LBL Lighting SU832BLLED827 Installation guide

LBL Lighting
Brand
LBL Lighting
Model
SU832BLLED827
Category
Signal cables
Type
Installation guide
1
Installation Instructions for
Interlace Suspensions
980INTERS
GP I :ENERAL RODUCT NFORMATION
These fixtures are intended to be installed utilizing
NEC compliant junction boxes.
This product is suitable for damp locations.
This product may be dimmed with a low-voltage electronic dimmer.
Suspension
1.1
SU767_, 832_, SU833_SU
Preparing the Canopy
1
1A
CROSSBAR
CANOPY
THUMB NUTTHUMB NUT
Remove the cross bar from the assembly by
unscrewing the two thumb nuts.
Mount the crossbar to the electrical box with the two
#8-32 screws.
CROSSBAR
ELECTRICAL
BOX
#8-32 SCREW #8-32 SCREW
1B
2
2 2
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
2
Install the Fixture
2A
CABLE
CLUTCH
AIRCRAFT
CABLE
STRAIN RELIEF
COAXIAL CORD
4
SET
SCREW
5
Place the fixture on a level surface.
Feed the aircraft cables through the cable clutches in
the canopy.
Evenly pull the aircraft cables up through the canopy to
raise the fixture to the desired length.
Ensure that the canopy is level, then cut off the excess
aircraft cable leaving enough for fine leveling later.
If necessary loosen the set screw in the strain relief and
feed the coaxial cord from the fixture into the strain
relief.
21
2
2
2
3
2
4
NOTE: The coaxial cord does not support the fixture.
For a casual “lazy cord” look, cut or leave the coaxial
cord several inches longer that the drop height of the
fixture.
Once the desired look is determined, tighten the set
screw on the strain relief.
26
2B
CORD
5
2
2
If shortening of the coaxial cords is necessary, take
note of the wire connections between the driver wires
and the coaxial cable (center conductor wire and the
braided conductor), then remove the wire nuts.
7
Leave 6" behind for wire connections, cut off the excess
cord.
From the end of the cord, strip the insulation 4" using a
sharp knife. Make sure not to nick the braided
conductor and center conductor wire.
Without nicking the center wire conductor, make a
1/4” cut at the base of the exposed braided conductor
and pull the center conductor wire out. Make sure not
to further damage the braided conductor while
doing so.
Strip the end of the center conductor wire and
reconnect the coaxial cable to it’s original connections
using the wire nuts.
8
9
2
5
2C
7
7
DRIVER WIRE
BRAIDED
CONDUCTOR
CENTER CONDUCTOR
WIRE
2D
10
11
9
10
11
CENTER CONDUCTOR
WIRE
BRAIDED CONDUCTOR
COAXIAL CORD
COAXIAL
CORD
CANOPY
3
Connect the driver and the crossbar ground wire to a
suitable ground in accordance with local electrical
codes.
Connect the white driver wire to the neutral power line
wire.
Connect the black driver wire to the hot power line
wire.
12
2E
12
Place all wires, wire nut connections, driver, and the
secondary strain relief properly inside the canopy.
Install the canopy onto to crossbar as secure it tightly
with the two thumb nuts.
NOTE: It is recommended that one person hold the
fixture while the electrician finishes the installation.
2F
THUMB NUT
THUMB NUT
11
12
1
Adjust the aircraft cables until the fixture is level; feed
the cable into the cable clutch to raise the fixture and
push in on the cable clutch nipple to release the cable
and lower the fixture.
Adjust the Suspension Cables (Optional)
CABLE
CLUTCH
CABLE
CLUTCH
1
3A
13
14
13
14
4
SAVETHESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2015 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LBL Lighting SU832BLLED827 Installation guide

LBL Lighting
Brand
LBL Lighting
Model
SU832BLLED827
Category
Signal cables
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents