Columbia Lighting CNW Narrow Wrap User manual

Brand: Columbia Lighting

Model: CNW Narrow Wrap

Type: User manual

701 Millennium Blvd • Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com

Page 1/2 Rev. 10/06/21

COL-CNW-ins

CNW Instruction Manual

CNW

NARROW WRAP

STEP 1

Remove the lens from the housing by pressing the provided suction cup to the lens near one end of the luminaire.

Pull up on the suction cup to detach the lens from the luminaire housing.

SURFACE MOUNTING

CAUTION! — READ THIS FIRST — IMPORTANT SAFETY INSTRUCTIONS

WARNING

• To reduce the risk of death, personal injury or property damage from ﬁre, electric shock, falling parts, cuts/abrasions, and other hazards read all

warnings and instructions included with and on the ﬁxture box and all ﬁxture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should be performed by a qualiﬁed licensed electrician.

• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualiﬁed licensed electrician and check your

local electrical code.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

• Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.

WARNING

• Turn o electrical power at fuse or circuit breaker box before wiring ﬁxture to the power supply.

• Turn o the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

• Risk of burn. Disconnect power and allow ﬁxture to cool before handling..

NOTICE: Green ground screw provided in proper location. Do not relocate.

NOTICE: Minimum 90° supply conductors.

NOTICE: Speciﬁcations and dimensions subject to change without notice.

NOTICE: Suitable for Dry or Damp location.

NOTE: Components shown in images are

representative only and may vary based

on the conguration ordered.

LED DRIVER

Black (Line)

White (Neutral)

120—277V

Green (Grd)

Dimming wire

to 0—10V IEC

compliant control

ad wire to

LED load

Pink (Dim+)

Blue (-)

Red (+)

Gray (Dim-)

General Wiring Diagram

REMOVE

Lens

Suction cup APRESS

Housing

Lens

Housing

BPULL

CNW

NARROW WRAP

701 Millennium Blvd • Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com

Page 2/2 Rev. 10/06/21

COL-CNW-ins

CNW Instruction Manual

Switch

Iout(mA)

Pout(W)

Iout(mA)

Pout(W)

Switch

Iout(mA)

Pout(W)

Iout(mA)

Pout(W)

3500K 4000K 5000K

800 700 600

35 30

III III

STEP 4

Install the lens, starting at one end of housing. Insert lens slot onto edge of housing. Carefully squeeze the lens to engage opposite side with housing. Continue this

action down length of lens until fully installed onto housing.

STEP 3

Place the luminaire on the junction box and pencil the four hole positions onto the ceiling. Put the luminaire aside and drill the four holes.

Insert an anchoring bolt (not included) into each hole. Screw the four mounting screws into each anchoring bolt, then connect the AC wires.

STEP 2 — (FOR LSCS VERSIONS ONLY)

Dierent lumen and correlated color temperature levels can be achieved by setting the switch on the driver cover to dierent positions:

25W = 3000 lm ; 30W = 3500 lm; 35W = 4000lm

Junction box

Ceiling

Wiring

Anchors

Mounting screws