MODEL: 6340
4-1/2" ANGLE GRINDER
SPECIFICATIONS
Important Warnings - Grinders & Cut-Off Tools
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and ttings should have the same inside dimensions.
Air Supply
Model No.
Free
Speed
(RPM)
Motor
(HP)
Collet / Wheel
Size (in) Gears Exhaust Weight
(lbs.)
Length
(in)
Air
Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
6340 11,000 1.0 4-1/2 Spindle Drive Rear 2.25 8.75 6 3/8 1/4 NPT
MODEL: 6340
4-1/2" ANGLE GRINDER
Exploded View & Parts List
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
01 915401 REGULATOR 1 28 925433 CLAMP NUT 1
02 9OB-02 O-RING 1 29 925534 SPINDLE HOUSING 1
03 9288303 O-RING 1 30 925535 SPINDLE 1
04 9OB-30 SNAP RING 1 31 9288734 BEARING 2
05 9OB-04 O-RING 1 32 924031 PINION GEAR 1
06 9E-05 VALVE STEM 1 33 9254B39 ANGLE HOUSING 1
07 915407 AIR INLET NPT (US) 1 34 921029 OIL CUP 1
915407-2 AIR INLET BSP (UK) 1 35 910015 SNAP RING 1
08 915408 MUFFLER 1 36 9254B64 NUT 1
09 9288309 SILENCER 1 37 9254B62 SPRING 1
09-1 915459 STAINLESS MESH 1 38 9254B63 PIN (12T) 1
09-2 9288309-1 SILENCER 1 39 925440 WASHER 1
10 970011 O-RING 1 40 925441 BEARING 1
11 9288314 SPRING 1 41 924035-1 PINION GEAR (23T) 1
12 9288315 VALVE 1 42 925444 BEARING 1
13 9288316 WASHER 1 43 921538 NUT 5
14 929014 PROTECTING RUBBER 1 44 925446 SCREW 1
15 915416 HOUSING 1 45 925447 HANDLE LINK 1
16 9200A13 SAFETY THROTTLE 1 46 925448 FACE PLATE 1
17 912012.1 SPRING PIN 1 47 981317 SCREW 4
18 922536A BEARING 1 48 929548 4-1/2 INCH DISC COVER 1
19 915419A REAR PLATE 1 49 9288542 SCREW 4
20 915422 ROTOR BLADE 4 50 985562A DISC NUT (US)
DISC NUT (US)
1
21 925523 ROTOR 1 985562.1A DISC NUT (UK) 1
22 915424 CYLINDER 1 51 985563A 1
23 970018 PIN 2 985563.1A DISC NUT (UK) 1
25 929527 FRONT PLATE 1 52 987057 DISC SPANNER 1
26 970048A BEARING 1 53 970402.2 4-1/2" GRINDING WHEEL 1
27 925432 NUT 1 54 70410 SNAP RING 1
55
929555 SHAFT (US) 1
929555.1 SHAFT (UK) 1
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Husky H4830 User manual
-
Florida Pneumatic FP-711A User guide
-
Dynabrade 50302 Safety, Operation And Maintenance
-
-
-
-
-
-
Dynabrade 50360 Operating, Maintenance And Safety Instructions
-
Sunex SUNSX5206 User manual
