ICP MSM-508 User manual

Brand: ICP

Model: MSM-508

Category: Network switches

Type: User manual

This manual is also suitable for

Release No. : 0804-V1

Managed Switch Console Manual

Industrial Managed Ethernet Switch

Version 1.1

This document applied to models of

MSM-508,MSM-508FC/FCS/FT

Release No. : 0804-V1

CONTENTS

CONTENTS 2

Managed Switch 1

RS-232 & Telnet Console Operation 1

Console Connection........................................................................................2

Console Command.........................................................................................4

▓ ? [COMMAND] 4

▓ REBOOT／RESET 4

▓ DEFAULT 5

▓ IP 5

▓ MASK 6

▓ GATEWAY 6

▓ MAC 6

▓ NETID [id number] 7

▓ LMASK [mask value] 8

▓ CMASK [mask value] 9

▓ SMASK [mask value] 9

▓ LVALUE 10

▓ CMASK 10

▓ SMASK 11

▓ HMIVALUE [value1] [value2] 11

▓ RTIME [time] 12

▓ FTIME [time] 13

▓ MTIME [time] 13

▓ HTIME [time] 14

▓ COM1 [baud rate][data bit][parity][stop bit] 15

▓ COM2 [baud rate][data bit][parity][stop bit] 16

▓ RING [pair][enable|disable] 16

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 1

 Console Connection

 Console Command

Managed Switch

RS-232 & Telnet Console Operation

ICPDAS Managed Switch provides three access

methods, RS-232, Telnet and HTTP, to configure

the Switch functions. This Manual will guide you

how to use the RS-232 and Telnet to access

Managed Switch console.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 2

1. Console Connection





 RS-232 Connection

ICPDAS RS Series Switch is shipped with a 9-pin Female D-sub & RJ-45 cable

(CA-090510)，please use this cable to connect Switch’s RS232 port with PC’s COM port.

You can connect to Switch console by using windows Terminal Emulator,

Baud Rate : 115200

Data Bits : 8

Parity : none

Stop Bit : 1

Otherwise, you can download our free Console Emulator from RS Series Switch download

page:

http://www.icpdas.com/products/Switch/industrial/software.htm





 Telnet Connection

Before using telnet to access console, please mask sure the PC host and Managed Switch are

on the same subnet.

Factory default:

IP Address : 192.168.255.1

Gateway : 192.168.0.1

Mask : 255.255.0.0

Otherwise, you have to change the network setting through the RS-232 connection.

STEP 1

Click windows [Start] 



 [Run]

Type the Telnet command and switch’s IP address.

EX: telnet 192.168.255.1

STEP 2

If connection succeeds, the login prompt will appear.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 3

By factory default setting, both the account and password are Admin.

Only one telnet connection is accepted at the same time.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 4

2. Console Command

▓

▓▓

▓ ? [COMMAND]

Description

Both “help” and “?” display a list of available commands, if parameter is not specified.

The [command] parameter is used to see detail information for a specific command

Parameters

Parameter

Description

command

Please provide the name of the command that you want detail information about.

Example

▓

▓▓

▓ REBOOT／

／／

／RESET

Description

The reset command will initiate Ring Switch a self-restart. All current setting values remain

intact.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 5

▓

▓▓

▓ DEFAULT

Description

The default command will restore all settings to factory default values.

Current factory default values are as follow:

COM1:baudrate 115200,8bit,none patity check, 1 stopbit

COM2:baudrate 115200,8bit,none patity check, 1 stopbit

link mask:0

communication mask:0x1f

status mask:0x3

netid:1

mac: factory-set unique MAC address

ip:192.168.255.1

mask:255.255.255.0

Example

▓

▓▓

▓ IP

Description

If no IP address is specified, the “ip” command will display current IP address. To assign an

IP address for TCP/IP, please input IP address in the form of “ip1.ip2.ip3.ip4” (each field

contains a value in the range 0 – 255).

Example

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 6

▓

▓▓

▓ MASK

Description

If no mask address is specified, the “mask” command will display current mask address.

To assign a mask address for TCP/IP, please input mask address in the form of

“m1.m2.m3.m4” (each field contains a value in the range 0 – 255).

Example

▓

▓▓

▓ GATEWAY

Description

If no gateway IP address is specified, the “gateway” command will display current gateway

address. Note that if there exits a check sum error, an error message will alert. To assign a

gateway address for TCP/IP, please input gateway IP address in the form of

“ip1.ip2.ip3.ip4” (each field contains a value in the range 0 – 255).

Example

▓

▓▓

▓ MAC

Description

If no MAC address is specified, the “mac” command will display current MAC address. To

assign a MAC address for Ethernet, please input MAC address in the form of

“e1:e2:e3:e4:e5:e6”.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 7

Example

Each Switch is shipped from the factory with a unique MAC address, and the value is

labeled on the Switch case. DO NOT change this address unless you have a good

reason to do so.

▓

▓▓

▓ NETID [id number]

Description

If Net ID of Modbus is not specified, the “netid” command will display current ID number of

Modbus. The command parameter [id number] is used to assign a specific ID number for

Modbus Net ID.

Parameters

Parameter Description

id number Provides the ID number that you want to set up for Modbus Net ID.

Example

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 8

▓

▓▓

▓ LMASK [mask value]

Description

This command enables you to configure relay output activation status when there is link

loss occurring on port(s). The ports are corresponding to the 8 mask bits, bit 0 corresponds

to port 1, etc.

TABLE 1: Bits mapping Table

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Port 8

Port 7

Port 6

Port 5

Port 4

Port 3

Port 2

Port 1

1 on

0 off

If the mask bit of that port(s) is specified by being set up as 1, when there is a link loss

occurring on that port(s), relay output will be activated. The mask value is in hexadecimal

format that represents the 8 bits corresponding binary numbers, it can be either in the form

of initiating “0X” plus a suffix of the hexadecimal number or eliminating “0X”; simply the

hexadecimal number itself. If a mask value is not specified, the “lmask” command will

display previous assigned mask value.

Parameters

Parameter Description

mask value Provides the mask value that you want to specify to configure

status of relay when link loss occurs

Example

lmask 0x2d

Set Relay active if link lose on Port 1, 3, 4, or Port 6.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 9

▓

▓▓

▓ CMASK [mask value]

Description

This command enables you to configure relay output activation status when there is

communication loss occurring on port(s). The ports are corresponding to the 8 mask bits,

bit 0 corresponds to port 1, etc.

The bits mapping please refer to TABLE 1. (LMASK command)

Example

cmask 0x1a

Set Relay active if communication lose on Port 2, 4, or port 6.

▓

▓▓

▓ SMASK [mask value]

Description

This command enables you to configure relay output activation status when there is power

fail occurring on power 1 or power 2, or when the switch is being selected as the master

switch.

Bit 0 corresponds to Power1, bit 1 corresponds to Power 2 and bit 3 corresponds to master

switch indicator. If the mask bit of that power(s)(bit 0 and bit 1) or master switch indicator

(bit 2) is specified by being set up as 1, when there is a power fail occurring on Power(s),

or when the switch is selected as master switch, the corresponding relay output will be

activated.

Parameters

Parameter Description

mask value Provides the mask value that you want to specify for the

communication loss relay output

Example

smask 0x3

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 10

Set Relay active if Power 1 or Power 2 fail

▓

▓▓

▓ LVALUE

Description

This command enables you to read link status showing by a hexadecimal number that

represents the 8 bits corresponding binary numbers. Bit 0 corresponds to port 1, etc. If

there is link loss occurring on port(s), the corresponding bit(s) will be set up as 1.

Example

Link loss occurring on port 2,3,4,5,6 and 8.

▓

▓▓

▓ CMASK

Description

This command enables you to read ring pair communication status showing by a

hexadecimal number that represents the 8 bits corresponding binary numbers. Bit 0

corresponds to port 1, etc.. If there is a communication loss occurring on port(s), the

corresponding bit(s) will be set up as 1.

Example

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 11

▓

▓▓

▓ SMASK

Description

This command enables you to read system status showing by a hexadecimal number that

represents the 8 bits corresponding binary numbers.

bit

Corresponding to: Description

Power 1 If there is a power fail occurring on Power 1, bit 0 will be

set as 1.

Power 2 If there is a power fail occurring on Power 2, bit 1 will be

set as 1.

Master Ring Switch

If his Switch is the master Ring Switch (the Master LED

indicator will be “on”) bit 2 will be set as 1.

Relay output status If the relay output is activated, bit 3 will be set as 1.

Example

Power2 fail occurring, and the Switch is the Master of the topology.

▓

▓▓

▓ HMIVALUE [value1] [value2]

Description

This command enables you to configure the Switch operation modes.

Parameters

Parameter

Description

Value 1 bit0 : set 1 to enable ring pair 1.

bit1 : set 1 to enable ring pair 2.

bit2 : set 1 to enable STP Protocol. otherwise is Cyber-Ring Protocol

bit3 : set 1 to force Switch as the Master of topology.

Value 2 Reserved.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 12

Example

▓

▓▓

▓ RTIME [time]

Description

Recovery time is the length of time it takes to return back to normal operation after an error

or other failure has occurred. This command enables you to set up the recovery time in

millisecond (ms).

Parameters

Parameter Description

time Provides the time interval(ms) that you want to set up as the

recovery time

Example

Return message: “recovery time X (Y) ms. ”

“X” ( switch value) indicates the rtime value set by console command,

“Y” (operating value) indicates the actual operating value.

Value can be specified only on Cyber-Ring Protocol Mode (refer to HMIVLAUE setting).

NOTE

Use the following function to calculate an adequate rtime:

rtime = [Round(0.3*(N+1))]*100 ms

N: number of switches

Example:

If there are 5 switches (including master switch), the adequate rtime will be:

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 13

[Round (0.3*(5+1))]*100 = Round (1.8) *100 =2*100 =200 ms

If the recovery time is not longer enough, the Master LED will keep on flashing to make

a warning.

▓

▓▓

▓ FTIME [time]

Description

This command enables you to set up the spanning tree bridge forward delay in

milliseconds (ms) . Forward delay is the time interval spent waiting to change a port from

its spanning tree pre-forwarding state to a forwarding state. This is necessary because

every bridge on the network should ensure no loop is formed before allowing the port to

forward packets.

Parameters

Parameter Description

time Provides the time interval(ms) that you want to set up as the forward time

Example

Return message: “forward delay X (Y) ms. ”

“X” ( switch value) indicates the ftime value set by console command,

“Y” (operating value) indicates the actual operating value.

Value can be specified only on STP Mode (refer to HMIVLAUE setting).

▓

▓▓

▓ MTIME [time]

Description

This command enables you to setup the spanning tree bridge maximum age in

milliseconds (ms) . Max age is the maximum time a bridge waits without receiving

spanning tree configuration messages before attempting a reconfiguration.

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 14

Parameters

Parameter Description

time Provides the time interval(ms) that you want to set up as the maximum time

Example

Return message: “max age time X (Y) ms. ”

“X” ( switch value) indicates the mtime value set by console command,

“Y” (operating value) indicates the actual operating value.

Value can be specified only on STP Mode (refer to HMIVLAUE setting).

▓

▓▓

▓ HTIME [time]

Description

This command enables you to set the spanning tree bridge hello time in millisecond (ms).

Hello time is the interval between transmissions of spanning tree configuration messages.

All bridges send configuration messages during reconfiguration to select the designated

root bridge (in this case, the switch port).

Parameters

Parameter

Description

time Provides the time interval(ms) that you want to set up as the hello time

Example

Return message: “hello time X (Y) ms. ”

“X” (switch value) indicates the htime value set by console command,

“Y” (operating value) indicates the actual operating value.

Value can be specified only on STP Mode (refer to HMIVLAUE setting).

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 15

▓

▓▓

▓

COM1 [baud rate][data bit][parity][stop bit]

Description

The first serial port

Com1 is assigned for RS232. This command enables you to set up the

transmission speed (baud rate),data bit (data bit), parity check type (parity) and stop bit

(stop bit).

The transmission speed parameter [baud rate] allows the following settings: 300, 600,

1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200. The port speed and device

speed must match.

The number of data bits can be 7 (for true ASCII) or 8 (for any kind of data, as this matches

the size of a byte),

The parity check code can be set to none (0), even (1), or odd (2). None (0) means that no

parity bit is sent at all. Even (1) means applying even parity check, each set of transmitted

bits must have an even number of set bits. Odd (2) means applying odd parity check, each

set of transmitted bits must have an odd number of set bits.

Stop bit is used in asynchronous communications to indicate the end of a piece of data.

Parameters

Parameter Description

baud rate Provides the baud rate (300 or 600 or 1200 or 2400 or 4800 or 9600 or 19200

or 38400 or 57600 or 115200)for your usage, default value is 115200

data bit Provides the data bit value(7 or 8), default value is 8

parity Provides the parity check type, none

(0) , even (1), odd (2):, default value is 0.

stop bit Provides the stop bit (1 or 2), default value is 1.

Example

Industrial Redundant Ring Switch – Managed Switch Console Manual

Release No. : 0804-V1 16

▓

▓▓

▓

COM2 [baud rate][data bit][parity][stop bit]

Description

The second serial port

Com2 is assigned for RS485. This command enables you to set up

the transmission speed (baud rate),data bit (data bit), parity check type (parity) and stop bit

(stop bit).

Setting parameters are the same as COM1.

▓

▓▓

▓

RING [pair][enable|disable]

Description

1. Display ring setting

2. Enable／Disabled Ring Pair

Parameters

Parameter Description

pair Specify ring pair 1 or 2

enable|disable

Enable／Disabled Ring Pair .

Example

ICP MSM-508 User manual

Brand: ICP

Model: MSM-508

Category: Network switches

Type: User manual

This manual is also suitable for

Download PDF

report

ICP MSM-508 User manual

This manual is also suitable for

ICP MSM-508 User manual

Related papers

Other documents