................... 24
SECTION 6: MAINTENANCE ......................... 25
Schedule ...................................................... 25
Cleaning ....................................................... 25
Lubrication ................................................... 25
SECTION 7: SERVICE ................................... 27
Troubleshooting ........................................... 27
Gauge Blocks............................................... 30
V-Belt Service .............................................. 30
Conveyor Tensioning & Tracking................. 32
Drum Adjustments ....................................... 33
Pressure Roller Height ................................. 35
Scale Pointer Calibration ............................. 36
Table Lift Screws ......................................... 37
Conveyor Belt Replacement ........................ 38
Changing Motor Brushes ............................. 42
SECTION 8: WIRING ...................................... 43
Wiring Safety Instructions ............................ 43
Electrical Components ................................. 44
Wiring Diagram ............................................ 45
SECTION 9: PARTS ....................................... 46
Frame ........................................................... 46
Frame Parts List .......................................... 47
Drum ............................................................ 48
Conveyor ...................................................... 49
Conveyor Parts List ..................................... 50
Label Placement .......................................... 50
WARRANTY AND RETURNS ........................ 53
-2-
Model G0459/G0459P (Mfg. 7/11+)
INTRODUCTION
We stand behind our machines. If you have any
service questions, parts requests or general ques-
tions about the machine, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
C
/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Contact Info
A drum sander is used to remove surface material
from stock using an abrasive belt that is wrapped
tightly around a drum.
A conveyor pulls the workpiece toward the sand-
ing drum while pressure rollers hold the workpiece
steady, so the sanding drum can remove a thin
layer from the top of the workpiece.
On the G0459/G0459P, a crank handle is used to
control cutting depth and a variable speed knob
adjusts the conveyor speed for the specific type
of workpiece and finish.
The only difference between the Model G0459
and G0459P is the paint color.
Machine Description
Manual Accuracy
We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings, and
photographs of the machine we used when writ-
ing this manual. However, sometimes errors do
happen and we apologize for them.
Also, owing to our policy of continuous improve-
ment, your machine may not exactly match the
manual. If you find this to be the case, and the dif-
ference between the manual and machine leaves
you in doubt, check our website for the latest
manual update or call technical support for help.
Before calling, find the manufacture date of your
machine by looking at the date stamped into the
machine ID label (see below). This will help us
determine if the manual version you received
matches the manufacture date of your machine.
For your convenience, we post all available man-
uals and manual updates for free on our website
at www.grizzly.com. Any updates to your model
of machine will be reflected in these documents
as soon as they are complete.
Manufacture Date
of Your Machine
Model G0459/G0459P (Mfg. 7/11+)
-3-
Figure 1. Front view, Model G0459.
Identification
Top Cover
Cover Lock Knob
Dust Port
Crank Handle
DC Feed
Motor
Thermal
Circuit
Breaker
On/Off
Switch
Drum
Sander
Frame
Variable Speed
Control
Conveyor Belt
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
Front Elevation
Chain Guard
-4-
Model G0459/G0459P (Mfg. 7/11+)
The information contained herein is deemed accurate as of 3/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 2
Model G0459
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0459 12" 1‐1/2 HP BABY DRUM SANDER
Product Dimensions:
Weight.............................................................................................................................................................. 139 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................................... 27 x 24 x 27 in.
Footprint (Length x Width)..................................................................................................................... 22-1/4 x 12 in.
Shipping Dimensions:
Type..................................................................................................................................................... Cardboard Box
Content........................................................................................................................................................... Machine
Weight.............................................................................................................................................................. 166 lbs.
Length x Width x Height....................................................................................................................... 26 x 27 x 27 in.
Must Ship Upright................................................................................................................................................... Yes
Electrical:
Power Requirement........................................................................................................... 115V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 115V
Full-Load Current Rating..................................................................................................................................... 13.3A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length............................................................................................................................................... 11 ft.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 5-15
Switch Type.................................................................................................................... ON/OFF Push Button Switch
Motors:
Feed
Horsepower............................................................................................................................................. 1/8 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 0.3A
Speed.............................................................................................................................................. 5 – 55 RPM
Type..................................................................................................................................................... Universal
Power Transfer ............................................................................................................................... Direct Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................................................................ N/A
Main
Horsepower............................................................................................................................................. 1.5 HP
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 13A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer ............................................................................................................................... V-Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External
Model G0459/G0459P (Mfg. 7/11+)
-5-
The information contained herein is deemed accurate as of 3/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 2
Model G0459
Main Specifications:
Operation Information
Number of Sanding Heads............................................................................................................................... 1
Maximum Board Width.............................................................................................................................. 12 in.
Minimum Board Width................................................................................................................................. 2 in.
Maximum Board Thickness................................................................................................................... 3-1/2 in.
Minimum Board Thickness....................................................................................................................... 1/8 in.
Minimum Board Length................................................................................................................................ 8 in.
Sandpaper Speed.............................................................................................................................. 2127 FPM
Conveyor Feed Rate.................................................................................................................. 2.5 – 17.3 FPM
Sandpaper Length..................................................................................................................................... 70 in.
Sandpaper Width......................................................................................................................................... 3 in.
Drum Information
Infeed Sanding Drum Type................................................................................................................. Aluminum
Infeed Sanding Drum Size........................................................................................................................... 4 in.
Construction
Conveyor Belt......................................................................................................................................... Rubber
Body........................................................................................................................................................... Steel
Paint Type/Finish....................................................................................................................... Powder Coated
Other Related Information
Sanding Belt Tension..................................................................................................................... Hook & Loop
Number of Pressure Rollers............................................................................................................................. 2
Pressure Roller Type.............................................................................................................................. Rubber
Pressure Roller Size.............................................................................................................................. 1-3/8 in.
Conveyor Belt Length.......................................................................................................................... 49-3/4 in.
Conveyor Belt Width............................................................................................................................ 12-1/4 in.
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size........................................................................................................................................ 2-1/2 in.
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ........................................................................................................ 15 Minutes
Serial Number Location .................................................................................................................................. ID Label
ISO 9001 Factory .................................................................................................................................................... No
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................................................... Yes
Features:
Hoop & Loop Sanding Belt Tension/Sandpaper
Industrial-Duty Rubber Conveyor Belt
2-1/2" Dust Port
Variable Speed Conveyor
V-Belt Main Motor; Direct Drive Feed Motor
4" Aluminum Sanding Drum
Green Powder Coated Paint
Steel Dust Scoop Maximizes Dust Collection Efficiency
Two Adjustable Pressure Rollers
Thickness Scale
Welded Steel Construction
Side Handles for Portability
-6-
Model G0459/G0459P (Mfg. 7/11+)
The information contained herein is deemed accurate as of 3/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 2
Model G0459P
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0459P 12" BABY DRUM SANDER, POLAR BEAR
SERIES
Product Dimensions:
Weight.............................................................................................................................................................. 139 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................................... 27 x 24 x 27 in.
Footprint (Length x Width)..................................................................................................................... 22-1/4 x 12 in.
Shipping Dimensions:
Type..................................................................................................................................................... Cardboard Box
Content........................................................................................................................................................... Machine
Weight.............................................................................................................................................................. 166 lbs.
Length x Width x Height....................................................................................................................... 27 x 26 x 27 in.
Must Ship Upright................................................................................................................................................... Yes
Electrical:
Power Requirement........................................................................................................... 115V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 115V
Full-Load Current Rating..................................................................................................................................... 13.3A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length............................................................................................................................................... 11 ft.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 5-15
Switch Type.................................................................................................................... ON/OFF Push Button Switch
Motors:
Feed
Horsepower............................................................................................................................................. 1/8 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 0.3A
Speed.............................................................................................................................................. 5 – 55 RPM
Type..................................................................................................................................................... Universal
Power Transfer ............................................................................................................................... Direct Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................................................................ N/A
Main
Horsepower............................................................................................................................................. 1.5 HP
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 13A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer ............................................................................................................................... V-Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External
Model G0459/G0459P (Mfg. 7/11+)
-7-
The information contained herein is deemed accurate as of 3/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 2
Model G0459P
Main Specifications:
Operation Information
Number of Sanding Heads............................................................................................................................... 1
Maximum Board Width.............................................................................................................................. 12 in.
Minimum Board Width................................................................................................................................. 2 in.
Maximum Board Thickness................................................................................................................... 3-1/2 in.
Minimum Board Thickness....................................................................................................................... 1/8 in.
Minimum Board Length................................................................................................................................ 8 in.
Sandpaper Speed.............................................................................................................................. 2127 FPM
Conveyor Feed Rate.................................................................................................................. 2.5 – 17.3 FPM
Sandpaper Length..................................................................................................................................... 70 in.
Sandpaper Width......................................................................................................................................... 3 in.
Drum Information
Infeed Sanding Drum Type................................................................................................................. Aluminum
Infeed Sanding Drum Size........................................................................................................................... 4 in.
Construction
Conveyor Belt......................................................................................................................................... Rubber
Body........................................................................................................................................................... Steel
Paint Type/Finish....................................................................................................................... Powder Coated
Other Related Information
Sanding Belt Tension..................................................................................................................... Hook & Loop
Number of Pressure Rollers............................................................................................................................. 2
Pressure Roller Type.............................................................................................................................. Rubber
Pressure Roller Size.............................................................................................................................. 1-3/8 in.
Conveyor Belt Length.......................................................................................................................... 49-3/4 in.
Conveyor Belt Width............................................................................................................................ 12-1/4 in.
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size........................................................................................................................................ 2-1/2 in.
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ........................................................................................................ 15 Minutes
Serial Number Location ................................................................................................................... ID Label on Front
ISO 9001 Factory .................................................................................................................................................... No
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................................................... Yes
Features:
Hoop & Loop Sanding Belt Tension/Sandpaper
Industrial-Duty Rubber Conveyor Belt
2-1/2" Dust Port
Variable Speed Conveyor
V-Belt Main Motor; Direct Drive Feed Motor
4" Aluminum Sanding Drum
White Powder Coated Paint
Steel Dust Scoop Maximizes Dust Collection Efficiency
Two Adjustable Pressure Rollers
Thickness Scale
Welded Steel Construction
Side Handles for Portability
-8-
Model G0459/G0459P (Mfg. 7/11+)
ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST.
Always discon-
nect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are not approved safety glasses.
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY
Model G0459/G0459P (Mfg. 7/11+)
-9-
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
coverlonghair.Wear non-slipfootweartoavoid
accidentalslips,whichcouldcauselossofwork-
piececontrol.
hAzARdOus dusT. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratorydamage. Be aware of dust
hazardsassociatedwitheachworkpiecematerial,
andalwayswearaNIOSH-approvedrespiratorto
reduceyourrisk.
hEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
withouthearing protectioncan cause permanent
hearingloss.
REMOVE AdJusTING TOOLs. Tools left on
machinery can become dangerous projectiles
uponstartup.Neverleavechuckkeys,wrenches,
or any other tools on machine. Always verify
removalbeforestarting!
INTENdEd usAGE. Only use machine for its
intendedpurposeandnevermakemodifications
not approved by Grizzly. Modifying machine or
using it differently than intended may result in
malfunctionormechanicalfailurethatcanleadto
seriouspersonalinjuryordeath!
AWKWARd POsITIONs. Keep proper footing
andbalanceatalltimeswhenoperatingmachine.
Donotoverreach!Avoidawkwardhandpositions
that make workpiece control difficult or increase
the
riskofaccidentalinjury.
ChILdREN & BYsTANdERs. Keepchildrenand
bystandersatasafedistancefromtheworkarea.
Stopusingmachineiftheybecomeadistraction.
GuARds & COVERs.Guardsandcoversreduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged,andworkingcorrectly.
FORCING MAChINERY.Donotforcemachine.
Itwill do the jobsaferand better at therate for
whichitwasdesigned.
NEVER sTANd ON MAChINE. Serious injury
may occur if machine is tipped or if the cutting
toolisunintentionallycontacted.
sTABLE MAChINE. Unexpectedmovementdur-
ing operation greatly increases risk of injury or
lossofcontrol.Beforestarting,verifymachineis
stableandmobilebase(ifused)islocked.
usE RECOMMENdEd ACCEssORIEs.Consult
thisowner’smanualorthemanufacturerforrec-
ommended accessories. Using improper acces-
sorieswillincreasetheriskofseriousinjury.
uNATTENdEd OPERATION. To reduce the
risk of accidental injury, turn machine off and
ensure all moving parts completely stop before
walking away. Never leave machine running
whileunattended.
MAINTAIN WITh CARE.Followallmaintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is
improperly maintained could malfunction,
leadingtoseriouspersonalinjuryordeath.
ChECK dAMAGEd PARTs. Regularly inspect
machine for any condition that may affect safe
operation.Immediatelyrepairorreplacedamaged
ormis-adjustedpartsbeforeoperatingmachine.
MAINTAIN POWER CORds. When disconnect-
ing cord-connected machines from power, grab
andpulltheplugNOTthecord.Pullingthecord
may damage the wires inside. Do not handle
cord/plugwithwethands.Avoidcorddamageby
keepingitawayfromheatedsurfaces,hightraffic
areas,harshchemicals,andwet/damplocations.
EXPERIENCING dIFFICuLTIEs. If at any time
youexperiencedifficultiesperformingtheintend-
edoperation,stopusingthemachine!Contactour
TechnicalSupportat(570)546-9663.
-10-
Model G0459/G0459P (Mfg. 7/11+)
Additional Safety for Drum Sanders
FEEDING STOCK. Do not stand in the direct
path of a workpiece at the infeed end when feed-
ing your stock. Never sand more than one piece
of stock at a time. DO NOT jam the workpiece
into the machine during operation. Firmly grasp
the workpiece in both hands and ease it into the
machine using light pressure.
MINIMUM STOCK DIMENSIONS. Do not sand
any stock thinner than
1
8", narrower than 2", or
shorter than 8". Do not sand thin stock by using a
“dummy” board under your workpiece.
SAFETY COVERS. All covers must be closed
and in place before starting machine.
CLOTHING. Do not wear loose clothing while
operating this machine. Roll up or button long
sleeves at the cuff.
HAND PROTECTION. Do not place hands near,
or in contact with, sanding drum during operation.
DO NOT allow fingers to get pinched between
board and conveyor belt during operation. This
may pull the operator’s hand into the machine and
cause serious injury!
DUST COLLECTION SYSTEM. Never operate
the sander without an adequate dust collection
system in place and running.
INSPECTING WORKPIECES. Always inspect
every workpiece for nails, staples, knots, and
other imperfections that could be dislodged and
thrown from the machine during sanding opera-
tions. Do not use workpieces with these defects.
EXPERIENCING DIFFICULTIES. Any problem,
with the exception of conveyor belt tracking, that
is concerned with any moving parts or accesso-
ries, must be investigated and corrected with the
power disconnected, and after all moving parts
have come to a complete stop.
MAINTENANCE AND ADJUSTMENTS. Never
attempt to adjust conveyor belt tracking when the
sanding drum is running.
Perform machine inspections and maintenance
service promptly when called for. Disconnect
power before performing maintenance or adjust-
ments to the sander.
RESPIRATOR AND SAFETY GLASSES. Always
wear a respirator and safety glasses while operat-
ing the machine. Dust and chips are created when
sanding. Some debris will be ejected, becoming
hazards to the eyes and lungs.
Model G0459/G0459P (Mfg. 7/11+)
-11-
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrican or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Full-Load Current Rating at 115V... 13.3 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Circuit Requirements
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage ........................................ 115V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps
-12-
Model G0459/G0459P (Mfg. 7/11+)
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine.
If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require-
ments:
Minimum Gauge Size ...........................14 AWG
Maximum Length (Shorter is Better).......50 ft.
Grounding & Plug Requirements
Figure 2. Typical 5-15 plug and receptacle.
Grounding Pin
Neutral Hot
5-15 PLUG
GROUNDED
5-15 RECEPTACLE
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug providedif
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This machine is equipped with a power cord that
has an equipment-grounding wire and a ground-
ing plug (similar to the figure below). The plug
must only be inserted into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
Model G0459/G0459P (Mfg. 7/11+)
-13-
SECTION 3: SETUP
The following are needed to complete the setup
process, but are not included with your machine.
Description Qty
Safety Glasses ........................................... 1
Additional People ....................................... 1
Screwdriver Phillips #2 ............................... 1
Dust Collection System .............................. 1
Dust Hose 2
1
2" ........................................... 1
Hose Clamps 2
1
2" ...................................... 2
Lag Bolts
5
16-18 x 40 (Not Included) .......... 4
Open End Wrench or Socket
1
2................ 1
Drill ............................................................. 1
Drill Bit
1
4................................................... 1
Needed for Setup
Inventory
Box 1: (Figure 3) Qty
A. Drum Sander (not shown) .......................... 1
B. Crank Handle ............................................. 1
C. Dust Port 2
1
2" ............................................. 1
D. Hex Wrench 3mm ....................................... 1
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663
for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
Unpacking
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Figure 3. G0459/G0459P Inventory.
C
B
D
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Wear safety glasses dur-
ing the entire setup pro-
cess!
This machine and its com-
ponents are very heavy.
Get lifting help or use
power lifting equipment
such as a forklift to move
heavy items.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
-14-
Model G0459/G0459P (Mfg. 7/11+)
Site Considerations
Figure 4. Minimum working clearances.
26
1
/
2
"
24"
Weight Load
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Physical Environment
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 2095% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Model G0459/G0459P (Mfg. 7/11+)
-15-
Mounting
The base of this machine has holes that allow
it to be mounted to a workbench. We strongly
recommend that you mount your machine to
a workbench to prevent it from moving during
operation. An unexpected movement could result
in an injury or property damage.
The strongest mounting option is a "Through
Mount" where holes are drilled all the way through
the workbench, and hex bolts, washers, and hex
nuts are used to secure the drum sander to the
workbench.
Machine Base
Workbench
Hex
Bolt
Flat Washer
Flat Washer
Lock Washer
Hex Nut
Figure 5. Example of a through mount setup.
Machine Base
Workbench
Lag Screw
Flat Washer
Figure 6. Example of a direct mount setup.
Another option for mounting is a "Direct Mount"
where the machine is simply secured to the work-
bench with a lag screw.
Installing Crank
Handle
Components and Hardware Needed: Qty
Crank Handle .................................................... 1
The crank handle is installed on the front right
lift screw shaft, and is held in place with two set
screws already threaded into the handle.
To mount the handwheel, place the crank handle
over the shaft shown in Figure 7 and, using a
3mm hex wrench, secure the handle with the two
set screws.
Figure 7. Crank handle installation.
-16-
Model G0459/G0459P (Mfg. 7/11+)
To connect a dust collection hose:
1. Remove the four Phillips head screws at the
dust port hole.
2. Place the 2
1
2" dust port over the top cover
mounting holes and secure with the screws
removed in Step 1 (see Figure 8).
Recommended CFM at Dust Port: 150 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
Dust Collection
DO NOT operate the Model G0459/G0459P
without an adequate dust collection system.
This sander creates substantial amounts of
wood dust while operating. Failure to use a
dust collection system can result in short
and long-term respiratory illness.
Figure 8. Dust port installation.
3. Fit a 2
1
2" dust hose over the dust port and
secure in place with a hose clamp.
4. Tug the hose to make sure it does not come
off. Note: A tight fit is necessary for proper
performance.
Power Connection
After you have completed all previous setup
instructions and circuit requirements, the machine
is ready to be connected to the power supply.
To avoid unexpected startups or property dam-
age, use the following steps whenever connecting
or disconnecting the machine.
Connecting Power
Figure 9. Connecting power.
1. TurnthemachinepowerswitchOFF.
2.
Insert the power cord plug into a
matching
power supply receptacle. The machine
is
nowconnectedtothepowersource.
Disconnecting Power
Figure 10. Disconnecting power.
1. TurnthemachinepowerswitchOFF.
2.
Graspthemoldedplugandpullit
completely
outofthereceptacle.Donotpullbythe
cord
asthismaydamagethewiresinside.
Model G0459/G0459P (Mfg. 7/11+)
-17-
Recommended
Adjustments
For your convenience, the adjustments listed
below have been performed at the factory and
no further setup is required to operate your
machine.
However, because of the many variables involved
with shipping, some of these adjustments may
need to be repeated to ensure optimum results.
Keep this in mind as you start to use your new
drum sander.
Step-by-step instructions for these adjust-
ments can be found in SECTION 7: SERVICE
ADJUSTMENTS.
1. V-Belt Service (Page 30). Perform after the
first 16 hours.
2. Conveyor Tensioning & Tracking (Page 32).
3. Drum Adjustments (Page 33).
4. Pressure Roller Height (Page 35).
Test Run
Once the assembly is complete, test run your
machine to make sure it runs properly.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review the
Troubleshooting on Manual Page 23.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
To test run the machine:
1. Make sure you have read the safety instruc-
tions at the beginning of the manual and that
the machine is setup properly.
2. Make sure all tools and objects used during
setup are cleared away from the machine.
3. Turn the machine ON, then rotate the vari-
able speed knob clockwise to start the con-
veyor belt.
4. Listen to and watch for abnormal noises or
actions. The machine should run smoothly
with little or no vibration or rubbing noises.
Strange or unusual noises should be inves-
tigated and corrected before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
5. Turn the machine OFF.
-18-
Model G0459/G0459P (Mfg. 7/11+)
SECTION 4: OPERATIONS
To complete a typical operation, the operator
does the following:
1. Examines the workpiece to make sure it is
suitable for sanding.
2. Places the workpiece on the conveyor table
under or next to the front pressure roller, and
adjusts the table height until the top surface
of the workpiece just touches the front pres-
sure roller.
3. Checks the outfeed side of the machine to
make sure the workpiece can safely pass all
the way through without interference from
other objects.
4. Wears safety glasses and a respirator.
5. Starts the dust collector.
6. Turns the sander ON, adjusts conveyor
speed, places the workpiece flat on the
conveyor, then lets the conveyor feed the
workpiece into the sander.
7. Slowly raises the conveyor table using the
hand crank until the sandpaper begins sand-
ing the workpiece.
8. Stands at the side of the sander and retrieves
the workpiece from the outfeed end.
9. Stops the machine.
Operation Overview
The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the
machine controls/components
discussed later
in this manual
are easier to understand.
Due to the generic nature of this overview, it is
not
intended to be an instructional guide. To learn
more about specific operations,
read this entire
manual and
seek additional training from expe-
rienced
machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
To reduce risk of eye injury from flying
chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Grizzly G0459 Owner's manual

Category
Power sanders
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI