LG Electronics 30FZ1DC User manual

Color television

OWNER’S MANUAL

Please read this manual carefully and completely before

operating your TV.

Retain this manual for future reference.

Record model number and serial number of the TV in the

spaces provided below.

See the label attached on the back cover and relate this

information to your dealer if you require service.

Model Number :

Serial Number :

MODELS: 30FZ1DC

32FZ1DC-UB

LG Electronics U.S.A., Inc.

R

TruSurround XT

PAGE 2

WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip-

ment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

LG Electronics U.S.A., Inc

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

1-800-243-0000

http://www.lgusa.com

PAGE 3

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or

sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa-

ratus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.

The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be

included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by

adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing

that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

(Continued on next page)

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or

the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an elec-

trician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the appara-

tus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

PORTABLE CART WARNING

IMPORTANT SAFETY INSTRUCTIONS

PAGE 4

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that

is, a single outlet circuit which powers only that appliance and has no

additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power cords, or damaged or

cracked wire insulation are dangerous. Any of these conditions could

result in electric shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the

cord exits the appliance.

16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

17. Wet Location Marking :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

PAGE 5

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Instructions . . . . . . . . . . . . . . . . .3-4

Step 1. Hook Up TV

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . .6

Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . .7

Front Connections Panel (FRONT VIDEO) . . . . . . . . . . . .8

ANT/Cable Service Hookup . . . . . . . . . . . . . . . . . . . . .9

Cable Box Connections . . . . . . . . . . . . . . . . . . . . . . .10

VCR Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .11

DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Set-top Box Hookup . . . . . . . . . . . . . . . . . . . . . . . .13

Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . .14

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Remote Control Functions in TV Mode . . . . . . . . . . .16-17

Turning the TV on . . . . . . . . . . . . . . . . . . . . . . . . . .18

On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .18

Step 2. Customize your TV’s Features

SETUP Menu

EZ Scan (Channel Search) . . . . . . . . . . . . . . . . . . . .19

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

DTV Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Degaussing the screen . . . . . . . . . . . . . . . . . . . . . .21

Channel Label Setup . . . . . . . . . . . . . . . . . . . . . . .22

Input Source Selection . . . . . . . . . . . . . . . . . . . . . 23

VIDEO Menu

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Manual Video Control . . . . . . . . . . . . . . . . . . . . . . .25

Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . .26

XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

AUDIO Menu

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . .27

EZ SoundRite . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . .28

EZ Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Manual Sound Control . . . . . . . . . . . . . . . . . . . . . .29

TV Speaker on/off Setup . . . . . . . . . . . . . . . . . . . . .29

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . . . .30

TIME Menu

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . .31

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . .32

TV Turn Off Time Setup . . . . . . . . . . . . . . . . . . . . .33

TV Turn On Time Setup . . . . . . . . . . . . . . . . . . . . . .34

Sleep Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . .35

Auto off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

OPTION Menu

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . . . .37

Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Caption Option Menu . . . . . . . . . . . . . . . . . . . . . . .40

On-Screen Menu Languages . . . . . . . . . . . . . . . . . . .41

Velocity Modulation . . . . . . . . . . . . . . . . . . . . . . . .42

Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Cinema 3:2 Mode Setup . . . . . . . . . . . . . . . . . . . . .43

EZ Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

LOCK Menu

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .45-46

Step 3. Miscellaneous

Programming the Remote . . . . . . . . . . . . . . . . . . . . .47

Programming Codes . . . . . . . . . . . . . . . . . . . . . .48-50

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .51-52

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .53-54

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55-56

Product Specifications . . . . . . . . . . . . . . . . . . . . . .57

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Note: Design and specifications are subject to change without prior notice.

PAGE 6

Front Panel Controls

power

Standby indicator (Illuminates brightly when the TV is

in standby mode. Dims when the TV is switched on.)

Remote control sensor

TV/VIDEO

menu

vol left/ right

Volume(

G) button increases the sound level and vol-

ume(

F) button decreases the sound level.

ch (Channel) up / down

1

2

3

4

These buttons work just as they do on your

remote control.

5

6

7

TV/VIDEO

MENU

VOL

CH

1

2

4

3

6

7

5

- Here shown may be somewhat different from your TV.

PAGE 7

Rear Connections Panel

Mini glossary

JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are color-

coded.

SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO

P

B

Y

L

R

IN1

IN2

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω

INPUT

IN3

S-Video In

A connection available

with some high-end

equipment that provides

even better picture

quality for Video 1, 2.

RF Connectors:

Antenna Input,

Used to connect

cable or antenna sig-

nals to the television,

either directly or

through your cable

box.

Video 1, 2 and 3 Inputs

Connects the video signals

from various types of

equipment.

Y, P

B, PR

DVD Component Video and HD

Component Video

Some top-of-the-line DVD players use

what is called “component video,” for

extremely accurate picture reproduc-

tion. Refer to your DVD manual for

further information.

- Connecting external equipment to your TV.

- Here shown may be somewhat different from your TV.

Left/Right Audio

Used for stereo sound

from various types of

equipment.

Component Left/Right

Audio

Used for stereo sound from

various types of equipment.

HDMI/DVI Input

Used to connect

from a DTV source.

Digital Audio

Output Optical

Connects to external

audio equipment

like a home theater

system.

Digital Audio Input

Optical

Connects to digital

audio from various

types of equipment.

PAGE 8

Front Connections Panel

Front A/V Panel

S-VIDEO

VIDEO IN

L/MONO

AUDIO

R

FRONT VIDEO

There are four jacks on the lower-right front

front of your TV that make connecting

Audio/Video devices like video games and

camcorders very simple.

The jacks are like those found on the back

jack connection panel. This means that most

equipment that connects to those types of

jacks on the rear jackpack, may be connected

to the Front connection panel (Front Video).

To use the Front jacks as the signal source,

select them using Main input menu as

described on page 23. They will be named

“Front Video” in the Main input menu.

Left/Right Audio

Used for stereo sound

from various types of

equipment.

Video in

Connects the video

signals from any

piece of equipment.

S-Video

A connection available on some very

high-end equipment that provides

better picture quality than video

input.

When you select Front video or

Front S-Video, the Front Audio

inputs are automatically selected

as well.

Do not connect to both Video and

S-Video at the same time.

Connect either Video or S-Video

only.

Mini glossary

A/V CABLES Audio/Video cables. Three cable connector—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo

playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video (picture) and/or audio (sound) (VCR, DVD, cable box, or television).

PAGE 9

Antenna / Cable Service Hookup

1

Connect an antenna and/or cable service to

your TV as shown.

Turn to page 19 to do a channel search

with EZ Scan.

For best signal reception, it is recommended to have your Antenna professionally adjusted.

2

If you receive your RF signal through an

antenna that is several years old and con-

nects with two small prongs, you will need to

purchase a 300 to 75 ohm adapter. It should

be available from your local

electronics dealer.

We recommend using a 75 ohm cable for

your antenna connection in order to prevent

interference.

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

ANTENNA

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

+75 Ω

Antenna

Cable TV

Wall jack

RF coaxial wire

(75 ohm)

RF coaxial wire

(75 ohm)

Mini glossary

TV OVER-THE-AIR SIGNALS DTV DIGITAL OVER-THE-AIR SIGNALS

CATV CABLE SIGNALS CADTV DIGITAL CABLE SIGNALS

Combined signals

TV/CATV/DTV Over-the-air, cable, and digital over-the-air signals

TV/CATV/CADTV Over-the-air, cable, and digital cable signals

CAUTION : If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches. The TV will let

you know when the analog, cable, and digital channel scans are complete.

PAGE 10

Cable Box Connections

If you’re using a cable box, leave the TV on

channel 3 or 4 and use your cable box to

change channels.

Locate the output jack on the back of

your cable box. Connect this to the Cable

jack on the back of your TV.

Or find the composite video and audio

jacks on the back of your cable box, and

connect them following the instructions

provided with your equipment.

This can be combined with any other

equipment you may want to hook up.

1

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

IN1

IN2

AUDIO

PR

PB

Y

L

R

AUDIO

+75 Ω

In

Output

Switch

Out

Audio

TV

VCR

L

R

Video

3 4

S-VIDEO

INPUT

IN3

RF coaxial wire

(75 ohm)

Cable box

Cable TV Wall

jack panel

PAGE 11

VCR Connections

1

Locate the Cable jack on the back

of your TV. Connect this to out

jack on the back of your VCR.

Or find the composite video and

audio jacks on the back of your

VCR, and connect them following

the instructions provided with

your equipment.

You may connect either the com-

posite video or the S-Video cables

to your TV. (Do not connect BOTH

the composite and the S- Video

cables. In the event that you con-

nect both composite and the S-

Video cables, only the S-Video will

work.)

To hear stereo sound from cable or your VCR,

you will need to connect A/V cables as well as

the wire that runs from the VCR to your TV.

If you want to receive your signals on Channel

3 or 4, locate the Out to TV jack on your VCR.

Connect a cable from the Out to TV jack to the

Antenna jack on the back of your TV.

In

Out

Audio

L

R

Video

3 4

S-Video

Output

Switch

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

IN1

IN2

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω

S-VIDEO

INPUT

IN3

RF coaxial wire

(75 ohm)

A/V cables

not included

with TV

or

VCR

Back AV panel

Cable TV Wall

jack panel

Antenna

Round wire

(75 ohm)

PAGE 12

DVD Player

Mini glossary

COMPONENT VIDEO Some video equipment uses three separate lines (Y, P

B, PR) to more precisely reproduce images. Your manual will explain how

this relates to your equipment.

1

2

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO

P

B

Y

L

R

IN1

IN2

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω

INPUT

Audio

L R

S-Video

IN3

Component input jacks

on the TV

Y

PB

PR

Video output jacks

of DVD player

Y

Pb

B-Y

Cb

PB

Pr

R-Y

Cr

P

R

• Component Input ports

You can get better picture quality if you

connect a DVD player using the component

input ports as shown below.

A/V cables

not included

with TV

DVD player

Back AV panel

or

Back AV panel

Find the component or S-Video

jacks for video connections,

depending on your DVD connec-

tors. Then make the correspond-

ing audio connections. See the

diagram for either set up.

You may connect either the

composite video or the S-Video

cables to your TV. Do not con-

nect both the composite and

the S-Video.

Some high-end DVD players use

a picture reproduction system

called “component video.” If

your DVD player has component

output, use the connectors

marked “Component 1 or 2” on

the jack panel. Please refer to

your DVD manual for proper

installation.

DVD/DTV INPUT

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

AUDIO

P

R

PB

Y

L

R

AUDIO

Audio

L R

Digital Audio

Optical

Component Video

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

ANTENNA

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

+75 Ω

DVD player

A/V cables

not included

with TV

PAGE 13

Set-top box Hookup

Find the audio and Y, PB, PR jacks or

HDMI/DVI output port on the back of

your set-top box and connect them fol-

lowing the instructions provided with

your equipment.

Connect these cables to your TV as

shown.

1

2

Digital Audio

Optical Output

Audio

L R

Component Out

Y Pb Pr

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

DVD/DTV INPUT

ANTENNA

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω

Set-top Box

The DTV shows the sharpest picture in 720p/1080i mode.

1920x1080i

1280x720p

720x480p

HDMI/DVI

or

Component 1 (or 2) Input

Y PB PR

1920X1080i

1280X720p

720X480p

720X480i

or

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

Set-top Box

PAGE 14

Digital Audio Output

Connect one end of an optical cable to

the TV Digital Audio Optical Output port.

Connect the other end of the optical cable

to the digital audio optical input on the

audio equipment.

See the external audio equipment instruc-

tion manual for operation.

1

2

Digital Audio

Optical Input

CALIBRATION

DIGITAL

AUDIO OUTPUT

OPTICAL

ANTENNA

HDMI/DVI

DIGITAL

AUDIO INPUT

OPTICAL

(DVI)

+75 Ω

Send the TV’s audio out to external audio equipment (stereo system) via

the Digital Audio Output Optical port.

Caution: Do not look into the optical output

port. Looking at the laser beam may damage

your vision.

Digital Audio

Equipment

PAGE 15

HDMI

- HDMI

TM

, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."

- This DTV can receive the High-Definition Multimedia Interface(HDMI) or Input of Digital Visual Interface(DVI).

- This DTV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for DTV(480p, 720p, 1080i) modes.

- When you Connect with HDMI Source Devices (DVD Player or Set Top Box) supporting Auto HDMI function, automatically, support Plug & Play

and then set the HDMI Source Devices(1920 x 1080i). After reading in HDMI Source Devices using Display Data Channel(DDC) Protocol, EDID

stored in DTV is used. If HDMI Source Devices not supported Auto HDMI/DVI is been, the Resolution is setted, manually.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1920 x 1080i.

- When Source Devices have DVI Output Connector, you must connect audio with separated cable. (Refer to <How to connect>)

- The HDMI is not supported in 480i source.

How to connect

1. When Source Devices(DVD Player or Set Top Box) support HDMI.

- If Source Devices have HDMI Output Connector, Source Devices connect to DTV with HDMI Cable .(not supplied with the product).

- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1920 x 1080i. But if not, resolution divert

Manually Setting for reference Manual of Source Devices.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1920 x 1080i.

- Because HDMI sends Digital Video and Audio with one cable, need not especial Audio Cable for using HDMI Cable.

2. When Source Devices(DVD Player or Set Top Box) supports DVI.

- If Source Devices have DVI Output Connector, Source Devices connect to DTV with HDMI to DVI Cable (not supplied with the product).

- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1920 x 1080i. But if not, resolution divert

Manually Setting for reference Manual of Source Devices.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1920 x 1080i.

- In this case, Audio use other cable. When Source Devices have Fiber Optic Digital Audio Output Connector, Digital Audio DVI Input(DVI) of

DTV connect to Fiber Optic Digital Audio Cable (not supplied with the product) or when Source Devices have Analog Audio Output Connector,

RGB/DVI Audio Input of DTV connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.

How to use

1. Connect the HDMI Source Devices (DVD Player or Set Top Box) and the TV set.

2. Turn on the display by pressing the ON/OFF button on the TV set and HDMI Source Devices remote control.

3. Check the image on your TV set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI

Source Devices. If noise is present, change the HDMI Source Devices to another resolution, change the refresh rate or adjust the bright-

ness and contrast on the menu until the picture is clear.

Reference

Cable sample

HDMI Cable (not supplied with the product)

HDMI to DVI Cable (not supplied with the product)

PAGE 16

Remote Control Functions in TV Mode

1 2 3

4 5 6

7 8 9

0

TV

MODE

TV/VIDEO

POWER

VIDEO1

FRONT

HDMI

VCR

CABLE

DVD

SAT

MUTE

SURROUNDFREEZE SAP

RATIO

INFO

RECORD

STOP

PAUSE

REW

PLAY

FF

MENU EXIT

TIMER CC

SIGNAL

VOL

CH

FAV

EZ SOUND

EZ PIC

COMP2COMP1

VIDEO2

SKIP

DASH(-)

FLASHBK

FAV

Use to scroll the FAV channel

list.

MENU

Brings up the main menu

to the screen.

EXIT

Clears all on-screen displays

and returns to TV viewing

from any menu.

CC

Lets you select a closed caption

mode for displaying captioning

information when provided for

DTV/Analog signal.

EZ PIC

Adjusts the factory preset picture depending

on the viewing environment.

SAP

Selects MTS sound: Mono, Stereo,

and SAP in analog mode.

Change the audio language in

DTV mode.

SURROUND

Selects : Off, 3D EchoSound

System and SRS TruSurround

XT.

MUTE

Switches the Mute or the EZ mute.

Mute: The sound is off. EZ mute: Turns

the sound off, and displays the caption.

THUMBSTICK

(UP/DOWN/LEFT/RIGHT/ )

Allows you to navigate the on-screen menus

and to adjust the system settings and prefer-

ences, by moving to an option with

F G

and

selecting the highlighted option with .

VIDEO1

Selects the Video1 input source.

MODE

Selects the remote operating mode:

TV, VCR, Cable, DVD or Satellite.

Select other operating modes, for

the remote to operate external

devices.

COMP2

Selects the Component 2 input

source.

EZ SOUND

Selects the sound appropriate

for the program’s category.

FREEZE

Captures and freezes

the currently-viewed

picture.

RATIO

Changes the aspect ratio.

TV/VIDEO

Selects: Antenna, Cable, Video1,

Video2, Front video, Component 1-2

and HDMI/DVI input sources.

MODE INDICATOR

LIGHTS

Show active remote mode

every time any button is

pressed.

D

E

PAGE 17

Remote Control Functions in TV Mode

1 2 3

4 5 6

7 8 9

0

TV

MODE

TV/VIDEO

POWER

VIDEO1

FRONT

HDMI

VCR

CABLE

DVD

SAT

MUTE

SURROUNDFREEZE SAP

RATIO

INFO

RECORD

STOP

PAUSE

REW

PLAY

FF

MENU EXIT

TIMER CC

SIGNAL

VOL

CH

FAV

EZ SOUND

EZ PIC

COMP2COMP1

VIDEO2

SKIP

DASH(-)

FLASHBK

POWER

Turns your TV or any other

programmed equipment on or

off, depending on mode.

CHANNEL UP/DOWN

Scrolls through available channels

present in EZ Scan memory.

NUMBER KEYPAD

For direct channel selection and

programming functions.

ENTER

When in the menu system and

other on-screen displays,

selects highlighted options.

RECORD, PAUSE, REW, FFWD,

PLAY, STOP

Control the functions on your VCR.

VOLUME UP/DOWN

Increases/decreases the sound level.

INFO

When you watch the TV, dis-

plays information on top of the

screen. Not available in

Component 1-2 and HDMI/DVI.

SKIP LEFT/RIGHT

Playing CDs: Selects songs.

Playing DVDs: Selects movie

chapters.

COMP1

Selects the Component 1 input

source.

HDMI

Selects the HDMI input source.

DASH(-)

Is used to enter a program num-

ber for multiple program channels

such as 2-1,2-2,etc.

FLASHBK

Tunes to the previous channel

viewed.

TIMER

Lets you select the amount of

time before your TV turns

itself off automatically.

SIGNAL

Displays the digital signal

strength.

FRONT

Selects the front video input source.

VIDEO2

Selects the Video2 input source.

PAGE 18

Turning the TV On

On-Screen Displays

This page describes your on-screen display and information banner options.

10

Mute

TV 2-0

MONO

10:00 AM

First, connect antenna cable and power cord correctly. At this moment, the TV switches to standby mode.

In standby mode to turn TV on, press the POWER, CH +/-, TV/VIDEO, FRONT or number buttons on the

remote control or TV/VIDEO or CH

D

/

E

on the TV.

Select the viewing source by using TV/VIDEO, COMP, FRONT or HDMI button on the remote control.

This TV is programmed to remember which mode it was last set to, even if you turn the TV off.

Note: See page 19 if you have not auto programmed the TV to receive channels in your local broadcast area.

When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

1

2

3

If you will be away on vacation, disconnect the power plug from the wall power outlet.

Volume

Volume level is displayed

while adjusting the sound.

Mute

Appears when

sound is muted.

Time

Appears when pressing the

enter button on remote control.

Channel Display

Displays current channel number.

Channel Label

Displays current

channel label.

PAGE 19

EZ Scan (Channel Search)

Use pages 9-14 to connect external

equipment to your TV. If you have done

so, plug in your TV to a standard 120V,

60Hz power outlet.

If you have done so, remove the back of

the remote and install in two AA batter-

ies. Make sure batteries are properly

installed (check the +/– symbols).

With the remote control in hand, press

the POWER button to turn your TV on.

1

2

3

Press the MENU button on the remote control,

then use the UP/DOWN arrow button to select

the SETUP menu.

Press the RIGHT arrow button to access the

SETUP menu.

Press ENTER button to begin the channel

search. Note: Allow EZ Scan to complete the

channel search cycle for Air (TV->CATV->DTV),

Cable (TV->CATV->CADTV) etc.

4

5

6

Automatically finds all channels available

through antenna or cable inputs, and stores

them in memory on the channel list.

back of

remote

1 2 3

4 5 6

7 8 9

0

TV

MODE

TV/VIDEO

POWER

VIDEO1

FRONT

HDMI

VCR

CABLE

DVD

SAT

MUTE

SURROUNDFREEZE SAP

RATIO

INFO

RECORD

STOP

PAUSE

REW

PLAY

FF

MENU EXIT

TIMER CC

SIGNAL

VOL

CH

FAV

EZ SOUND

EZ PIC

COMP2COMP1

VIDEO2

SKIP

DASH(-)

FLASHBK

4

6

3

Run EZ Scan again after any

Antenna/Cable connection changes.

4

5

PAGE 20

Channel Edit

Create two different types of channel lists in memory: “Custom

list” and “Favorite channel list” from the default channel list

made in the EZ scan menu.

A custom list can be created by toggling each channel on or off

with the (Enter) key. Once a channel is highlighted, you will be

able to see whether the channel is currently added or deleted by

referring to the small window at the top-left corner of the screen.

You can create your own favorite channel list with up to 20 chan-

nels.

Use the FAV button on the remote control when a channel is high-

lighted, to add or delete the channel in the favorite channel list.

Press the MENU button on the remote

control, then use the UP/DOWN arrow

button to select the SETUP menu.

Press the RIGHT arrow button to access

the SETUP menu.

Use the UP/DOWN arrow button to select

Ch.Edit and then press the RIGHT arrow

button.

You will now see a screen filled with

channel numbers and a preview picture.

Use the UP/DOWN and LEFT/RIGHT arrow

button to select a channel, then use

the button to add or delete it. Press

FAV to add the channel to the Fav List.

Press EXIT button to return to TV viewing

or press MENU button to return to the

previous menu.

3

4

5

2

1

1 2 3

4 5 6

7 8 9

0

TV

MODE

TV/VIDEO

POWER

VIDEO1

FRONT

HDMI

VCR

CABLE

DVD

SAT

MUTE

SURROUNDFREEZE SAP

RATIO

INFO

RECORD

STOP

PAUSE

REW

PLAY

FF

MENU EXIT

TIMER CC

SIGNAL

VOL

CH

FAV

EZ SOUND

EZ PIC

COMP2COMP1

VIDEO2

SKIP

DASH(-)

FLASHBK

1/5

4

5

4

2/3/4

1/3/4

4

CATV is available for 1-135 channel.

Page is loading ...

LG Electronics 30FZ1DC User manual

This manual is also suitable for

LG Electronics 30FZ1DC User manual

Related papers

Other documents