Hitachi 50SX6P Operating instructions

PROJECTION COLOR TV

OPERATING GUIDE

IMPORTANT SAFEGUARDS

2-5

FIRST TIME USE

6-15

i

D

THE GENIUS REMOTE

CONTROL

EASY GRAPHIC GUIDE

16-29

30 - 48

USEFUL INFORMATION

INDEX

49-55

IMPORTANT

Follow all warnings and instructions marked on this television receiver.

CAUTION

A

RISK OF ELECTRIC SHOCK AL

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, isintended to alert the user to the

presence of uninsulated "dangerous voltage" within

the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamationpointwithinanequilateraltriangleis

intendedtoalerttheusertothepresenceofimportant

operatingandmaintenance(servicing)instructionsin

the literatureaccompanyingthe appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS TELEVISION SYSTEM TO RAIN OR MOISTURE.

I

I NOTE:

• There are no user serviceable parts inside the receiver.

• Model number and serial number are indicated on back side of the set.

I

POWER SOURCE:

This projection color TV Is designed to operate on 120 volts 60 Hz, AC household current.

Insert power cord Into a 120 volt 60 Hz outlet.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION'S PLUG WITH AN EXTENSION CORD,

RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY

INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE TV TO 50 Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED

VOLTAGE.

I NOTE: This television receiver willdisplaytelevision closed captioning, (rc'_orE;]), inaccordance with paragraph I

I

15.119 of the FCC rules.

I

/_CAUTION:

Neverremovethebackcoverofthesetas thiscanexposeyoutoveryhighvoltagesandother

hazards.Ifthesetdoesnotoperateproperly,unplugthesetandcallyourdealerorserviceshop.

HITACHI's60SX8B,60SX9Kand50SX6P employstate-of-the-artcomputer circuitstoenhance

pictureperformance.ShouldyourprojectionTV becomeunpluggedfromtheAC walloutletor

loseACpowerduetoa localpowerfailure, pleasewaitat least30 secondsfollowing returnof

powerbeforeturningonyourTV. Thiswillallowthecomputerstimetocheck/correctanyinternal

errorscausedbythe lossof power.

SAFETY TIPS

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI TELEVISION RECEIVER

IMPORTANT SAFEGUARDS

CAUTION:

* Read all of these instructions

* Save these instructions for later use,

* Follow all warnings and instructions marked

on the television receiver.

Our reputation has been built on the quality, pedormance, and ease of service of HITACHI television receivers.

Safety is also foremost in our minds n the des gn of these un Is To help you operate these products propedy, this folder illustrates safety tips which will be of benefit

to you, Please read it carefully and apply the knowladge you obtain from it to the proper operation of your H TACH te ev s on receiver,

Please fill out your warranty card at once and mail It to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should

be discovered in your model of product.

FOR YOUR PERSONAL SAFETY 7

This television set is equipped with a polarized

alternating-current line plug (a plug having one

blade wider than the other). This plug will fit into the

puwer outlet only one way. This is a safely feeture.

If you am unable to insert the plug fully into the

outlet, try reversing the plug. If the plug should still

fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat _ safety purpose

of the polarized plug.

2 When the power cord or plug is damaged or

frayed, unplug this television set from the wall

outlet and refer sarvicleg to qualified service per-

sonnol.

3 Do not overload wall outlets and extension cords

as this can result in fire or electric shock.

Do not allow anything to rest on or roll over the

pewer cord, and do on( placa the TV where the

powercordis subjectto Irafficor abuse. This rcay

result in a shock or fire hazard.

Do not attempt to service this television set your-

self as ode_ng or removing covers may axpcoe

you to clangorous voltage or other hazards, Refer

ell sarvicing to qualified service pe_l.

Never push objects of any kind into this tekP,=",=ion

sat through cabinot sfots as fr"ley may touch dan-

gerous vet!age points or short out parts thet could

result in a fire or electric shock. Never spill liquid of

any kind on the television set.

_9

11-1

If the television set has been dropped or the

cabinet has been damaged, unplug this television

set from the wall outlet and refer servicing to

qualified sarvica personnel.

If liquid has been spilled into this television set,

unplug it from the wall outlet and refer service to

qualified service personnel.

DO not subject your television set to impact of any

kind. Be particularly careful not to damage the

picture tube sudace.

Unplug this television set from the wall outlet

before cieaning. DO not use liquid cleaners or

aerosol cleaners. Usa a damp cloth for cleaning.

Do not place this tolavision set on an u_ cart,

stand, or table. The television sat may fall, causing

serious injury to a child or an adult, and serious

damage to the appliance. Use only with a cart or

stand recommended by the manufacturer, or sold

with the television saL Wall or shelf mounting

should fullow the manufacturer's instructions, and

should use a mounting kit approved by the manu-

facturer.

An appliance and cad combinationshould be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

appliance and cart combination to overturn.

I

PROTECTION AND LOCATION OF YOUR SET

12 Do no( use this television set near water, for

example,neara bathtub,washbowl,kitchensink.

or laundry tub. in a wet basement, or near a

swimming pool,etc.

Never expose the set to rein orwater. Ifthe set has

been exposed to rain or water, unplug the sat from

the wall outlet and refer to servicing personnel.

13 Choose a place where light (arlfficlel or sunlight)

does not shine directly on the screen.

14 Avoid dusty places, since accumulated dust in-

side the chassis may cause failure of the set when

high humidity persists.

":.

15

The set has elots, or openings in the cabinet for

ventilation I_rpoees, to provide reliable operation

of _ receiver, and to protect from overheating.

These openings must not be blocked or covered.

Never cover the slots or openings with cloth or

other material.

Never block the bottom ventilation slots of the set

by placing it on a bed. sofa, rug, etc.

Never place the set near or over a radiator or heat

register.

Never place the set ina "built-in" enclosure, unless

proper ventilation is providedl

*.O°D'_'

3

SAFETY TIPS

PROTECTION AND LOCATION OF YOUR SET

16-1 Ifan outside antenna is connected to the television

set, be sure the antenna system is grounded so as

to provide some protestion against voltage surges

and built up static charges. Section 810 of the

National Electrical Code, NFPA No. 70-1975, pro-

_c t_T_ P_m_q

IKIECMTIOK_ELECl_CAL¢00E

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE INSTRUCTIONS

16-2

17

18

vibes information with respect to groper grounding

of the mast end supporting structure, grounding of

the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna dis-

charge unit, connection to grounding electrode,

end requirements for the grounding electrode.

Note to CATV system installer:

(Only for the leisvision set with CATV reception)

This mminber is provided to call the CATV system

in,stalk}Ks attention to Article 820-40 of the NEC

that provides guidelines tor proper grounding and,

in particular, specifies that the cable ground shall

be connected to the grounding system of the

building, as close to the point of nabla entry as

practical.

An outside antenna system should not be located

in the vicinity of overhead power lines or other

electrical lights or power circuits, or where it can

fall into such power lines orcircuits. When install-

ing an outside antenna system, extreme care

should be taken to keep from touching such power

lines or cirouits as contact with them might be fatal.

For added protection for this television set during

• lightning storm, or when it is left unattended end

unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna. This will

prevent damage due to lightning and power-line

surges.

OPERATION OF YOUR SET

19

This talevision set should be operated only from

tba type of power sourne indicatod on ttm marking

label. If you are not sure of Me type of power

supply at your home, consult your tolevielon deeler

or local power company. For television sets

designed to operate from battery power, refer to

the operating instruc'_ns.

2O

21

If the television set does not operate normally by

following the operating instructions, unplug this

television set from the wall outlet and refer servic-

ing to qualified service personnel. Adjust only

those controls that are covered in the operating

insthJCtions as improper adjustment of other con-

tmls may result in damage and wilt often require

extensive work by a qualified technician to restore

the television sot to normal operation.

When going on a holiday: If your television set is

to remain unused for • period of time, turn the

television set "off' and unplug it from the wall

outlet.

IF THE SET DOES NOT OPERATE PROPERLY

22

If you are unable to r_tore nom_l operatioql by

foliowing the detailed procedure in your operating

instructions, do not attempt any further adjust-

merit. Unplug the set and call your dealer or

senrioe technician.

23

24

Wbanever ttte felevision ,=etis damaged or fails, or

a distinct change in performanne indicates e need

for service, unplug the set and have it ctNK:ked by

a professional service technician.

Itis normal for seine TV eets to make ocoasional

snapping or polming sounds, particularly when

being turned on or off. If the seapping or geppmg

is continuous or frequent, unplug the set and

soneuit your dealer or service technician.

FOR SERVICING AND MODIFICATION

25 Do not use attachments net renommonded by the

television set manufacturer as they may cause

hazards.

26

When replacement paris am required, be sure the

service technician has used replacame_ parts

specified by the manufacturer that have the came

characteristi_ as the original part. Unauthorized

substitutions may result in tire, electric shock, or

other hazards.

27

Upon completion of any sen_ne or repairs to the

televP_on set, ask the service technician to per-

Ion'n routine safety checks Io determine that the

television is in safe operating condition.

osk

4

PICTURE CAUTIONS

WARNING

Continuous on-screen displays such as

video games, stock market quotations,

computer generated graphics, and other

fixed (non-moving) patterns can cause per-

manent damage to projection television

receivers. Such "PATTERN BURNS" con-

stitute misuse and are NOT COVERED by

your Hitachi Factory Warranty.

When using the Picture-in-Picture function, the sub-picture should not be left permanently

in one corner of the screen or a "pattern burn" may develop over a long period of time.

This projection television receiver was intended mainly for the private viewing of programs

broadcast by TV stations and cable companies and programs from other video sources.

Public viewing may require prior authorization from the broadcaster or owner of the video

program.

(_'_ ACCESSORIES

Check to make sure you have the following accessories before disposing of the packing material

A

, ,= ,_ ,,

OO_,-

<DOO

i

w

1.

.

1. GeniusRemoteControlUnitCLU-850GR (PartNo.2573971).

2. Four =AA"size (SUM-3), 1.5V batteries(For RemoteControlUnit).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1.

.

Open the battery cover of the remote transmitter by

pushing the notched part of the cover with your

fingers.

Insert four new =hA" size (SUM-3) batteriesor

equivalentfortheGeniusRemote. Whenreplacing

oldbatteries,pushthemtowardsthespringsand lift

themout.

Match the (+) and (-) marks in the battery compart-

ment.

4. Replace the cover.

J

BOTTOM

HOW TO SET UP YOUR NEW HITACHI PROJECTION TV

ANTENNA

Unless your TV isconnected to a cable "IV system or toa centralized antenna system, a good outdoor color TV antenna

is recommended forthe best performance. However, if you are located in an exceptionally good signal area that is free

from interference and multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Selectanarea wheresunlightorbrightindoorilluminationwillnotfalldirectlyon thepicturescreen. Also,be surethat

thelocationselectedallowsa freeflow ofair toandfromtheperforatedbackcoveroftheset.

To avoidcabinetwarping,cabinetcolor changes,and increasedchance of set failure,do not place the TV where

temperaturescan becomeexcessivelyhot. Forexample,in directsunlightor neara heatingappliance,etc.

VIEWING

The majorbenefitoftheHITACHIProjectionTelevisionis

itslargeviewingscreen. To see thislargescreenat its

best,testvariouslocationsintheroomtofindthebestspot

for viewing.The drawingsgive severalsuggestions.

Thebestpictureisseenbysittingdirectlyinfrontofthe'IV

and about10 to 18 feet from the screen. Picturebright-

nessdecreasesastheviewermovestotheleftorrightof

thereceiver.

Duringdaylighthours,reflectionsfromoutsidelightmay

appearon the screen. Ifso, drapesor screens can be

usedtoreducethe reflectionortheTV can belocatedin

a differentsectionofthe room.

If the TV's audio outputwill be connectedto a Hi-Fi

system'sexternalspeakers,thebest audioperformance

willbe obtainedbyplacingthe speakersequidistantfrom

eachsideofthereceivercabinetandascloseas possible

totheheightofthepicturescreencenter. Forbest stereo

separation,place the externalspeakersat least 4 feet

from thesideoftheTV. Placethesurroundspeakersto

thesideor behindthe viewingarea. Differencesin room

sizesand acoustical environmentswillrequiresomeex-

perimentationwith speaker placementfor best perfor-

mance.

4' MINIMUM

i

15'

4'MINIMUM

I _CAUTION:

The magnetic field of extemal speakers may cause the TV picture to distort if the speakers are

placed too close to the television. Move the speakers away from the TV untilthere is no picture

distortion.

7

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can

be made with shielded video and audio cables that have

phono connectors. For best performance, video cables

should use75-ohm coaxial shielded wire. Cables can be

purchased from most stores that sell audio/video prod-

ucts. Below are illustrations and names of common con-

nectors.

Before purchasing any cables, be sure of the output and

input connector types required by the various compo-

nents. Also make sure the cables are the correct length.

300-Ohm Twin Lead Connector

This outdoorantenna cable must be connectedto an

antennaadaptor(300-Ohmto 75-Ohm).

"F" Type 75-Ohm Coaxial Antenna Connector

ForconnectingRF signals(antennaor cable"I-V)to the

antennajackon thetelevision.

@

Phono Connector

Used onall standardvideoand audio cableswhichcon-

necttoinputsandoutputslocatedontheTelevision'sfront

and rearjackpanels.

S-Video (Super Video) Connector

This connectorisusedoncamcorders,VCR's, andlaser

disc players with an S-Video feature in place of the

standardvideocableto producea high-qualitypicture.

ANTENNA CONNECTIONS TO REAR JACK PANEL

REAR OF'IV

VHF (75-Ohm) antenna/CATV(cable TV)

When usinga 75-Ohmcoaxialcablesystem,connectthe

outdoorantennaorCATV coaxialcable totheVHF/UHF

75 Ohmterminal.Ifyouhavea secondantennaorcable

TVsystem,connectthecoaxial cabletotheAUXterminal.

VHF (300-Ohm) antenna/UHF antenna

When usinga 300-Ohm twin lead from an outdooran-

tenna,connecttheVHF orUHF antennaleadstoscrews

of the VHF or UHF adaptor. Plugthe adaptorintothe

antennaterminalontheTV.

When both VHF and UHFantennas are connected

Attachanoptionalantennacable mixertotheTVantenna

terminal,and connectthe cablesto the antenna mixer.

Consultyourdealerorservicestorefortheantennamixer.

To outdoorantenna

orCAI"V_ble_

To outdoorVHF

or UHF antenna

To outdoor

To UHF VHF/UHF antenna or

Antenna O CATV systerr

Antenna mixer

FRONT PANEL CONTROLS

pu_fo_ard and down

/

(9

AVX (AudioNideo) selector

Press this button to select the current antenna

source,orVIDEO: 1,2, or3. Yourselectionisshown

inthetop rightcomerofthe screen.

@ VOLUME level

Press these buttons for your desired sound level.

The volume levelwill bedisplayed on the TV screen.

FRONT PANEL CONTROLS

O CHANNEL selector

PressthesebuttonsuntilthedesiredchannelappearsinthetoprightcorneroftheTV screen.

(_ POWERbutton

PressthisbuttontoturntheTV on or off.

Q POWER light

You will see a red light when the "IV istumed on.

NOTE: YourHITACHITVwillappeartobetumed"off'ifthereisnovideoinputwhenVIDEO:1,2, or3 isselected.

CheckthePowerOn indicatorto makesuretheTV isoffwhennotin use.

(_ AI (Artificial Intelligence) sensor

This=ArtificialIntelligence"sensorwillmakeautomaticpictureadjustmentsdependingontheamountoflightinthe

roomto givethebestpicture. (See page 43.)

(_) REMOTECONTROL sensor

PointyourGeniusRemoteat thisareawhenselectingchannels,adjustingvolume,etc.

(_ V-SYNC (Vertical Hold) knob

If the TV picture"rolls=up or down,adjustthis knobuntilyou get a good picture.Thiscontrolseldomneeds

adjustment.

O FRONT INPUT JACKS (for VIDEO: 3)

Use these audio/video jacks for a =quick"hook-up from a camcorder or VCR to instantlyview your favorite show or

new recording. (Press the AVX button until VIDEO: 3 appears inthe top right comer of the TV screen,)

10

FRONT PANEL JACKS AND CONNECTIONS

The front panel jacks are provided as aconvenience to allow you to easily connect a camcorder or VCR as shown in the

following examples:

S-VHS Video camera

Videocamera

0

OUTPUT

Insertaudiocable

intoleftchannel

formonosound

INPUT

VIDEO:3 _1

o 0000

S-V1DEO V L R

c=

_=

O

OUTPUT

INPUT

I

y jo .oEo 3

;I o @ooo

S-VIDEO V L R

NOTE: Completely insert the connection cord plugs when connecting to front panel jacks. Ifyou do not, the played

back picture may be abnormal. Ifyou have an S-VHS VCR, use the S-INPUT cable inplace ofthe standard

video cable.

11

REAR PANEL JACKS

r

O

r...................................

VHF/UHF

TO CONVERTER=

AUX

()

L

REAR SPEAKER

8_ ONLY

@

I

olloll

IDIO

HIFI

,)

F-

o_

®

(D

®

Antenna Inputs/Output

The =ANT"buttonontheGeniusRemoteControlallowsyouto switchbetweentwo separate75-ohm RF antenna

inputs,Main(VHF/UHF)andAuxiliary(AUX).The antennaoutputlabeled=Toconverter"allowstheMain(VHF/UHF)

antennaconnectionto passdirectlyto a differentsourcesuchas a pay-TVcabledecoder.

Audio/Video Inputs 1, 2

The "AVX"(Auxiliaryvideo)buttonwillstepthrougheachvideosourceand thecurrentantennainputeachtimeit

is pressed.Use theaudioand videoinputstoconnectexternaldevices,suchas VCR's, camcorders, laserdisc

players,videogames,etc.

Output

Thesejacksprovidefixed audioand videosignalswhichare usedfor recording.

Audio to HI-Fi

These jacksprovidevariableaudiooutputtoa separatestereosystemamplifier.Withthis connection,theaudioto

thestereocanbecontrolledbythetelevision'sremotecontrel.Usethesejacksforthe SURROUND LeftandRight

channels(See page 15).

Rear Speaker Terminals

Theseterminalsareusedtoconnectextemalspeakers,whichare usedforthesurroundsoundfeature.The volume

leveliscontrolledbythe remotecontrolmainvolumebuttonsandalsobyanindependentrearvolumefeature found

in the=sound"function menu.Use speakerswith8 Ohmimpedanceonly.

S-Video

Input 1provides S-Video (Super Video) jacks for connecting equipment with S-Video output capability.

12

REAR PANEL CONNECTIONS

._ Outside antenna or

cable TV coaxial cable

_ _------2-way signal splitter

[/_:_, _ Optional, see tips

on page 14

Cable TV box \1/

v

[____o,O<___'N_'"I r--"_

;° vcR,2

See connections

on page 14

/

0

iO

0

StereoSystemAmplifier

Typical full feature set-up. Followconnectionsthatpertai'ntoyourpersonalentertainmentsystem.

13

REAR SPEAKER TERMINAL CONNECTIONS

Connect after turning the power to the TV OFF.

Press the Right Speaker red button and insertthe positive(+) lead wire intothe hole below the button. When The button

is released, the wire islocked intoplace. In the same manner, press the Right Speaker black buttonand insertthe negative

(-) lead wire. Repeat this procedure for the Left Speaker.

TO

EXTERNAL<_

SPEAKER

/_CAUTION:

DonotconnectSpeakerssimultaneouslytotheREAR SPEAKERterminal of theProjectionTV

and an extemalamplifier.Thiscoulddamage boththe"IV and the speakers. Your TV was

designedto use8 Ohmspeakersonly.Anyothertypemaydegradetheaudioperformanceof

yourentertainmentsystem.

PROJECTIONTV SPEAKER AMPLIFIER

TIPS ON REAR PANEL CONNECTIONS

The S-Video connectionis providedfor high performancelaser discs,VCR's, etc., that have this feature.Use this

connectionin placeofthe standardvideoconnection ifyourdevicehasthisfeature.

Ifyourdevicehasonlyone audiooutput(monosound),connectittothe leftaudiojack ontheTV.

Referto theoperatingguideofyourotherelectronicequipmentfor additionalinformationon connectingyourhook-up

cables.

A singleVCR can be used for VCR #1 and VCR #2, but notethata VCR cannot record itsownvideoor lineoutput

(INPUT: 1 in the example on p. 13). Refer to yourVCR operatingguide for more informationon =line"input-output

connections.

14

AUDIO SYSTEM SET-UP

, :•..

Match the numbers below to the diagram for speaker placement and refer to the table for the different surround sound

requirements. (See page 47 for SURROUND functions.)

The television'sintemalspeakers.

These speakersareconnectedtoa separateaudioamplifier.Usethe"AudiotoHi-Fi"outputonthe TV.

O These speakersareconnectedtotheRear Speaker8 Ohmoutputon theTV.

SURROUND

FEATURE

OFF

HALL

MATRIX

DOLBY 3CH

DOLBY PRO-LOGIC

(PHANTOM)

DOLBY PRO-LOGIC

(NORMAL)

REQUIRED

CONNECTION

®

@®

EFFECT

ReceiveMonoand StereoSound.

OP_ONAL

CONNEXION

®®

®

ConcertHallSound.

Feeling of being at a Stadium.

@® ®

15

O®®

Movie Theater Reproduction, Surround Channel

added to left and right audio amplifier speakers.

Movie Theater Reproduction, center channel

added to "IV left and right speakers.

Movie Theater Reproduction with separate left,

center, right, and surround channels to improve

sound clarity and spatial positioning.

j

THE GENIUS REMOTE CONTROL (CLU-850GR)

Inadditiontocontrolling allthefunctions onyour HITACHI

ProjectionTV, the new GeniusRemote is designedto

operatedifferenttypesof VCR's and differenttypesof

CATV(CableTV) converterswithonetouch.Basicopera-

tionkeys are groupedtogether in one area. All other

controlsareseparatedfrom themandarrangedin MULTI-

PAGE sections, with a display that can be switched to

cover any of the four pages. Functions are arranged and

properly categorized into windows, making operation

simple when multiple functions are to be controlled.

To operateyour TV, point the GeniusRemote at the remote sensorofthe TV.

To operateyour VCR, pointtheremoteat the remotesensoroftheVCR.

o

READY LEARN

POWER

t ................................. °°_,

!1P.P I IExc._l I ='_1 I._EEI!

t1 ii ii ii II

.....mP.:::::...............................

CURSOR

CHANNEL VOLUME

Q®

®®i

®

100

®o

Q

(i)

AVX

©

H rr_H I

GENIUS REMOTE

CLU-850GR

Q

O READY indicator light

Referto Page26.

Q SEND/LEARN indicator light

Refer to page 26.

Q LEARN/USE select switch

(Locatedon rearside ofremotecontrol)

LEARN........ EnterstheLearningmode.

(Refertopage 26)

USE............ Set for normaluse.

Q MULTI-PAGE select switch

This selects the button layout of the multi-page

section of the remote control.

O ULTI-PAGE buttons

These buttonschange functions as shown on page

17.

(_),Q LIGHT button

Whenyou are in a dark room,press thisbutton on

thesideoftheremotetolightupthebuttonsshown

in (_. The lightwillstayonfor about8 secondsif

nobuttonispressed.The buttonswillnotappearto

lightifthe roomistoobright.

16

MULTI-PAGE WINDOWS

_-.

POWER READY LEARN

I _ I I tl I IRECALq!

CURSOR

SELECT

SWITCH

POWER RF_DY LEARN

!lTvmNI II II 0 I1

!1<4 II _" II _'_'11 0 I1

Itll SELECT !

CURSOR

MENU

_e

SELECT

SWITCH

When"TV"isset

When"VCR"isset

POWER READY LEARN

!1 II II I ISEI-EC_I

c_

.o

_wO

'_0

SELECT

SWITCH

POWER READY LEARN

[ A II a II c II o i

I E II F II G II " IJ

I ' II " II K II L Ii

I_I..,.,,.'r,,,_

SELECT

SWITCH

When"CATV"isset When"USER"isset

17

HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV

©

®

POWER button

Pressthisbuttontotumthe'IV setonoroff. Ifan

automaticmessageisset,itwillbedisplayedwhen

the TV isfirst turnedon. (See page 41.)

RECALL button

When you want to check the channel being re-

ceived, or if it has a stereo (ST) or second audio

program (SAP), press the RECALL button.

Youcanalsocheckthetime, and iftheONTIME

orOFF TIME hasbeen set.(See page40,)

Ifa videoinputis used:

VkteoInput

,/

VIOEO:l _. WhenanS-V'_eo

(S-IN) _.

inputisconnected

®

You can also use the RECALL button to quickly clear

many of the other on-screen displays.

©

POWER

READY LEARN

II II I!

I

O

HITACHI

GENIUS REMOTE

CLU-850GR

18

HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV

j

(_) ANT button

Use the ANT (Antenna) button to select between the VHF/UHF and AUX (Auxiliary) antenna inputs.

I NOTE: When VHF/UHF isselected, the channel number inthe upper right comer of the screen isin green. When

I

the AUX input is selected, the channel number is in yellow.

I

(_ ENTER, CURSOR buttons

MENU,

All the on-screen display features can be set or adjusted by using these buttons.

The =MENU" button will start or exit the on-screen display.

The "CURSOR"buttonswillhighlightfunctionsoradjustdifferentfeatures.

These buttonsarealso usedfor FAVORITE CHANNELS. (see Page35)

®

I

®

The =ENTER" button will set features to your preference.

"CHANNEL SELECTOR" buttons are used to set the time, for channel memory, etc..

CHANNEL SELECTOR buttons

Entertwo orthree numbers to select channels. Enter a=0"firstforchannels I to9. Use the "100 _button forchannels

100 and higher.

Channel selection may also be performed by pressing channel up ( • ) or down ( • ).

NOTE: The TV may not receive some channels if you are not in the correct AIR/CABLE mode. See page 32. I

I

AVX button

The AVX (Auxiliary Video) button will select between the antenna signal and the three sets ofvideo inputjacks each

time the button ispressed. If the Picture-in-Picture (PinP) ison, the AVX will select between the three sets ofvideo

input jacks. (See page 21)

ESPN STEREO 28

STISA

AVX

T I

AVX AVX

O O

VIDEO:3

AVX

O

VIOEO:I

(S-IN)

VIDEO:2

19

__ HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV

VOLUME, MUTE buttons

Press the "VOLUME" up ( • ) or down (• ) button until you obtain the desired sound level.

To turnthe sound offinstantly toanswer thetelephone, etc., ptess the "MUTE" button. Pressthe "MUTE" button again

or press the "VOLUME" up ( • ) button to restore the sound.

MTV STEREO 28

VOLUME

IIIIIIIIIIIIIIIIIIIIIIIIIIIIII""""""""'"""

f

Louder

The word "MUTE" will remain displayed if the CLOSED CAPTION feature is turned off.

The word "MUTE" will not be displayed if the CLOSED CAPTION feature is on.

(_ LAST CHANNEL (LST-CH) button

Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)

PRME STEREO 28

L_ STISA

;TEREO

PICTURE-IN-PICTURE buttons

See separate section on page 21 for a description.

2O

Page is loading ...

Hitachi 50SX6P, 46UX16B, 46UX17K, 46UX17KAP43, 50UX18B, 50UX19K, 50UX19KAP43, 60SX8B, 60SX9K, 60SX9KAP43B Operating instructions

Related papers

Other documents