Zebra AA18332-102 Owner's manual
- Category
- Label printers
- Type
- Owner's manual
AA18332-102 pg. 1 ZebraNet PS4000 Print System Safety Guide
Battery and Power Supply Safety
Caution • Use the Correct Zebra Power Source
Use the ZebraNet PS4000 Print System only with the Zebra
Technologies Model LA-24 Battery Pack and its charger power supply.
Follow the safety and usage guide provided with the LA-24 Battery
Pack.
Use of any power supply not approved specifically by Zebra for use
with the ZebraNet PS4000 Print System and the LA-24 Battery Pack
could cause damage to the server and will void the warranty.
Caution • Ensure Correct AC Compatibility
• Ensure that the ZebraNet PS4000 Print System battery charger power
supply is supplied with the proper AC power cord for the intended
country of use .
• The Charger Power Supply must be plugged into a properly grounded
AC outlet.
Important • Charger Power Supply Location
• Use care in locating the Charger Power Supply. Never locate the power
supply near any source of combustible material. Do not place it in loca-
tions where liquids or metallic objects may be dropped into the Power
Supply.
• Ensure the Charger Power Supply has adequate ventilation.
Important • Indoor Use Only
The Charger Power Supply shipped with the ZebraNet PS4000 Print
System is intended for indoor use only.
Important • Power Supply Maintenance
• Clean only with a dry or slightly damp, lint free cloth.
• Never operate a Charger Power Supply that has been damaged in any
way.
• Do not disassemble the Charger Power Supply. There are no user ser-
viceable components inside.
Print System Safety
Caution • Locate the Print System Properly
• Locate the Print System where its installation will not interfere with
normal movement of personnel.
• Ensure that all cabling connecting the Print System and the power sup-
ply are properly secured so that they will not present a hazard to per-
sonnel movement.
• Do not disassemble the Print System. There are no user serviceable
components inside..
Important • Indoor Use Only
The ZebraNet PS4000 Print System is intended for indoor use only.
Important Safety and Regulatory Information
for the ZebraNet
®
PS4000 Print System
Keep this Guide readily accessible. It contains important
safety information.
continued
ZebraNet PS4000 Print System Safety Guide pg. 2 AA18332-102
Important • Use Only With Zebra Printers
The ZebraNet PS4000 Print System is intended for use only with Zebra
Model LP and TLP28xx series and Models R2844-Z and R402 desktop
printers. Use of this server with printers not specified by Zebra may
result in unreliable performance. Zebra will not provide technical sup-
port for this product with use with third party printers
Always observe the Thermal Printer Safety Guidelines below..
Important • Use Only Zebra Cables
If using the Print System with an auxiliary printer only use the cables
specified by Zebra to connect this printer to the System and to supply
power to any printers or ancillary equipment. Failure to do so will void
the warranty and could cause damage to any equipment so connected.
Thermal Printer Safety
Important • Indoor Use Only
Any printer and/or any associated power supply which is a component
of the ZebraNet PS4000 Print System should never be operated in a
location where either one can get wet. Personal injury could result.
Important • Use Approved Media
Always use high-quality, approved labels and tags. If adhesive backed
labels are used that DO NOT lay flat on the backing liner, the exposed
edges may stick to the label guides and rollers inside the printer, caus-
ing the label to peel off from the liner and jam the printer.
Caution • Static Discharge
The discharge of electrostatic energy that accumulates on the surface
of the human body or other surfaces can damage or destroy the print
head or electronic components used in this device. DO NOT TOUCH the
print head or the electronic components under the top cover.
Caution • Thermal Printing
The print head becomes hot while printing. To protect from damaging
the print head and risk of personal injury, avoid touching the print head.
Use only the cleaning pen to perform maintenance.
AA18332-102 pg. 3 ZebraNet PS4000 Print System Safety Guide
continued
Radio Regulatory Information
ZebraNet PS4000 Using the 802.11g Radio
The following section only applies when the 802.11g radio
(with FCC ID: I28MD-ZLAN11G) is installed in a ZebraNet PS4000 Print
System. The antenna used for this transmitter must not be co-located or
must not operate in conjunction with any other antenna.
Caution • The ZebraNet PS4000 Print System contains a Radio
Frequency transmitter. To ensure compliance with the FCC’s rules for
Radio Frequency Exposure a minimum separation distance of 8 inches
(20 cm) must be maintained between this device and all persons during
device operations. If this minimum distance cannot be maintained then
exposure to RF levels that exceed the FCC’s limits may result..
European Regulatory Information for this Radio
AT BE CY CZ DK
EE FI FR DE GR
HU IE IT LV LT
LU MT NL PL PT
SK SI ES SE GB
Note: -Member states in the EU with restrictive use for this device are crossed out!
This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/
EC. The following test methods have been applied in order to prove presumption of
compliance with the R&TTE Directive 1999/5/EC:
• EN55022:1998
European Emissions Standard
• EN 60950: 2000
Safety of Information Technology Equipment
• EN 300 328-2 V1.2.1 (2001-12)
Technical requirements for spread-spectrum radio equipment
• EN 301 489-17 V1.2.1 (2002-08)
EMC requirements for spread-spectrum radio equipment.
Important Notice:
This device is a portable RF printer intended
for commercial and industrial use in all EU
and EFTA member states except in France
where restrictive use applies.
This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office
use in all EU and EFTA member states, except in France where restrictive use applies.
The use of this frequency band in France is subject to restrictions. You may only use
channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those French
departments as listed in the table below where channels 1-13 (2412-2472 MHz) may be
used. For more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr
01
Ain 36
Indre
69 Rhone
02 Aisne 37 Indre et Loire 70 Haute Saone
03 Allier 39 Jura 71 Saone et Loire
05 Hautes Alpes 41 Loir et Cher 72 Sarthe
08 Ardennes 42 Loire 75 Paris
09 Ariege 45 Loiret 77 Seine et Marne
10 Aube 50 Manche 78 Yvelines
11 Aude 54 Meurthe et Moselle 79 Deux Sievres
12 Aveyron 55 Meuse 82 Tarn et Garonne
16 Charente 57 Moselle 84 Vaucluse
19 Correze 58 Nievre 86 Vienne
2A Corse Sud 59 Nord 88 Vosges
2B Haute Corse 60 Oise 89 Yonne
21 Cote dʼOr 61 Orne 90 Territoire de Belfort
24 Dordogne 63 Puy de Dome 91 Essonne
25 Doubs 64 Pyrenees Atlantique 92 Hauts de Seine
26 Drome 65 Hautes Pyrenees 93 Seine St Denis
27 Eure 66 Pyrenees Orientales 94 Val de Marne
32 Gers 67 Bas Rhin
35
Ille et Vilaine 68
Haute Rhin
Zebra Technologies International, LLC
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061.3109 USA
Phone: +1.847.634.6700 or +1.800.423.0422
Fax: +1.847.913.8766
Zebra Technologies Europe Limited
Zebra House
The Valley Centre, Gordon Road
High Wycombe, Buckinghamshire HP13 6EQ,
UK
Phone: +44.1494.472872
Fax: +44.1494.450103
AA18332-102 rev. 1
August, 2006
-
1
-
2
-
3
-
4
Zebra AA18332-102 Owner's manual
- Category
- Label printers
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
