Reely 1410409 Operating instructions

Brand: Reely

Model: 1410409

Category: Remote controlled toys

Type: Operating instructions

Operating Instructions

Pistol grip system „GT4 EVO“ 2,4 GHz

Item No. 1410409

Version 10/16

Table of Contents

Page

1. Introduction .......................................................................................................................................................... 4

2. Use in accordance with the intended purpose ..................................................................................................... 4

3. Product description .............................................................................................................................................. 5

4. Scope of delivery .................................................................................................................................................5

5. Explanation of symbols ........................................................................................................................................ 6

6. Safety notes .........................................................................................................................................................6

6.1 General information ..................................................................................................................................6

6.2 Operation ..................................................................................................................................................7

7. Safety notes regarding the LiPo battery pack ...................................................................................................... 8

8. Charging the LiPo battery pack ...........................................................................................................................9

9. Operating elements of the transmitter ...............................................................................................................10

10. Starting up the transmitter ................................................................................................................................. 11

10.1 Switching on the transmitter.................................................................................................................... 11

10.2 Checking and setting the digital trimming ............................................................................................... 11

11. Starting up the receiver ......................................................................................................................................13

11.1 Receiver connection ...............................................................................................................................13

11.2 Installing the receiver .............................................................................................................................. 15

11.3 Installing the servo .................................................................................................................................. 15

11.4 Binding function ......................................................................................................................................16

12. Connecting a rotation sensor .............................................................................................................................17

12.1 General Information ................................................................................................................................17

12.2 Temperature Sensor ...............................................................................................................................17

12.3 Voltage Sensor........................................................................................................................................17

12.4 Speed Sensor .........................................................................................................................................17

12.5 Sensor Connections................................................................................................................................18

 12.6 Conguration/DisplayoftheSensors....................................................................................................18

13. Checking the steering and drive function ...........................................................................................................19

13.1 Checking the steering function................................................................................................................19

13.2 Checking the drive function.....................................................................................................................20

14. Programming the remote control ......................................................................................................................... 21

14.1 Programming the remote control ............................................................................................................21

14.2 Symbol explanation.................................................................................................................................22

14.3 Operating the LC touchscreen display ....................................................................................................22

Page

15. Main menu settings ............................................................................................................................................23

15.1 Main menu settings .................................................................................................................................23

15.2 “Reverse” function...................................................................................................................................24

15.3 “End points” function ............................................................................................................................... 25

15.4 “Subtrims” function ..................................................................................................................................26

15.5 “Steering exponential” function ...............................................................................................................27

15.6 “Steering speed” function ........................................................................................................................27

15.7 “Steering mix” function ............................................................................................................................ 28

15.8 “Throttle neutral” function ........................................................................................................................29

15.9 “Throttle exponential” function ................................................................................................................30

15.10 “Throttle curve” function .......................................................................................................................... 30

15.11 “A.B.S.” function ......................................................................................................................................31

15.12 “Throttle speed” function ......................................................................................................................... 32

15.13 “Throttle middle position” function ........................................................................................................... 33

15.14 “Throttle idle up” function ........................................................................................................................33

15.15 “Engine cut” function ............................................................................................................................... 34

15.16 “Boat mode” function...............................................................................................................................34

15.17 “Brake mixing” function ...........................................................................................................................35

15.18 “Mixes” function.......................................................................................................................................35

 15.19 “Displayservos”function.........................................................................................................................37

15.20 “Race timer” function...............................................................................................................................37

15.21 “Keys function” function ..........................................................................................................................38

15.22 “Models” function ....................................................................................................................................39

15.23 “S.V.C.” function ...................................................................................................................................... 40

15.24 “RX setup” function .................................................................................................................................41

15.25 “Spectrum analyzer” function .................................................................................................................. 44

15.26 “System” function .................................................................................................................................... 45

15.27 “Warning Signals” function ...................................................................................................................... 47

15.28 “Change Grip Shell” function...................................................................................................................47

16. Maintenance and care .......................................................................................................................................48

17. Disposal ............................................................................................................................................................. 48

17.1 General information ................................................................................................................................48

17.2 Batteries and battery packs ....................................................................................................................48

18. Eliminating faults ................................................................................................................................................48

19. Technical data ....................................................................................................................................................50

19.1 Transmitter .............................................................................................................................................. 50

19.2 Receiver ..................................................................................................................................................50

20. Declarationofconformity(DOC) ........................................................................................................................50

1. Introduction

DearCustomer,

We thank you for purchasing this product.

Thisproductcorrespondstolegal,nationalandEuropeanrequirements.

Inordertoensurethatthisstatusismaintainedalongwiththesafeoperationoftheproduct,theusermustobserve

these operating instructions!

These operating instructions belong to this product. They contain important notes regarding the initial start

up and handling of the product. Pay attention to this information. It also applies when the product is passed

on to a third party.

 Forthisreason,keeptheseoperatinginstructionssafeforre-reading!

If there are any technical questions, please contact:

International: www.conrad.com/contact

United Kingdom: www.conrad-electronic.co.uk/contact

2. Use in accordance with the intended purpose

The4-channelremoteisintendedexclusivelyforprivateuseinmodelconstructionanddesignedwiththeoperating

timesassociatedwiththisuse.Thissystemisnotdesignedforindustrialuse,forexample,forcontrollingmachines

or systems.

Anyuseotherthantheonedescribedabovemayleadtodamagetotheproductwiththeassociatedrisks,forexamp-

le,short-circuiting,re,electricshocketc.Theremotecontrolsystemmaynotbetechnicallymodiedorconverted!

The safety notes must be observed!

Pay attention to all safety notes given in these operating instructions. These contain important information

regarding the handling of the product.

 You,andyoualone,areresponsibleforthesafeoperationofyourremotecontrolandyourmodel!

3. Product description

Withthe4-channelremotecontrolyouhavearadioremotecontrolsystemideallysuitedtomodelvehiclesormodel

boats. The two proportional control channels enable driving and steering functions to be controlled independently of

each other.

Inaddition, you havetwofurtherswitching channelavailable.Thesecanbe usedtooperatespecial functionsor

gears.

The ergonomically shaped housing sits comfortably in the hand and enables convenient operation of the transmitter

as well as safe control of the model.

WherenoBECspeedcontrollerisused,thereceiverpowersupplyrequires4mignonbatteries(e.g.itemno.:652507,

packof4,order1)andadditionallyamatchingbatteryboxwithon/offswitch.Alternatively,youcanalsoinsertarea-

dyconguredreceiverbattery(recommended).Youneedamatchingon/offswitchforthis.Formatchingaccessories,

see our catalogues or www.conrad.com.

4. Scope of delivery

• RemoteControlTransmitter

• Speedsensorwithmagnet

• Remotecontrolreceiver

• VoltageSensor

• Programmingplug

• Temperaturesensor

• USBcable

• Gripshell

• Adaptercableforsensors

• LiPorechargeablebattery

• Operatinginstructions

Up-to-date Operating Instructions:

1. Open www.conrad.com/downloads in a browser or scan the displayed QR

code.

2. Select document type and language and enter the item number into the search

eld.Aftersubmittingthequeryyoucandownloaddisplayedrecords.

5. Explanation of Symbols

 Thesymbolwiththeexclamationmarkdrawsyourattentiontoparticularriskswithregardtohandling,use

or operation.

The arrow symbol represents special tips and operating notes.

6. Safety notes

The warranty/guarantee is voided In the event of damages caused by not observing these operating

instructions. We accept no liability for subsequent damages!

We accept no liability for property damage or injuries caused by improper handling or by not ob-

serving the safety notes! In such instances, the warranty/guarantee is voided. Normal wear and tear

caused by operation and accidental damaged are not covered by the warranty and guarantee (e.g.

broken receiver antenna, broken receiver housing etc.).

DearCustomer,Thesesafetyinstructionsarenotjustdesignedtoprotecttheproduct,theyarealsoforyourown

safetyandthatofotherpeople.Forthisreason,pleasereadthischapterthroughverycarefullybeforestartingto

operate the product!

6.1 General information

Caution, important note!

 Whenoperatingamodel,propertydamageand/orinjuriesmaybecaused.

 Ensurethatyouaresufcientlycoveredbyyourinsurancefortheoperationofthemodel,e.g.bymeansof

liabilityinsurance.Ifyoualreadyhavealiabilityinsurance,checkwithyourinsurerbeforestartingtooperate

your model whether the operation of the model is covered or not.

• Forsafetyandauthorisationreasons,ownconversionsand/ormodicationstotheproductarenotpermitted.

• Theproductisnotatoyanditisnotsuitableforchildrenunder14yearsofage.

• Theproductmaynotbecomedamporwet.

• Alwaysswitchonthetransmitterrst,thenthereceiversystem.Otherwise,themotormaystartupuncontrolledwith

an electrically powered model. A motor that is already running may run uncontrolled to full throttle in a model with

combustionengine.Inbothcases,unintendedpropertydamageand/orinjurymayoccur.

• Donotleavepackagingmateriallyingaroundcarelessly.Thismaybecomeadangeroustoyforchildren.

• Beforeeachstartup,checkthefunctionalsafetyofyourmodelandtheremotecontrolsystem.Payattentionto

visibledamages,forexample,defectivepluggedconnectionsordamagedcables.Allmovingpartsshouldmove

easily,butshouldnotdisplayplayintheirbearings.

• Ifthereareanyquestionsthatcannotbeclariedwiththeassistanceoftheseoperatinginstructions,pleasecontact

us(forcontactinformation,seeChapter1)oranotherspecialist.

The operation and use of remote controlled models is something that must be learned! If you have never

remotelycontrolledamodel,startverycarefullyandfamiliariseyourselfwiththeresponsesofthemodelto

the remote control commands. Be patient!

6.2 Operation

• Ifyoudonothavesufcientknowledgeofthehandlingofremotelycontrolledmodels,pleaseconsultanexperienced

model operator or model construction club.

• Whenstartingup,alwaysswitchthetransmitteronrst.Thenyoumayswitchthereceiverinthemodelon.Other-

wise,themodelmayreactinanunpredictableway!Avoidattemptingto“point”thetipoftheantennaatthemodel.

• Beforeoperating,checkwiththemodelatastandstilltoensurewhetheritrespondsasexpectedtotheremote

control commands.

• Whenoperatingamodel,payattentiontoensurethatnobodypartsorobjectsarelocatedinthedangerzoneof

engines or other rotating drive parts.

• Improperoperation may cause serious injury orproperty damage!Alwaysensure directvisual contact withthe

model and do not operate it at night.

• Onlycontrolyourmodelwhenyourresponsesarenotinuenced.Ifyouaretired,orundertheinuenceofalcohol

ormedication,youmayreactincorrectly.

• Onlyoperateyourmodelinanareainwhichyoudonotendangerotherpeople,animalsorobjects.Operateonlyon

privatepremisesorareasspecicallysetasideforthispurpose.

• Intheeventofafault,immediatelyceaseoperatingyourmodelandeliminatethecauseofthefaultbeforeusingthe

model again.

• Donotoperateyourremotecontrolsysteminastorm,underhigh-voltagepowerlinesorinthevicinityofradio

masts.

• Alwayskeeptheremotecontrol(transmitter)switchedonaslongasthemodelisinoperation.Afterendingyour

modeluse,alwaysswitchtheengineoffrst,thenswitchoffthereceivingsystem.Thenyoumayswitchremote

control transmitter off.

• Protecttheremotecontrolsystemfromdampandheavysoiling.

• Donotexposethetransmittertodirectsunlightorgreatheatoveralongerperiodoftime.

• Ifthebatteryintheremotecontrolisweak,therangewillbereduced.Ifthereceiverbatteryisweak,themodelwill

notrespondcorrectlytotheremotecontrol.Inthiscase,stopoperatingimmediately!Rechargethebatterypack!

• Donottakeriskswhenoperatingtheproduct!Yourownsafetyandthatofyoursurroundingsdependuponyour

responsible handling of the model.

7. Safety notes regarding the LiPo battery pack

• TheLiPobatterypack(LithiumPolymer)isnotforusebychildren.

• TheLiPobatterymayneverbeshort-circuited,dismantledorthrownintore.Thereisariskofexplosion!

• OnlychargetheLiPobatterypackinthetransmitter,neveruseanotherchargertocharge.

• OperatethetransmitterusingthesuppliedLiPobatterypackonly.

• IftheLiPobatterypackdistortsduringcharging,interruptthechargingprocess.

• TheLiPobatterypackmaynotbeovercharged.Interruptthechargingprocessimmediatelyifitbecomestoohot

during charging. The temperature of the LiPo battery pack may not exceed 60 °C during charging.

• DefectiveorincorrectlyloadedLiPobatteriesmaycatchre.Intheeventofare,onlydousetheameswitha

chemicalreextinguisher,neverwithwateraswaterwouldpromotetheames.

• NeverchargetheLiPobatterypackunattended.

• Neverputthe transmitterclose toammable orignitable materialsto chargethe LiPo battery.Alwaysputiton

reproofunderground.

8. Charging the LiPo battery pack

 Insubsequentsectionsoftheinstructions,thenumbersinthetextreferalwaystotheneighbouringFigure

ortotheFigureswithinthesection.Cross-referencestootherFigureswillbespeciedalongwiththeappro-

priate Figure number.

TheLiPobattery packrequired fortheremote controlis generallyincludedin thescope ofdeliveryand mustbe

charged.

Caution, important note!

 ThesuppliedLiPobatterypackmayonlybechargedinthetransmitter.Neveruseanotherchargertocharge

the LiPo battery pack.

 ThechargingcurrentoftheLiPobatterypackmayexceed500mA,forthisreason,chargingconnectedto

the USB port of a computer is not permitted.

Inserting and charging the LiPo battery pack

Thelidofthebatterycompartment(14)islocatedonthe

underside of the transmitter. Press on the corrugated

surfaceandslidethelidoff.Then,inserttheLiPobattery

pack.Slidethebatterycompartmentlid(14)backoverthe

compartment. The lid must click audibly into place.

ConnectaMicro-USBcable(X)totheMicro-USBport(12)

ofthetransmitter.ConnecttheotherendoftheMicro-USB

cable(X) toapluggable powersupply witha USBport.

Only charge the supplied LiPo battery pack in the trans-

mitter,neveruseanotherbatterypack.

The LiPo battery pack is fully charged when the symbol

ofthestatusdisplayofthetransmitterbatterypack(see

Figure10,Number3)iscompletelygreenwhenthetrans-

mitter is switched on.

Status display for transmitter battery pack/receiver battery pack

Battery pack is being charged

Battery pack is fully charged

Figure 1

9. Operating elements of the transmitter

1 LC touchscreen display*

2 „TR1“buttonfordualratefunctionthrottle/brake

3 „TR4“ button for dual rate function steering

4 “TR5” button for channel 3

5 “SW1” button for channel 3

6 “SW2” button for channel 4

7 “POWER” to switch on and off

8 “SW3” button for the “A.B.S” function

9 “TR3”buttonforthetrimmingofaccelerator/brake

10 Control wheel for steering function

11 “TR2” button for the trimming of steering

* not illustrated; input pin inserted on the rear of the

display

12 Micro-USBconnection

13 Accelerator/brakelever

Figure 2

Figure 3

10. Starting up the transmitter

10.1 Switching on the transmitter

Fortestingpurposes,switchthetransmitteronusingtheOn/Offswitch(seeFigure2,Number7).Thedisplayismade

visiblebythebacklightingnow.Tosavebatterycapacity,thebacklightingisautomaticallydimmedafterawhile.The

backlighting can be activated again by touching the display. Brightness settings and setting of the time until dimming

ofthebacklightingareexplainedinchapter“SettingsintheMainMenu/System”.

Pushtheon/offswitchagaintodeactivatethetransmitter.Itmustbepushedforaboutthreeseconds.

 Ifthesetting“Systemsound”isactivatedinthe“System”menu,signalsoundsareoutputatmenuchange

andinput.Additionally,asoundisgeneratedwhenswitchingon/off.

10.2 Checking and setting the digital trimming

Before you can carry out setting work on your model or

start with the programming of your product, you must

ensure that the digital trimming for the steering and drive

functionissettothemiddleposition(0).

Middle position of the steering function

Usingthe“TR2”trimmingbuttonforthesteeringfunction,

setthemiddlepositionforthesteeringservo(ST).Todo

this,pressthe“TR2”trimmingbuttoneithertotheleftor

to the right in order to set the value to 0. If you hold down

thetrimmingbutton,thevaluewillbechangedconstantly.

Thevaluecanbeadjustedbetweenleftandrightatupto

120 steps each.

 Every shortoperation of theprogramming and settingbuttons is conrmedby an acoustic signal when

the“Systemsound”settingisactivated.Ifabuttonispushedforalongerduration,thevalueswillchange

continuallyandthetransmitterwillemitafastsequenceofsounds.

 Whenyouperformtrimming,a sub-menu willopen.Thedisplaywillshowtrimming forsteeringandthe

throttle/brakeleverinlargeformat.Whenendingtrimming,thisdisplaywillautomaticallyreturntothebasic

menu. The set trim value is also displayed here.

Figure 4

Middle position of the drive function

Usingthetrimmingbutton(TR3)forthedrivefunction,setthemiddlepositionforthegasservo(TH).Todothis,press

thetrimmingbutton(TR3)eithertotheleftortotherightinordertosetthevalueto0.Ifyouholddownthetrimming

button,thevaluewillbechangedconstantly.Thevaluecanbeadjustedbetweenleftandrightatupto120stepseach.

 Every shortoperation of theprogramming and settingbuttons is conrmedby an acoustic signal when

the“Systemsound”settingisactivated.Ifabuttonispushedforalongerduration,thevalueswillchange

continuallyandthetransmitterwillemitafastsequenceofsounds.

 Whenyouperformtrimming,a sub-menu willopen.Thedisplaywillshowtrimming forsteeringandthe

throttle/brakeleverinlargeformat.Whenendingtrimming,thisdisplaywillautomaticallyreturntothebasic

menu. The set trim value is also displayed here.

Also set the middle value precisely if you are using an electronic cruise control in place of a gas servo.

11. Starting up the receiver

11.1 Receiver connection

Thereceiver offersconnection optionsfor upto fourservos (CH1, CH2,CH3, CH4)and areceiver battery pack

(BIND/VCC).

Figure5ashowsaconnectionchartforamodelwithexternalreceiverpowersupply(gure5a,item1),asitiscom-

mon,e.g,foracombustionmodel.

Figure 5b shows a connection chart for an electrically powered model in which the speed controller has an integrated

BEC(BECisareceiverpowersupplyintegratedintothespeedcontroller).Thedrivingbattery(gure5b,item1)is

connectedtothespeedcontroller(gure5b,item2)here.TheBECintegratedinthespeedcontrollersuppliesthe

entirereceiversystemwithpowerthroughtheconnectionoftheservoplugfromthespeedcontrollertoCH2.

IfthespeedcontrolleruseddoesnothaveanyintegratedBEC,thereceiversystemmustbeproducedwithanexternal

receiverpowersupply.Usegure5aasreference.Inthiscase,onlytheservoServo2(CH2)needstobereplaced

by the speed controller.

IfanelectronicspeedcontrollerwithintegratedBECisusedinamodel,noexternalpowersupplymustbe

connectedtothereceiver,sincethismaydestroythespeedcontroller.TheBECmaybedisconnectedfrom

thereceiversystemforuseofexternalreceiverpowersuppliesifyouseparatethemiddle,redwireatthe

servo plug of the speed controller and insulated it.

Ifnecessary,youcanconnectanadditionalservotoreceiveroutputCH3andCH4inadditiontothesteeringservo

onreceiveroutput“CH1”andthethrottleservo/speedcontrolleronreceiveroutput“CH2”.Theseservoscanbeused

for various additional functions.

Withaelectronicmodelwithamechanicaldriveregulator,abatteryboxoraseparatereceiverbatterypackisrequi-

red for the power supply of the receiver in all cases. The power supply connection mounted to the mechanical drive

regulatormaynotbeusedsincethevoltageattheplugof7.2V(fora6celldrivebattery)istoohighforthereceiver

and the connected servos.

Pay attention when connecting servos to always ensure the correct poling of the plug connector. The plugged contact

fortheimpulsecable(yellow,whiteororangeaccordingtomanufacturer)mustbeconnectedtotheinner(left)pin

contact.Thepluggedcontactfortheminuscable(blackorbrownaccordingtomanufacturer)mustbeconnectedto

theouter(right)pincontact.

Switchthetransmitteronandthenswitchthereceiveron.IftheBindingfunctioniscorrect,theredcontrolLEDonthe

receiver will light up. Check the correct functionality of the receiver and then switch it back off.

 IftheLEDsinthereceiverdonotlightuportheconnectedservosdonotreacttotheremotecontrolsignals,

the Binding function must be carried out. More information can be found in the later Chapter “Binding func-

tion”.

Example of the connection of a combustion models

Figure 5 a

Example of the connection of an electric model with an electronic cruise control and BEC switching

Figure 5 b

11.2 Installing the receiver

Theinstallationofthereceiverdiffersaccordingtothemodel.Forthisreason,observetherecommendationsmadeby

the model manufacturer with regard to installation.

Generallyspeaking,youshouldalwaystrytoinstallthereceiverinsuchawaythatitisoptimallyprotectedfromdust,

dirt,dampandvibrations.Double-sidedadhesivefoamorrubberringsaresuitableforsecuringthefoamwrapped

receiverrmlyinplace.

Thelast3centimetresoftheaerialwirearedeemedtheaerial.Theremainingpartonlyservestoextendtheaerial,

to place or position it in a model.

Installtheaerial(i.e.thelast3centimetres)withsuitableaids(e.g.theaerialtubefromthedelivery)sothatitpoints

from the RC box or model as vertically as possible.

Generally,thefollowingruleapplies:Thehighertheaerialprotrudesfromamodel,thesaferthereception.

 Theantennawireofthereceiverhasapreciselycalculatedlength.Forthisreason,theantennawiremay

notbecoiled,loopedorcut.Thereceiverrangewouldbestronglylimitedandthuswouldbeaconsiderable

safety risk.

11.3 Installing the servo

The installation of a servo is always dependant on the model being used. Precise information can be obtained from

the construction documents of the model.

Intheeventofstiffruddersandsteering,servosareunabletooperateintherequiredposition.Theyconsumeunne-

cessary power as a result and the model cannot be controlled cleanly.

Alwaysmounttheservoleverata90°angeltothesteeringrods.Withaservoleverdiagonaltothesteeringrods,the

steering or rudder movement in both steering directions are not of the same magnitude.

Pay attention before installing the servo lever for the drive and steering function to ensure that the trim func-

tionoftherelevantchannelissettothemiddleposition.Formoreinformation,consultthesection“Checking

and setting the digital trimming”.

 TheservoleversattheservosthatareconnectedtoCH3andCH4mustbeinstalledsothattheycannotrun

on block when switching from one end position to the other.

11.4 Binding function

In order for the transmitter and the receiver to communi-

catewitheachother,theymustbeboundusingthesame

digitalcoding.Whendelivered,thetransmitterandrecei-

ver are already coordinated and can be used immediately.

TherenewaloftheBindingfunctionis,primarily,

only necessary after switching a transmitter or receiver or

when eliminating faults.

ThetransmitterandreceiverarenotboundiftheLEDin

thereceiveronlyashesinspiteofthetransmitterbeing

on.

If the transmitter has lost the binding with the receiver due

toaninterference,orifyouwanttobindanewreceiverto

thetransmitter,proceedasdeclaredbelow.

Removeallservoplugs,aswellasanypresentexternalpowersupply,fromthereceiver(1).Connectthebinding

plug(short-circuitplug)tothereceiveronBIND/VCC(3).Connectareceiverbattery(2)toafreechannel(e.g.CH4).

Switchonthereceiverpowersupply.ThereceiverLEDashesveryfast.Switchonthetransmitternow.

Selectthemenu“RX-Setup”.Selectthefunction“Bindwithareceiver”inthismenu.ThetransmitterasksintheEng-

lishlanguageifyoureallywanttobindtoareceiver.Conrmwith“yes”.

BindingwassuccessfulifthereceiverLEDispermanentlylit.

Nowswitchoffthereceiverpowersupplyandremovethebindingplug.Onlynowcanallservosandanyexternal

power supply be connected again and the receiver be used.

Checkthecorrectfunctionoftheconnectedservos/speedcontrollersbeforeoperatingthemodelandperformarange

check.

 ThetransmittercanalsobeoperatedwiththereceiversoftheremotecontrolsystemsGT2,GT3andGT4.

However,telemetrywillnotbeavailablethen.

 Forbindingthereceiversnamed,thesubmenu“RFstd.”mustbeselectedinthemenu“RXsetup”and,

dependingonreceiverused,either“AFHDS”or“AFHDS2”mustbeselected.

Figure 6

12. Connecting a rotation sensor

12.1 Programming the Remote Control

Threesensors are includedin the deliveryof the remotecontrol that can record atemperature, a voltageand a

speed. Up to 15 sensors can be connected to the receiver in series and displayed in different constellations in the

transmitter.

12.2 Temperature sensor

Thetemperaturesensor“CTM01”canmeasure,e.g.,thetemperatureofaspeedbatteryintherangeof-40°Cto

+250°Candtransmitittothetransmitterbytelemetrics.Forthis,attachthetemperaturesensorthatisinstalledtothe

sensorhousinginasuitablelocation,e.g.witharubberbandoradhesivetape.

12.3 Voltage Sensor

Thevoltagesensor“CVT01”canmeasure,e.g.,thevoltageofaspeedbatteryintherangeof4.0Vto100.0Vand

transmitittothetransmitterbytelemetrics.Plugtheconnectioncable,whichisinstalledtothevoltagesensor,tothe

speedbatterywiththecorrectpolarity(e.g.tothebalancerconnection).Theredcablemustbeconnectedtotheplus,

the black to the minus pole of the rechargeable battery. Avoid short circuits and polarity reversal since this may cause

damage.

12.4 Speed Sensor

Thespeedsensor“CPD01”canmeasure,e.g.,thespeed

inthe range of 0 to60,000 U/min andtransmit itto the

transmitterbytelemetrics.Atthetransmitter,youcandis-

playthe speed of the drive wheel.Additionally, you can

displaythedistancedriven(menuitemodometer)and/or

thespeeddriven(menuitemSpeed)withthecorrespon-

ding settings at the transmitter.

Toinstallthespeedsensor,youneedtoattachamagnet

(gure7a,item3)totherotatingpart(e.g.awheelrim–

gure7a,item1)sothatthesensorofthespeedsensor

(g.7a,item2)canslidepastatadistanceoflessthan

orequalto2mm.

Assemblymaterialrequiredforthis(suitableglueforthe

magnet or, e.g., cable ties for the sensor attachment)

are not enclosed with the remote control and must be

purchased separately.

Figure 7a

12.5 Sensor Connections

Plugthecableofthedesiredsensor(1)intothe“SENS”

socketatthereceiver(2).

Installthesensorjustconnectedinyourmodelaccording

toitspurpose(e.g.measuringtemperatureofarecharge-

ablebattery)sothatnocablescangetintorotatingparts

of the drive.

After taken the transmitter and then the receiver into ope-

ration,theLEDinthesensorslightsupinadditiontothe

LEDinthereceiver.

Measurement and transmission to the transmitter is ac-

tivated.

Ifyouwanttouseseveralsensors(1+n)inyourmodelfor

measuringpurposesatthe sametime,connectthenew

sensor(s)simplytotherst(orpresent)sensor.

 Allsensorscanbedisplayedatthetransmitterinthemenu“RXsetup”,inthesubmenu“Displaysensors”.

Youcanhaveuptofoursensorsdisplayedinthemainmenuofthedisplay.Forthis,selectthesequence

andselectionofthesensorsinthesubmenu“choosesensor”.Displayorselectionofthedifferentsensors

is only possible with the transmitter and receiver activated.

12.6 Conguration / Display of the Sensors

Thesensorsconnectedtothemodelandthereceivercanbedisplayedinthemainmenu(i.e.thedisplaythatthat

showstheindicationafteractivationofthetransmitter).Uptofourdisplayscanbeselectedhere.Forinformationon

this,seethechapter“RXsetup”underitem“ChooseSensors”.

Alternatively,youcandisplayallvaluessubmittedbythetransmitter,includingalltheconnectedsensorsinthemenu

“RXsetup”inthefunction“Displaysensors”.

Forthis,observethenotesintheseoperatinginstructions,chapter“RXsetup”,“DisplaySensors”.

SENS

Figure 7b

13. Checking the steering and drive function

 Inordertoensurethatthemodeldoesnotdriveoffwhenyouarecheckingthesteeringanddrivefunction,

placethemodelchassisonasuitablebase(blockofwoodorsimilar).Thewheelsshouldbeabletoturn

freely.

13.1 Checking the steering function

 Alwayscarryoutdigitaltrimmingbeforecheckingthesteeringfunction.Formoreinformation,consultthe

section “Starting up the transmitter” in the Chapter “Checking and setting the digital trimming”.

Switch both the transmitter and the receiver on to carry out

the check. If everything has been connected and installed

correctly the steering should react to the rotation motions

of the control wheel.

When the control wheel is in the middle position, the

wheels should be pointing straight ahead.

If the wheels are at an angle although the control wheel

isinthemiddleposition,checktoseewhethertheservo

lever is at an angle to the steering rod.

Inthiscase,undotheservolever,andscrewitbackinto

place one “tooth” offset.

Further deviations in the wheel positions can be corrected

ifnecessarybyadjustingthesteeringrod.

Ifyousteertotheleft,thewheelsshouldturnleft.Ifyou

steertotheright,thewheelsshouldturnright.

If the control direction should react in precisely

the opposite way to the control direction on the

transmitter, this can easily be reprogrammed.

See the Chapters “Selecting the menu” and then

“Reverse”.

Figure 8

13.2 Checking the drive function

 Always carry out digital trimming before checking the drive function. For more information, consult the

section “Starting up the transmitter” in the Chapter “Checking and setting the digital trimming”.

When you pull the accelerator/brake lever for the drive

functionasfaraspossibleinthedirectionofthehandle,

the model should accelerate.

Whenyoupushtheaccelerator/brakeleverforthedrive

functionforwards,themodelshouldbebrakedorswitched

to reverse.

If the control direction should react in precisely the oppo-

sitewaytothecontroldirectiononthetransmitter,thiscan

easily be reprogrammed. See the Chapters “Selecting the

menu” and then “Reverse”.

After you have checked or set the correct drive and stee-

ringfunctions,rstswitchoffthereceiver,thenthetrans-

mitter.

Important!

 Foramodelwithacombustionengine,settherodsfortheexhaustandbrakesteeringinsuchawaythat

theaccelerator/brakeservoisnotlimitedmechanically.Thetrimmingregulatorforthedrivefunction(see

Figure2,Number11)mustbeinthemiddleposition.

 Fora modelwith an electronicdrive regulator, thevarious positions of the operatinglever forthe drive

functions(forwards,stop,reverse)mayneedtobeprogrammedintothedriveregulator.Additionalnotes

regarding this can be obtained from the documentation belonging to the drive regulator.

Figure 9

Page is loading ...

Reely 1410409 Operating instructions

Brand: Reely

Model: 1410409

Category: Remote controlled toys

Type: Operating instructions

Download PDF

report

Reely 1410409 Operating instructions

Reely 1410409 Operating instructions

Related papers

Other documents