Husky H4830 User manual

Type
User manual

Husky H4830 is a powerful air sander designed for smoothing and shaping wood, metal, and plastic surfaces. Its variable speed control allows for precise adjustment to suit different materials and tasks. The sander features a lightweight and ergonomic design for comfortable handling, reducing fatigue during extended use. Additionally, the H4830 includes a variety of sanding pads for different grits and applications, making it a versatile tool for any DIY enthusiast or professional.

Husky H4830 is a powerful air sander designed for smoothing and shaping wood, metal, and plastic surfaces. Its variable speed control allows for precise adjustment to suit different materials and tasks. The sander features a lightweight and ergonomic design for comfortable handling, reducing fatigue during extended use. Additionally, the H4830 includes a variety of sanding pads for different grits and applications, making it a versatile tool for any DIY enthusiast or professional.

7 HUSKYTOOLS.COM
Please contact 1-888-43-HUSKY for further assistance.
Maintenance
Ensure the air line is shut-off and drained of air before removing this tool for service. This will prevent the tool from operating if the throttle
is accidentally engaged.
Troubleshooting
Problem Possible Cause Solution
The tool runs slowly or will not
operate.
There is grit or gum in the tool. Flush the tool with air tool oil or gum solvent.
.
.
The air pressure is low. Adjust the regulator on the tool to the
maximum setting.
Adjust the compressor regulator to the tool’s
maximum setting of 90 psi.
The air hose leaks.
tape if leaks are found.
The air pressure drops. Ensure the hose is the proper size. Long
hoses or tools using large volumes of air may
require a hose with an I.D. of ½" or larger
depending on the total length of the hose.
Do not use a multiple number of hoses
connected together with a quick connect
. This causes additional pressure drops
and reduces the tool power. Directly connect
the hoses together.
There is a worn rotor blade in the motor. Replace the rotor blade.
There is a worn ball bearing in the motor. Remove and inspect the bearing for rust, dirt, and
grit. Replace or clean and grease the bearing with
bearing grease.
There is moisture blowing out
of the tool’s exhaust.
There is water in the tank. Drain the tank. (See the air compressor manual
for instructions.) Lubricate the tool and run it until
water is not evident. Lubricate the tool again and
run for 1-2 seconds.
8
Service Parts
Reference
Number
Part Number Description Reference
Number
Part Number Description
1 9OB-03 Snap Ring 23 9OB86823 O-Ring
2 9OB-04 O-Ring 24 981326 Pin
3 9ST316003 Valve Stem 25 9STOB-25 Front Plate
4 9OB-02 O-Ring (2) 26 9OB-26A Bearing
5 9ST316005 Regulator 27 9OB-28.1 Washer
6 9OB-06 Washer 27A 9OB-28 Washer
7 9STOB-08 Valve 28 9ST246027 Washer
8 9OB-09-1 Spring 29 9ST70407 Key
9 970426 Air Inlet 30 9STS560-29 Motor Shaft Balancer
10 9SX-11.1 Stainless Mesh 31 9OB-30 Snap Ring
11 9SX-11 Silencer 33 9OB-33 Snap Ring
12 9ST246011 Sleeve 34 9S560-34 Shaft
13 9OB86811-1.1 Lever (Red) 35 9ST246034 O-Ring
14 9OB-101-14 Pin 36 9RS0134 Lock Nut
15 9OB86813-1.3 Housing (Black) 37 9ST2460N36 Shroud
16 970410 Retaining Ring 38 5430 PSA Pad
17 970048A Bearing 38 5430H Velcro Pad (Optional)
18 9STOB-19 Rear Plate 42 9BTOB-39-22 Stop Spanner
19 9OB-20 Rotor Blade 45 9OB-31.3 Bearing
20 9STOB-21 Rotor 46 9OB-23.2A Shim
21 9ST246021 Cylinder 47 9OB-31.4 Bearing
22 9OB-23 Pin 48 9OB86848 Rubber Wsher
33
34
35
37
36
38
9
4
3
2
1
15
16
17
18
19
20
25
26
27A
29
30
6
7
8
14
5
13
31
27
28
23
21
22
24
45
46
47
10
11
12
42
48
  • Page 1 1
  • Page 2 2

Husky H4830 User manual

Type
User manual

Husky H4830 is a powerful air sander designed for smoothing and shaping wood, metal, and plastic surfaces. Its variable speed control allows for precise adjustment to suit different materials and tasks. The sander features a lightweight and ergonomic design for comfortable handling, reducing fatigue during extended use. Additionally, the H4830 includes a variety of sanding pads for different grits and applications, making it a versatile tool for any DIY enthusiast or professional.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI