Zenith SRV1341W Operating Manual & Warranty

Brand: Zenith

Model: SRV1341W

Category: CRT TVs

Type: Operating Manual & Warranty

This manual is also suitable for

SRV1341

Operating Guide

& Warranty

13" Color TV/VCR Combination

SRV1341W

WARNING:

TO REDUCE THE P,151x_t- HI<E OR t'A.ECIRIt2 5HOtgK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

_CAUTION: TO REDUCE THE RISK OF ELECTRIC-

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERV-

ICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE

APPLIANCE.

The caution marking is located on the rear of the cabinet.

IMPORTANT SAFEGUARDS

1.Read instructions-All the safety and operating instruc-

tions should be readbefore the appliance is operated.

2.Retain Instructions-The safety andoperating instructions

should be retained for future reference.

3.1teed Warnings-All warnings on the appliance and in the

operating instructions should be adhered to.

4.Follow Instructions-All operating and use instructions

should be followed.

5.Cleaning-Unplug TVNCR' from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

EXCEPTION : A product that is meant for uninterrupted

service and, that for some specific reason, such as the

possibility of the loss of an authorization code for a CATV

converter, is not intended to be unplugged by the user for

cleaning or any other purpose, may exclude the reference

to unplugging the appliance in the cleaning description

otherwise required in item 5.

6.Attachments-Do not use attachments noi recommended

by the TV/VCR manufacturer as they may cause hazards.

7.Water and Moisture-Do not use this TV/VCR nearwater-

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub, in a wet basement, ornear a swimming pool,

and the like.

8.Accessories-Do not place this TV/VCR on an unstable

cart, stand, tripod, bracket, or table. The TV/VCR may fall,

causing serious injury to someone, and serious damage to

the appliance. Use only with a cart, stand, tripod, bracket,

or table recommended by the

manufacturer, or sold with the

TV/VCR. Any mounting of the PORTABLE_CARTWARNING

appliance should follow the ,__

manufacturer's instructions and

should use a mounting accessory

recommended by the manufac-

turer. An appliance and cart com-

bination should be moved with

care.

Quick stops, excessive force, and uneven surfaces may

cause the appliance and carl combination to overturn.

9.Ventilation-Slots and Openings in the cabinet and the back

or bottom are provided for ventilation and to ensure reliable

operation of the TV/VCR and to protect it from overheat-

ing, these openings must not be blocked or covered. The

openings should never be blocked by placing the TV/VCR

on a bed, sofa, rug, or other similar surface. This TV/VCR

:.should never be placed near or over a radiator or heat

installation such as a bookcase or rack unless proper ven-

tilation is provided or the manufacturer's instructions have

been adhered to.

10.Power Sources-This TVNCR should be operated only

from the type of power source indi,cated on the marking

label. If you are not sure of the type of power supply to

your home, consult your appliance dealer or local power

company. For TV/VCRs intended to operate from battery

power, or other sources, referto the operating instructions.

ll,Grounding or Polarization-This TV/VCR is equipped

with a polarized alternating-currentline plug(a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. Ifthe plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be

routed so thatthey arenot likely tobe walked on orpinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and

the point where they exit from the appliance.

- 2 - EN

5L01

FIGURE. A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

TENNA

LEAD IN

WIRE

. ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

'NEC - NATIbNAL ELECTRICALCODE

$2898A

13.Outdoor Antenna gi_0Undlng-lf an ' _' ' antenna

outside or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-dis-

charge unit, connection to grounding electrodes, and re-

quirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TVNCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TVNCR due to lightning and

power-line surges.

15.Power Lines-An outside antenna system Should not be

located in the vicinity of overhead power lines or other

', electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touch-

ing such power lines or circuits as contact with them might

be fatal.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TVNCR through openings as they may touch

dangerous voltage points or shortout partsthat could result

in a fire or electric shock. Never spill liquid of any kindon

the TVNCR.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening orremoving covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

GROUNDING COND'U(_T_)R_

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVI _E GROUNDING

.---'-._1-"-" ELECTRODE SYSTEM

(NEC ART 250. PART H)

19.Damage Requiring Service-Unplug this TVNCR from

the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TVNCR to its normal operation.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perform-

ance-this indicates aneed for service.

20.Replacement Parts-When replacement parts arerequired,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same charac-

teristics as the original part. Unauthorized substitutions

may result in fire, electric shock, injury to persons orother

hazards.

21.Safety Check-Upon completion of any service or repairs

to this TV/VCR, ask the service technician to perform

routine safety checks to determine that the TV/VCR is in

: proper operating condition.

22,Heat-This TVNCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

For safe operation and satisfactory performance of your

unit, keep the following in mind when selecting a place •

for its installation: •

• Shield it from direct sunlight and keep it away from

sources of intense heat.

• Avoid dusty or humid places.

• Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventilation

holes.

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting it

from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to an

authorized Sears service center for servicing.

Do not put your fingers or objects into the TV/VCR

cassette holder.

Do not place anything directly on top of the unit.

• Install unit in a horizontal position.

• Avoid locations subject to strong vibration.

• Do not place the unit near strong magnetic fields.

• Do not move the unit from a cold to a hot place or

vice versa.

Moisture condensation may occur inside the unit when

it is moved from a cold place to a warm place, or after

heating a cold room or under conditions of high humid-

ity. If a tape is played in a TV/VCR which has moisture,

it may damage the tape and TV/VCR. Therefore when

the condensation occurs inside the unit turn the POWER

button on and allow at least 2 hours for the unit to dry

out.

ill !,!l ! _tj!l i !llll!ll_lli ._" "_'7 ............. ..... _"

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications

to this equipment may cause harmful interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized change

or modification is made.

i i1 ul i ,m i ill d " f, r" . Jl ill ] , I , 11

i , ,,, i i )

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast television programming, video tape, film or othei_copyrighted

material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication,

use, or other acts which infringe upon the rights of copyright owners. : 1

i ii j i i i

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-

nications.

However, there is no guarantee that interference'will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver. " "........

3) Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

-4-

6F06

1AiiL, I:t, t)i_ CON _i E,["_I

llMPORTANTSAFEGUARDS ............................ 2 GAME MODE .................................................... 19

• PRECAUTIONS ................................................... 4

PICTURE CONTROL ........................................ 19

CLOSED CAPTION SYSTEM 20

• TABLE OF CONTENTS ...................................... 5

• NORMAL PLAYBACK .......................... ......,._.'.. 21

• FEATURES .......................................................... 6 • SPECIAL PLAYBACK ................................... i... 22

• SUPPLIED ACCESSORIES ............................... 7 RENTAL PLAYBACK ...................................... 22

• OPERATING CONTROLS AND FUNCTIONS.. 8

• PREPARATION FOR USE ............................... 10

CABLE CONNECTIONS .................................. 10

EXTERNAL INPUT MODE ............................. . 12

INSTALLING THE BATTERIES .......i............. 12

INSTALLING MAGNET ON THE REMOTE

CONTROL .......................................................... 12

USING THE SWIVEL ...................................... . 12

• VIDEO CASSETTE ............... ,...,;. .......... ,....:,.. 13

1PRESET FOR USE ............................................ 14

PRESET FOR THE FIRST TIME ..................... 14

REPEAT PLAYBACK ........................................ 22

• SEARCH ......................... .................. ......_,.......... 23

COUNTER MEMORY ...................................... 23

TIME SEARCH ................................... 23

INDEX SEARCH .......... ;.................................... 24

• RECORDING .............. ';...................... ................ 25

NORMAL RECORDING ................................... 25

SKIPPING SOME MATERIALS DURING

RECORDING ..................................................... 25

OTR (One Touch Recording) ............................. 26

COPYING A VIDEO CASSETTE

(Requires another VCR) ............................... ...... 26

DELETING (OR ADDING) PRESET

CHANNELS ..................................................... ;. 14

AUTO PRESET AGAIN ............ ........................ 15

SELECTING DESIRED LANGUAGE ..........:. 15

DAYLIGHT-SAVING TIME ................... _........ 15

SETTING THE CLOCK (AUTO / MANUAL). 16

• ON-SCREEN DISPLAY ................................ .,d_18

TIMER ............. ......... ..................: ...................... 27

AUTOMATIC TIMER RECORDING .............. 27

AUTO RETURN ................................................ 29

SLEEP TIMER ................................................... 30

ALARM TIMER ................................................ 30

• TROUBLESHOOTING GUIDE .......... ..,..... ,_.. 31

• MAINTENANCE ............................................... 33

• SPECIAL FEATURES ...................................... 18

DEGAUSSING ................................................... 18 • SPECIFICATIONS ............................................ 34

AUTO REWIND-EJECT .................................... 18

• SERVICE ............................................................ 35

• TVOPERATION ................................................ 19

• WARRANTY ....................................................... 36

WATCHING A TV PROGRAM ....................... 19

The serial number of this product is on the back of the unit. Each serial number is unique. You should record

this number and other vital information in this book and keep as a permanent record of your purchase in

the event of theft to aid in its identification.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 5 - EN

6F06

• Rotary 4-head Record/Playback System-Rotary

4-heads ensure excellent picture quality and special

effects playback.

• Infrared remote control

• Swivel-Allows you to rotate the TV/VCR easily in

any direction.

• Magnet-By installing the magnet onto the back of

the remote, you can stick the remote onto any metal

surface, such as a refrigerator door.

• Bilingual on-screen menu display selectable In

English or Spanish

• Real time counter-This shows the elapsed record-

ing or playback time in hours, minutes, and seconds.

The "-" indicates that the tape is rewound further

than "0:00:00" on the tape counter.

• 181 channel capability PLL frequency synthesizer

tuner with direct station call- (A converter may be

necessary to view scrambled cable channels.)

• Auto clock setting-Allows you to use the clock

function from the PBS broadcast.

• Closed caption system-You may view specially

labeled (cc) TV programs, news, prerecorded tapes,

movies, etc. with either a dialogue caption or text

display added to the program.

• Game mode- Makes the video display more

suitable for use with TV games.

• Auto power on system- (when a tape is inserted)

• Auto rewind when the end of a tape Is reached-

(not in the case of timer recording).

• 2 Step picture search operation- You can view

a video program at a high speed or super high speed

in either a forward or reverse direction in either LP

or SLP mode.

• Still-You can "freeze" the picture at any time to

inspect a particular scene. Only tapes recorded in the

SLP mode will show a fairly clear picture.

• Slow Motion- You can view the video program at a

slower than normal playback speed. Slow speed can

be controlled by pressing F.PNVD button (faster) or

REWIND button (slower).

• Digital Auto Tracking (DTR)-Adjusts the tracking

automatically for each tape you play.

• Rental play mode-improves playback picture

quality of worn tapes, such as rental tapes.

• Auto repeat-Allows you to repeat a tape indefinitely

without pressing the PLAY button.

e Time search- Allows you to set tlie TV/VCR to

advance the tape by entering the desired playback

time you want to skip.

• Three different tape speeds : SP/LP/SLP

• OTR (One Touch Recording)- By pushing REC/

OTR button, instant timed recording from 30 to 480

minutes is possible.

• 1 Year, 8 events (Including Dally and Weekly

Timer Recordlng)-The built-in timer allows you to

record up to 8 programs at different times on different

channels up to 1 year in advance. The Daily timer

allows recordings to be made of daily broadcasts.

The Weekly timer allows recording to be made once

a week until to the end of the tape is reached.

• Auto return-The beginning of the recorded

program(s) can be searched after timer recording

finishes.

• Sleep timer-Allows you to have the TV/VCR

turn off automatically at a desired time.

• Alarm timer-Allows you to have the TV/VCR

turn on automatically at a desired time.

i '! ,i

-6- EN

6F06

3 UVI LILD A_UI_UKIP,_

Remote Control Unit

(UREMT32SR022)

2 AA Batteries

Magnet

(0EM403452)

Matching Adapter

(46-45733-3)

Dipole Antenna

(46-82'117-3)

Swivel (upper _iece)

Swivel (Foundation)

(0EM 100779)

3 Screws

, i(46_57569_3)

If you need to replace these accesgorles, please i'efer to the PART NUMBER located under each illustration

and contact the Sears Parts Department to order.

-7-

6F06

OPERAI ING CONTROL_i AND FUNISI ION5

- FR! iNT VIEW -

1 2 3 4 5 6 7 8 9 10 11 12 3

- REMOTE CONTROL VIEW -

SPEED SLOW

qDq

_REWIND PLAY Ip

RECORD STOP •

SELECT

ADD/ ;

DELETE !

C.RESET :

F.FWDi_I

PAUSFJSTtLL

1. AUDIO input Jack- Connects audio output jack of

your audio equipment or another VCR to the unit.

2. VIDEOinput jack- Connects video output jack of

your video camera or another VCR to the unit.

3. RECORD indicator-Flashes during recording.

Lights up in the Stand-by mode for Timer Recording.

4. POWER button-Turns TV/VCR on and off. Press

to activate the Automatic Timer Recording mode.

5. STOP button Stops the tape.

EJECT button- Press while in the STOP mode to

remove a tape from the TV/VCR.

6. REWINDbutton- Rewinds the tape. Press during the

PLAY mode to view the picture rapidly in reverse.

7. PLAYbutton- Begins playback of a recording.

8. F.FWDbutton-Rapidly advances the tape. Press

during the PLAY mode to view the picture rapidly in

forward.

9. REC button- Begins manual recording.

OTR button- Activates the One Touch Recording.

(located only on the TV/VCR unit)

10. VOLUME_ buttons- Adjusts the volume level.

11. CHANNEL _ buttons- Selects the channel for

viewing or recording.

PICTURE CONTROL function-Adjusts the picture

control. This function is available only from the

remote control. (See page 19)

TRACKING +1-function- Minimizes video 'noise'

(lines or dots on the screen) during the Play mode.

(See page 21)

12. EARPHONE jack-Connects earphones (not sup-

plied) for personal listening. The size of jack is 1/8"

monaural (3.5mm).

13. Cassette compartment

-8-

6F06

- REAR VIEW-

IIIIIII IIIIIIIIII Iiliiiiiii IIililIIIIIIIi IV

I ANT. I

14. NUMBER buttons- Selects desired chaian_el's for 21.

viewing or recording. To select channels 1 to 9, press

the 0 and the desired channel.

+1O0 button- Selects 100+ cable channels. To select

channel 125, first press the "+100" button and then

press "2" and "5".

15. ALARM button- Sets the time to have the TV/VCR

automatically turn on. (See page 30) 22.

16. SPEED button-Sets desired recording speed.

(SP/LP/SLP)

17. PAUSE/STILL button- Used to temporarily stop the

tape during the recording or to view a still picture

during playback.

Frame advance function- Press to advance the pic-

ture by one frame during the still mode. 23.

18. SLOW button- Press to reduce the playback speed.

Slow speed can be controlled by pressing F.FWD 24.

button (faster) or REWIND button (slower).

19. SLEEP button- Sets the Sleep Timer. (See page 30) 25.

20. C.MEMOR¥ button- Turns counter memory on and

off. (See page 23)

ADD/DEL_TE button-'_elete_ 'or adds channel

numbers in the Channel Set Up mode (See page 14).

Press to cancel a setting program (such as setting

clock or timer program) (See page 28)

NOTE: These functions are operative only during

the ON-SCREEN menu mode.

C.RESET button-Resets counter to 0:00:00.

SELECT button-When setting program (for

example: setting clock or timer program), press to

determine your selection and to proceed to the next

choice.

DISPLAY function- Displays on the TV screen

either the counter or the current channel number and

current time. (See page 18)

MENUbutton-Displays main menu on the TV

screen.

MUTE button- Mutes the sound. Press it again to

resume sound.

ANT. terminal- Connects to an antenna or CATV.

- 9 - EN

6F06

i'REI'ARAI'ION I OR

VItI_TUHF COMBINED ANTENNA

The VHFAJHF Rod Antenna (supplied) is detachable.

Insert the stem of the antenna into the hole on the upper-

back portion of the TV/VCR.

Connect the VHF/UHF Rod Antenna or VHF/UHF

Combination Antenna to the ANT. terminal of the

TV/VCR as shown in the diagram below.

For the best reception, fully extend the VHF/UHF Rod

Antenna and make the necessary adjustments.

(Avoid touching the top section when adjusting.)

Dipole Antenna(Supplied) VHF/UHF Antenna

,,I .i , • J

NOTE :

Before plugging the Rod antenna into antenna terminal,

check that the pin is not bent. If it is bent, straighten the

pin first before plugging the cable into antenna terminal.

Bent pin

(Needs to be straightened)

(Straight pin)

VHF/UHF SEPARATE ANTENNAS

It is necessary in some areato use an outdoor antenna.

VHF Antenna

Antenna

Flat twin-lead cable

. t ....

. .. ..

-10-

6F06

CABLE WITHOUT CONVERTER/

DE-SCRA MBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels

2) Program one or more unscrambled channels for

Automatic Timer Recording.

From Cable System

75-ohm

Coaxial Cable

(not supplied)

ANT.(_

CABLE WITH

CONVERTER/DE-SCRAMBLER BOX

If your cable service supplies you with aconverter box,

you can use the basic connection shown below.

By using this connection you can record and view any

channel including scrambled channels. However, chan-

nel selection must be made using the converter box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended recording is

limited to one channel at a time.

Box (not suppiled)

,From Cable System

75-ohm

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

1. Set the TV/VCR channel selector to the output

channel for the Cable Converter Box. (Ex. CH3)

2. Select which channel to record from your Cable

Converter Box.

NOTE: When using a cable converter box, you cannot

record one channel and view another.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected

to the grounding system of the building as close to the point of cable entry as practical.

-11-

6F06

When using an cxternal input signal (another VCR or

camcorder), connect the player's audio/video output

cables to the AUDIO IN, VIDEO IN jacks on your

TV/VCR. Then, press AUX

CHANNEL • or • button or

enter "00" so that "AUX"

screen appears.

• )

I .

1) Open the battery compartment cover by pressing the

cover on the remote unit in the direction of the arrow.

2) Insert 2 "AA" penlight batteries into the battery com-

partment in the direction indicated by the polarity

(+1-) markings and replace the cover.

1) Remove the film sheet from the magnet and install

onto the back of the remote control as shown.

2) You can stick the remote control onto any metal

surface, such as a refrigerator door.

3) Please be aware that slamming of door may cause the

remote control to fall from door and damage remote.

CAUTION:

• When sticking the magnetic remote control onto a

refrigerator door, place it closer to the hinge-end of

the door so when the door closes it doesn't knock off

the remote control.

1) Carefully place the TV/VCR upside down and attach

the assembled swivel to the bottom of the TV/VCR

as shown.

2) Put the screw (supplied) into the holes marked by the

arrow.

T IT

3) Place the TV/VCR right-side up. You now can rotate

the TV/VCR in either direction.

CAUTION:

• Always place the swivel on a flat surface.

- 12- EN

6F06

} llJq_A) k_A_E i i L

This TV/VCR will operate with any cassette that has the VHS mark. For best results, wc lcconlmend the use ol

high-quality tapes. Please do NOT use poor quality or damaged tapes.

PRECAUTIONS

• Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a warm

place. When using a tape under these conditions, wait

until the tape has warmed to room temperature and

the moisture has evaporated to avoid a damage to the

tape and your TV/VCR.

• Avoid exposure to extreme heat, high humidity, and

magnetic fields.

• Do not tamper with the cassette mechanism.

• Do not touch the tape with your fingers.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Gently push

on the back center portion of the cassette continuously

until it is drawn into the TV/VCR.

The TV/VCR will automatically turn on.

b__ jj ,, i ..... _.,.,

CORRECT WRONG

THREE DIFFERENT TAPE SPEEDS

Select the desired tape speed format before recording:

SP Mode: Standard Play

LP Mode: Long Play

SLP Mode: Super Long Play

The table below shows the maximum recording/play-

back time when using a T60, T120, or T160 tape in each

mode.

Tape Speed

of tape

SP mode

LP mode

SLP mode

Recording/Playback Time

T60 T120 TI60

1hour 2 hours 2-2/3 hours

2 hours 4 hours 5-1/3 hours

3 hours 6 hours 8 hours

REMO VING A CASSETTE

1) In the Stop mode, press EJECT button on the remote

control or press STOP/EJECT button on the

TV/VCR. The TV/VCR will eject the tape.

2) Pull the cassette out of[

the cassette compartment I

and store in its case as I

shown. [

ERASE PREVENTION

Breaking off the plastic tab

from the back edge of the

cassette prevents accidental

erasure of your recording.

Tab

If you dedide t0 record on

the tape again, simply cover [

the hole with tape. /

-13- EN

6F06

When first using the fV/VCR, you may want to select

language (English or Espafiol=Spanish) and preset the

tuner to show only the channels you receive in your area.

You must use the remote control for the following

steps.

NOTE: Channel memory programming is not needed

when using a converter/de-scrambler box.

Channcls that you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channels to the memory again.)

1 Select "CHANNEL SET UP"

Ill_ -MENU-

'riMER PROGRAMMING

P_CTURE CONTROL

SETTING CLOGK

CHANNEL SET UP

USER'S SET UP

LANGUAGE ENGLISH]

CAPTION [OFF]

"rIME SEARCH

INDEX SEARCH

Press MENU button to move to

.................................................................... CHANNEL SET UP" and press

1 Plug the TV/VCR power cord

into a standard AC outlet.

SELECT button.

2 Turn on the TV/VCR

3 Select "ENGLISH" or "ESPAI_IOL"

,S&

Select by using the CH • or!'

button. "[ ]" indicate the selected

language.

I_ -SETUP -

LANQUAGE

IENGLISHI ESPAROL

AUTOPRESET

4 Begin auto preset -=TOP-

LANGUAGE

Press MENU button to move to ,EN_,_.]ESPA_

"AUTO PRESET" and press ..........

SELECT button.

The tuner scans and memorizes

all the active channels in your area.

NOTES: ' '

• The TV/VCR distinguishes between standard TV

channels and CATV automatically.

• If you want to play or record a video tape BEFORE

presetting the tuner, you must press MENU button.

To preset the tuner again, see "AUTO PRESET

AGAIN".

5 After scanning

The tunerstopsatthelowestmemorizedchannel.

(TV mode: from CH 02/CATV mode: from CH 01)

Should you want to recall the selected channels, you can

select the desired channel by using the remote control

number buttons or CH • or V.

TO RETURN TO TV MODE WHEN

SCANNING

Press MENU button in scanning mode.

2 Select "ADD/DELETE CH"

II_ - CHANNEL SET UP -

Press MENU button to move to _v,cA_ [_ ]

"ADD/DELETE CH" and press AU,OPRESE_

SELECT button. AD_,OELE__N

3 Enter the desired channel number

Press CH • or• button until the ADS_ELE_EON

desired channel number appears. D, __,}

You can also use the number but-

tons to enter it.

, r

4 Delete (or add) itfrom (into) memory

Press ADD/DELETE button. The channel number

changes to light red. The channel is deleted from

memory.

• To delete another channel, repeat steps [3]and [4].

• If you press the ADD/DELETE button again, the

channel is added to memory again.

Added channel : Light blue.

Deleted channel : Light red,

5 Exit the channel setup mode

Press MENU button to return to TV mode.

NOTE: If you wish to confirm that channel(s) has been

deleted or added, press CH • or • button.

-14- EN

6F06

1 Setect"CHANNEL SET UP"

retontooveto[......1

TIMER PROGRAMMING

"CHANNEL SET UP" and press sEn,NoP'C.... CLOCKCON....

CHANNELSET up

SELECT button. OSER'SSETUR

LANGUAGE ENGLISH]

CAPTION {CAPTION 1]

TIME SEARCH

INDEX SEARCH

2 Select "TV" or "CATV"

Select [TV] or [CATV] by using

CH • or • button.

[ ON°NELS°°P:t

_,CA_ ._,

ALrro PRESET _" |

ADD / DELETE CH

3 Begin auto preset . -O"=.ELS_uP-

Press MENU button to move to _,CA_ _r,

AUTO PRESET

"AUTO PRESET" and press ........ CH

SELECT button.

The tuner scans and memorizes

all the active channels in your area.

4 After scanning

The tuner stops at the lowest memorized channel.

(TV mode: from CH02 / CATV mode: from CH01)

1 Selec_ "LANGUAGE'

Press MENU button to move to "LANGUAGE".

2 Select "ENGLISH" or "ESPAIqlOL"

Select "ENGLISH" or

"ESPAIqOL = Spanish" using

CH • or • button.

II_ -MENU-

"rIMER PROGRAMMING

PICTURE CONTROL

_ml'rtNG CLOC K

CHANNEL SET UP

USER'S SET tip I 4P

LANGUAGIcI_3USH] In

CAPTION I(_NI_,

TIME SEARCH --

INDEX SEARCH

3 Exit the Language mode

Press MENU button until TV/VCR returns to TV mode.

Select the "D.S.T." feature and the TV/VCR's clock

automatically will spring ahead one hour in April, then

fall back one hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

• First Sunday of April : from 2:00AM to 3:00AM

(summer time): When a recording is programmed to

start between 2:00AM - 2:59AM on this day, the

TV/VCR will start recording at 3:00AM.

• Last Sunday ofOctober : From1:00AM to 2:00AM

When a recording is programmed to end between

1:00AM - 1:59AM on this day, the TV/VCR will stop

at 2:00AM.

r* :

Make sure ... _,,_ ..... _

• Press POWER button t0 _tn on the TWVCR.

• Use the remote control for the following steps.

1 Select "SETTING CLOCK"

[

Press MENU button to move to -_E, U-

TIMER PROGRAMMING

"SETTING CLOCK" and press _ _,_P'°.... =C_"°L_

SELECT button. CHA.NE_U_E.,SSET_....uP

LANGUAGE ENGUSH]

CAPTION [O_F]]

TIME SEARCH

INDEX SEARCH

2 Set "D.S.T." (Daylight-Saving Time) to [ON]

Press MENU button to move to ( -_E_.N_C_O_-

)

"D.S.T". [ A_OCL0_NtO"]/

3 Set "D.S.T." to [ON] .=UALC_O_S_,_..,,_/

Press CH • or • button until .... s.,. ._o_k.]

[ON] appears.

4 Exit the Daylight-Saving Time mode

Press MENU button until TV/VCR returns to TV mode.

TO CANCEL THE D.S.T. FUNCTION

Repeat steps [1] to [3]. Press CH • or • button until

[OFF] appears andthen press MENU button to returnto

the TV mode.

- 15 - EN

6F06

Set the clock accurately for proper automatic timer

recording. If the Public Broadcasting Station (PBS) is

available in you area, follow "AUTO CLOCK

SETTING". If it is not, follow "MANUAL CLOCK

SETHNG".

AUTO CLOCK SETTING

You can have the TV/VCR set the clock automatically

by using the Public Broadcasting Station (PB S) channel

in your area. Once you have set the clock by using the

following procedure, the TV/VCR will automatically

monitor the correct time and date being broadcast by the

PBS station in your area, using a new service called

Extended Data Service (XDS).

Make sure ...

• Confirm that the antenna connections are correct.

• The cable converter box must be turned on if your

TV/VCR is connected directly to it. (See NOTES)

• Use the remote control for the following steps.

NOTES:

• Auto clock setting only needs to be set once, but can

be done again if the clock's time has become

incon_t for some reason.

• If the TV/VCR is connected directly to a cable

converter box, the local PBS station must be selected

on the cable box itself, and the TV/VCR must be set

to the output channel of the cable converter box

(usually channel 3 or 4), to be able to set up and

automatically correct the clock.

The TV/VCR cannot control the channels of the

cable converter box.

1 Select"SETTING CLOCK"

Press MENU button to move to

"SETTING CLOCK" and press

SELECT button.

Ill" -MENU-

TtMER PROGRAMMING

PICTURE CONTROL

SETnNG CLOCK

CHANNEL SET UP

USER'S SET UP

LANGUAGE [ENGLISH]

CAPTION CAPTION1]

TIME SEARCH

INDEX SEARCH

2 Set "AUTO CLOCK" to [ON]

IF - SETTING CLOCK -

Press CH • or • button until A_OCtocN_f.

[ON] appears. A......... i_j

MANUAL CLOCK SET

t r 0, S T, [_

3 Enterthe channel number for the PBS station

Press MENU button and use the CH • or • button until

the channel number for your local PBS station appears.

If you do not know the PBS

channel number, leave it set to

[AUTO]. The TV/VCR will

search automatically all avail-

able channels for the local PBS

station, and will select that

channel.

Ill_ - 8E'_I'INI3 CLOCK -

AOrOOLOCN_ 1

4 Exit the Auto ClockSetting

Press MENU button until TV/VCR returns to TV mode.

5 Turn off theTVNCR

Press POWER button to turn off the TV/VCR for search-

ing the local PBS station. The power must remain off

during this search.

If yon enter the channel number manually,

• it may take for about a few minutes for this search to

be completed.

If you choose [AUTO],

• the TV/VCR must search through all the available

channels. It must scan each channel for a couple of

minutes to determine if that channel is transmitting

the XDS signal, because the PBS station will send

this signal only once every minute. This search could

take up to 2 hours. You may want to start this channel

search at night when the unit is not in use.

• if the time that is automatically set by this selected

PBS station is incorrect, it may not be your local PBS

station, but one from a different time zone. Or there

is a case that no channel is broadcasting the XDS

signal in your area, as shown by no time being set

even after an overnight search. In these cases, you

must manually enter the correct local PBS station, or

set the clock manually, turning off the Auto Clock

Setting feature.

- 16 - EN

6F06

Make sure ...

• The remote control needs to be used.

• Power must be turned on.

In the example below, the clock will be ,sel lo:

March 1st, 1996 at 5:40PM

1 Select "SETTING CLOCK"

Press MENU button to move to I_ MENU-

TIMER PROGRAMMING

"SETTING CLOCK" and press _'N_'CTU"EOONmOL_LOC_

CHANNEL _ET UP

SELECT button. U_R'ES_TU_

LANGUAGE ENGLISH_

CAPTIGN [C_PTION1 ]

TIME SEARCH

• IOEKS_EARCH

2 Select "MANUAL CLOCK SET"

Press MENU button to move to I_ -s_,N_LOC_

AUTO CLOCK [O_ I

"MANUAL CLOCK SET" and ......... t,uToj

press SELECT button. _ .... oe_E_TM

D S T [OFF]

3 Select the month

Press CH • or • button until

your desired month appears and

press SELECT button.

EXAMPLE: 03 = March

OUR MINUTE

4 Select the day

Press CH • or • button until

your desired day appears and

press SELECT button.

EXAMPLE: 01 = 1st

MANUAL CLOCK SET -

MONt._ YEAR

o_ -,0i¢-.....

HOUR MINUTE

5 Select the year

Press CH • or • button until

your desired year appears and

press SELECT button.

EXAMPLE: 1996

- MANUALCLOCKSET - |

DAY _

.... 1

HOUR : MINUTE J

6 Select the hour

Press CH • or • button until

your desired hour appears and

press SELECT button.

EXAMPLE: 5PM

I - MANUAL CLOCK SET -

MONTH DAY YEAR

03 01 FR_ tgg_

H R MIN

mo5 m -_PM

S1% #1%

7 Select the minute _MANUA_CLOC_SET-

Press CH • or • button until the MONTROAY YEAR

03 01 FRI 1996

desired minute appears.

EXAMPLE: 40 o, -_%,_

8 Start the clock

Press MENU or SELECT button.

Although seconds are not

displayed, they begin counting

from 00 when you press MENU

or SELECT button. Use this

feature to synchronize the clock

with the correct time.

5:40 PMl

• This unit has a built-in calendar up to the year 2010.

TO CHANGE CLOCK SETTING

l) Follow steps [1] and [3].

2) Select where you want to change using SELECT

button or ADD/DELETE button.

3) Enter correct numbers using CH • or • button.

4) Press MENU or SELECT button to start the clock.

PLEASE NOTE:

If there is no local PBS station in your area or on your cable system, select "AUTO CLOCK " andpress CH • or

• button to turn [OFF] this function. You can then manually adjust the clock.

- 17 - EN

6F06

1o chcck lilt Ct)untcl, k:lock and Channel number on the TV screen, press SELECT button on the remote control.

Each time you press SELECT button on the remote control, the TV screen will change as follows:

When the Closed Caption mode is OFF:

OFF mode Counter mode Clock mode

• Counter mode: After 5 seconds, only

the counter remains. To clear it, press

SELECT button.

• Clock mode: After 5 seconds, only the

clock and the channel number remain.

To clear them, press SELECT button.

STOP ]

SP OOUNT 0:12:34

After5 seconds

COUNT 0:12:34 /

Counter

remains

............................................. o

•,_ After 5 seconds

5:40PM

CH2

Clock & Channel

remains

When the Closed Caption mode is ON:

• The On-Screen Display disappears after 5 seconds.

• This is true even if MUTE button is pressed, or

PAUSE/STILL button is pressed while recording.

OFF mode

SPECIAL FEATURES

Clock/Counter mode

SP COUNT 0:I 2:34

Magnetism from nearby appliances orthe magnetic re-

mote might affect the color of the TV picture.

If this happens, move this unit away from the appliance.

If the color is still not correct, disconnect power cord

from AC outlet and reconnect it after 30 minutes.

• When the end of a tape is reached during recording,

playback, or fast-forward, the tape automatically

rewinds to beginning, ejects, and TV/VCR turns off.

• This function is operative when Auto Repeat is set to

the [OFF] position.

• The tape will not auto-rewind during timer recording

or One Touch Recording.

• When tape is rewound to the preset memory position

of the Counter Memory during Auto Rewind, the

tape will not eject and the TV/VCR will not turn off.

-18- EN

6F06

t +" Ut+IEI+A 1 I¢07+

1 Turn on the TV/VCR

VOLUME 20

IlllhlliHit

2 Select the channel number

Press CH • or • button toselect

your desired channel number.

3 Adjust sound

Press VOLUME • or • button

to adjust the volume.

This function enables you to adjust the TV screen

making it suitable to use for a TV GAME.

CH 06

Make sure ...

You must use the remote control unit for the following

steps:

1 Select "USER'S SET UP"

PressMENU button to move to

"USER'S SET UP" and press

SELECT button.

-MENU- 1

"r_MER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

l- USER'S SET UP

LANGUAGE ENGLISH]

CAPTION lC_

PTIONll

Tk_IE SEARCH

INDEX SEARCH

2 Set "GAME MODE"to [ON]

Press CH • or • button until It -U_R'SEErO,+_.

[ON] appears. _+E_ODE

RENTAL

REPEAT PLAY [OFF]

AUTO RETURN [OFF}

3 Exit the Game mode

Press MENU button until the TV/VCR returns to the TV

mode.

TO CANCEL THE GAME MODE

Repeat step [1] and [2], selecting [OFF]. Press MENU

button to return to TV mode.

The TV/VCR's picture controls - BRIGHT,

CONTRAST, COLOR, TINT and SHARPNESS -

are preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a naturallooking image.

NOTES:

• Procedures must be followed within 5 seconds or the

Picture Control mode will be cancelled.

• When setting the Picture Control, the Game mode

will automatically set to [OFF].

Make sure ...

• Use the remote control unit for the following steps:

1 Select "PICTURE CONTROL"

Press MENU button to move to

"PICTURE CONTROL" and

9ress SELECT button.

II_ -MENU- '

ER PROGRAMMING

I_I_EUR E CONTROL

SETTING CLOCK

CHANNEL SET UP

USER'S SET UP

GUAGE ENGLISH

_APTION IC_PTIONI }

"lIME SEARCH

INDEX SEARCH

" -_ ......... ._ : - lllll wJl LiE ........... _+

2 Select the item you want to adjust

Press SELECT button until the desired control is

displayed. Each will appear in sequence on the TV

screen.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

-kJSlil3_l +; r Lt.Li

i,| / i rll _ II

3 Adjust the picturecontrol

Press CH • or • button to adjust to

i,i i,i i r u Oliiii

tour desired level.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

CH •

to decrease

brightness

to decrease

contrast

to pale

to purple

to soft

CH •

to increase

brightness

to increase

contrast

to brilliant

to green

to clear

- 19 - EN

6F06

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTIONmode: This allows you to watch programs

and at the same time see the dialogue captions.

TEXTmode: This allows you to view a full screen of

text information.

1/2: You may get these captions or text information by

selecting either "1" or "2". "2" is used usually for a

second language if available.

NOTE:

Not all programs are broadcast with closed captions.

Your television is designed to provide error free closed

captions from high quality antenna, cable and VCR

signals. Conversely, poor quality signals are likely to

result in caption errors or no captions at all. Common

signal conditions which may cause captions errors are

listed below:

• Automobile ignition noise.

• Electric motor brush noise.

• Weak snowy reception on TV Screen.

• Multiplex signal reception displaying picture ghosts

or airplane flutter.

• Playback of poorly recorded or worn VCR tapes.

If the TVNCR displays a black box

on the TV screen, this means that

the TV/VCR is set to the TEXT

mode. To clear screen, select

[CAPTION1], [CAPTION2] or

[OFF].

Make sure ....

' • Use the remote contr_)l unit for the following Steps.

• Power must be turned on.

Select "CAPTION"

Press MENU button to move to

"CAPTION".

II_ -MENU-

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER'S S T P

CAPTI_I_t OFF

INDEX SEARCH

2 Select yourdesired caption menu

Press CH • or • button until -, E. u- 1

your desired caption menu ,_E,P,OORAMM,Na

PICTURE CONTROL

appears, s_,.G°LOCK

CHANNEL SET UP

USER'S SET UP

([CAPTION 1], [CAPTION2], _._u,_E_L_l

CAPTIO PTIONI] m

TIME SEA

[TEXTI] or [TEXT2]) , ....._J •

3 Exit the caption setting mode

Press MENU button until TV/VCR returns to TV mode.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], selecting [OFF] using CH •

or • button.

WHEN THE CLOSED CAPTION MODE

IS ON

The On Screen Display will disappear after 5 seconds.

• This is true when MUTE button is pressed and when

PAUSE/STILL button is pressed while recording.

- 20 -

6F06

Page is loading ...

Zenith SRV1341W Operating Manual & Warranty

Brand: Zenith

Model: SRV1341W

Category: CRT TVs

Type: Operating Manual & Warranty

This manual is also suitable for

SRV1341

Download PDF

report

Zenith SRV1341W Operating Manual & Warranty

This manual is also suitable for

Zenith SRV1341W Operating Manual & Warranty

Related papers

Other documents