BCM RX35Q User's Quick Start

Brand: BCM

Model: RX35Q

Type: User's Quick Start

BCM RX35Q is an ATX-form factor motherboard that supports LGA775 socket for Intel processors. It can accommodate up to 4GB of DDR3 memory and features two PCI-Express x16 slots for graphics cards. The motherboard also includes a variety of other expansion slots, including PCI-Express x1, PCI, and ISA. It has a Realtek ALC888 audio codec and a Marvell 88SE6111 Gigabit Ethernet controller. The back panel of the motherboard includes a PS/2 mouse and keyboard port, 4 USB 2.0 ports, 1 USB 3.0 port, an RJ-45 Ethernet port, a VGA port, a DVI port, and an HDMI port.

RX35Q

LGA775 Socket for Intel® 800/1066/1333MHz FSB

Core™ 2 Quad/ Core™ 2 Duo/

Pentium® 4/ Pentium® D/ Celeron® Processor 440

uATX Motherboard

User’s Quick Start Card

Version 1.00 http://www.bcmcom.com

Inspect the Package:

One RX35Q Motherboard

One 40-pin IDE cable

One SATA Cable

One SATA Power Cable

One I/O Shield

One Driver CD (Manual/Drivers)

One User’s Quick Start Card

Responsibility:

This manual is provided “As-Is” with no warranties of any kind, it will neither expressed or

implied, including, but not limited to the implied warranties or conditions of this product’s

fitness for any particular purpose. In no event shall we be liable for any loss of profits, loss of

business, loss of data, interruption of business, or indirect, special, incidental, or

consequential damages of any kind, even the possibility of such damages arising from any

defect or error in this manual or product. We reserve the right to modify and update the user

manual without prior notice.

WARNING: CMOS Battery Damage

Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium-Ion

coin cell (or equivalent) battery type to avoid risk of personal injury or physical damage to your

equipment. Always dispose of used batteries according to the manufacturer’s instructions, or

as required by the local ordinance (where applicable). The damage due to not following this

warning will void your motherboard’s manufacturer warranty.

Perchlorate Material- Special Handling May Apply.

See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

ATTENTION: Incorrect BIOS Setup

If you do not know how to handle BIOS setup or how to set it up properly, it is strongly

advisable that you do not modify any of the settings than otherwise instructed in the User’s

Quick Start Card. Even a seemingly small incorrect adjustment or modification in the BIOS

setup can render your system unstable or unusable. The incorrect BIOS setup is not covered

by your motherboard’s manufacturer warranty.

Additional Information:

Additional information on setting this board up can be found in the User’s Manual in the

provided CD-ROM. The Online User’s Manual and FAQ/Knowledge Base can be found on

our website by visiting our website: http://www.bcmcom.com. If your question is not

answered in our FAQ/Knowledge Base, visit our forums and post your messages or submit a

new FAQ through FAQ Submittal form for us to add your question in our FAQ with our

answer.

Motherboard Layout:

Back Panel:

Board Layout:

WARNING: Electrostatic Sensitive Device (ESD)

Static electricity can easily damage your motherboard and will void your motherboard

warranty. Keep the motherboard and other system components in their anti-static packaging

until you are ready to install them. Touch a grounded surface before you remove any system

component from its protective anti-static packaging. Unpacking and installation should be

done on a grounded, anti-static mat. The operator should be wearing an anti-static wristband,

grounded at the same points as the anti-static mat. During configuration and installation

touch a grounded surface frequently to discharge any static electrical charge that may have

built up in your body. Avoid touching the components when handling the motherboard or a

peripheral card. Handle the motherboard and peripheral cards either by the edges or by the

peripheral card case-mounting bracket.

WARNING: Misplaced Jumper Damage

Incorrect setting jumpers and connectors may lead to damage to your motherboard and will

void your motherboard warranty. Please pay special attention not to connect these headers

in wrong directions. DO NOT change ANY jumpers while the motherboard has the power!

Connectors, Jumpers, & Headers

Clear CMOS Jumper (JBAT1):

BIOS Flash Protection (JCI2)

ATX Power Connectors (24-Pin JPWR3, 4-Pin JPW1 ):

JPWR3

Pin Operation

1-2 BIOS Flash Protection Enabled

2-3 BIOS Flashable

All Open BIOS Flashable

Pin Signal Pin Signal

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS-ON#

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 PWROK 20 Res

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 GND

JPW1

Front Panel Connectors (JFP1, JFP2):

JFPI (Power SW, Reset SW, Power LED, Reset LED)

JFP2 (Power LED, External Speaker)

Fan Power Connectors (CPUFAN1, SYSFAN1):

Pin Signal

1 GND

2 GND

3 +12V

4 +12V

Pin Signal Description

1 HD_LED+ HD LED+

2 PWR/SLPLED+ Power LED+

3 HD_LED- HD LED-

4 PWR/SLPLED- Power LED-

5 RST_SW ResetSwitch

6 PWR_SW PowerSwitch

7 RST_SW ResetWitch

8 PWR_SW PowerSwitch

9 N.C. Not Connect

10 KEY KEY(no pin)

Pin Signal Description

1 GND Ground(LED-)

2 SPK Speaker

3 SLPLED SuspendLED+

4 NC No Connection

5 PWRLED PowerLED+

6 NC No Connection

7 KEY KEY(no pin)

8 SPK Speaker

SATA Ports

(Intel ICH9 SATA Ports (purple color): SATA1, SATA3, SATA4, SATA5)

(Marvell 88SE6111 SATA Port (blue color): SATA2)

IDE Connector (IDE1):

Floppy Drive Connector (FDD1):

Serial Port Connector (JCOM1):

Front 1394 Port Header (J1394_1):

Pin Signal Description

1 DCD Data Carry Datect

2 RxD Receive Data

3 TxD Transmit Data

4 DTR Data Terminal Ready

5 GND Ground

6 DSR Data Set Ready

7 RTS Request to Send

8 CTS Clear to Send

9 RI Ring Indicate

Pin Signal Pin Signal

1 TPA_1+ 2 TPA_1-

3 GROUND 4 GROUND

5 TPB_1+ 6 TPB_1-

7 CPWR_1 8 CPWR_1

9 KEY(no pin) 10 GROUND

Front USB Headers (JUSB1, JUSB2, JUSB3):

SPDIF Audio Connector (JSPD1):

Optical Drive Audio Connector (JCD_IN1):

Front Panel Audio Connector (JAUD1):

Chassis Intrusion Connector (JCI1):

Pin Signal Pin Signal

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 GND 8 GND

9 KEY(no pin) 10 N.C.

Pin Signal

1 VCC

2 SPDIF

3 GROUND

Pin Signal Description

1 AUD_MIC Front panel microphone input

2 AUD_GND Analog audio circuits Ground

3 AUD_MIC_BIAS Microphone Power

4 AUD_VCC Analog Audio Circuit 3V+

5 AUD_FPOUT_R Right Channel audio Signal to Front Panel

6 AUD_RET_R Right Channel Audio Signal Return From Front Panel

7 HP_ON Reserved for future use

8 KEY No pin

9 AUD_FPOUT_L Left Channel Audio Signal to Front Panel

10 AUD_RET_L Left Channel Audio Signal Return From Front Panel

BCM RX35Q User's Quick Start

BCM RX35Q User's Quick Start

BCM RX35Q User's Quick Start

Related papers

Other documents