Friax MPCA 20 C Genesis Installation guide

Installation Manual

MPC Genesis - Vintage

Les caractéristiques données dans cette fiche technique peuvent évoluer sans avis

préalable, avec les améliorations que "FRIAX Industrie" entend toujours apporter à

sa production.

GB-NT-MPCA-0218

R

INDUSTRIE

France

®

MPCA

Genesis - Vintage

MPCA

Genesis - Vintage

Emballage

MPCA

Genesis - Vintage

P

H

L

2

Contents of the package

Thank you for choosing a FRIAX's Monobloc system to control the aging of your wine.

Take the me to read this manual. It will help you understand the steps to install and adjust the MPC series.

What is a cellar Monobloc system FRIAX ?

The MPC serie is a refrigeraon system specially designed to keep the opmum temperature and humidity at

the aging of your wines. The system is composed of three essenals elements which are the evaporator, the

condenser unit and the regulaon box. These elements are interconnected by a refrigerant pipe and an

electrical connecon.

At the delivery, you must ﬁnd in your package, your Monobloc, the installaon manual and the accessories

describde on page 3. Check package to detect any damage on the carton. Note on the delivery of the carrier all

the observaons about the package condion, this could be useful in case of damage.

If in doubt contact your dealer.

When unpacking check that the material inside the package corresponds to the checklist on the box.

Safety

-Be sure to install the unit in a sheltered place.

-It is advisable to remove the device from its packaging with the help of someone.

-Connect the power supply once the enƟre installaƟon is complete.

Oﬀ pallet dimensions:

750 mm x 490 mm x 510 mm ( P x L x H)

MPCA

Genesis - Vintage

Données techniques

3

MPCA 20 MPCA 20 C

Cooling capacity +6°C 500 W 500 W

Cooling capacity +12°C 610 W 610 W

Voltage 230 V - 50Hz 230 V - 50 Hz

Current heaƟng mode -

Power consumpƟon 230 W / 1,2 A 230 W / 1.2 A

Airﬂow cellar side

1 m 1 m

Refrigerant R290 R290

nominal outside temperature

28°C 28°C

4 - 18 °C 4 - 18 °C

Weight 45 kg 49 kg

-

Current cooling mode 2,41 A 3,24 A

210 m3/h

Temperature seƫng range

Airﬂow outside

250 m3/h

Power cable lenght

Genesis & Vintage Genesis

Condensate evaporator tray

No Yes

MPCA

Genesis - Vintage

Accessories

Monobloc FRIAX comes with

- A box with wireless remote, table stand for remote control and two baeries

- A ﬂexible drain tube Ø 16 2m length

- A bag containing screws ﬁxing brackets on the air condioner, this leaﬂet and a ﬁng

20/27 for hose Ø 10 on Vintage versions

Outside

28°C

Cellar

12°C

Condenser

Evaporator

4

260

48 42

204

19243

567

198 75

285

43

25

350

25326

374 139

Evaporator air inlet

Regulation LED + synchronization button Power Supply

Condenseur air outlet

Evaporator air outlet

Condensor air inlet

Dimensions

MPCA

Genesis - Vintage

OperaƟng principal

MPCA

Genesis - Vintage

Installation

Position of the opening in the bottom of the cabinet

5

90 mini

285

75

43

5

13

260 23

199

75199

26023

285

60

MPCA

Genesis - Vintage

Installation

6

567

570 between cleat

60 mini

480 mini

11

60

90

MPCA

Genesis - Vintage

Installation

ConnecƟon of the drain

Only units not equipped with the KBEC opon (condensate evaporaon pan kit) must be

connected to a drain.

Connect the drain

• Connect the drain tube (Ø 16) to the end

of the elbow with the supplied collar.

7

MPCA

Genesis - Vintage

+

-

Wirless remote control

Power supply: 2 x 1.5V (AAA) provided

60

83

80

26

8

The remote control could be installed in any room. Its maximum range is 100m in a

completely open area. This distance could be extremly reduced by thickness of walls

and the locaon of the cellar. It is possible to ﬁx directly the remote to the unit by

using the screw holes on the MPC facade.

9

MPCA

Genesis - Vintage

Wireless remote

Configuration type

Key lock indicator

Crankcase heater indicator

Silent indicator (EC fan evaporator)

Heating indicator

Cooling indicator

Condenser temperature probe

Humidifier indicator (

VINTAGE model

)

Cellar temperature probe

Parameter number

Setup mode

Radio frequency signal

Temperature or humidity indicator (option)

Battery charge level indicator

°C / °F or humidity (%) unit indicator

Speed condensor fan

Speed evaporator fan

Time (12 AM/PM or 24 h)

existing if EC evaporator fan

existing if EC condenser fan

Minus for negatives values

Lighting control

%

1

23456789

10

11

12

14

15

13

18

17 16

OK

-

+

Menu key

Return

Navigation key

Start key

Stand by

Stop

Navigation key

Validation key

-Red : heating mode

-Green : cooling mode

-Flashing red : Alarm

19

20

21

22

12

13

14

15

16

17

18

19

20

21

22

1

2

3

4

5

6

7

8

9

10

11

10

MPCA

Genesis - Vintage

First start

Step I - Set the cellar fan speed

-For MPC 30 select the value * and conﬁrm.

-For MPC 48 select the value * and conﬁrm.

* For speed value, see the speciﬁc installaon instrucons when the appliance is installed outside the cave

(mounng OUT) and the evaporator is ducted.

Step II - StarƟng

Seng the

speed evapora-

tor fan cellar

Even if the screen

is blank Press

for 6 seconds

Change the

screens with

OK

conﬁrm with

-

+

Change the value with

or

Access to

menu

Parameters Display Handling

See below the value

set according to the

device

Login with

Shorten the waing

period ** hold

Start the unit with the

remote control

The unit starts in heang

or cooling mode. If the set

is idencal to the tempe-

rature of the cellar, the

screen shows no opera-

on.

The unit starts.

If the icons and

are ﬂashing the unit is in

standby mode.

Press

for 2 seconds

or

becomes xed

or

xed or ashing

** It is the preheating of the compressor crankcase heater which avoid any blow of liquid during the

rst start. It is preferable to respect this period until its completion

To exit the menu,

press

funcons Handling Views Remarks

Remarks

11

MPCA

Genesis - Vintage

Settings: temperature and humidity *

OK

Seng Handling Display Remarks

Adjust the tempe-

rature setpoints

and humidity

(Vintage Version)

Press

For 2 seconds Flashing

Flashing

Displays the current value

of the setpoint tempera-

ture

Displays the current value

of the set point humidity

(* Only on Vintage models)

Displays the value of

setpoint desired humidity

(* Only on Vintage models)

Displays the value of the

desired setpoint tempera-

ture

Returns to the display of

measured values in the

cellar

%

OK

conﬁrm with

OK

conﬁrm with

-

+

Change the value with

or

-

+

Change the value with

or

Step III - Set the cellar temperature and humidity

Restart the unit with the

remote control Resume in step II

Stop the unit with the

remote control

Press

for 6 seconds

funcons Handling Views Remarks

Step IV - Stop the unit

Red LED on unit. The air

condioner is stopped but

the funcon of compres-

sor protecon remains

acve RC**

** If the unit remains o for a long period of time, it is better to stop it this way. This will protect the

compressor when restarting

* Only on Vintage models

12

MPCA

Genesis - Vintage

User menu

funcons Handling Views Remarks

Display the tempera-

ture or humidity of the

cellar

Put the fan in the cellar

in silent mode

Exit silent mode

Press

Lock the keypad on the

remote control

Unlock the keypad on

the remote control

Pause the remote

screen

Out of standby screen

Stop the machine with

the remote

Start the unit with the

remote control

Flashing

Fixed

The display alternately

shows the value of the

temperature and humidity

(Only available on Vintage

model)

The fan switches to low

speed for 10 minutes

The fan returns to its

normal speed

Manipulaon buons no

longer possible to change

the sengs

Buons are accessible to

change the sengs

The screen turns oﬀ aer

a few seconds. The

appliance connues to

operate

The screen turns on and

displays the current values

Red LED on unit. The air

condioner stopped but

the compressor protecon

remains acve RC

(crankcase heater)

%

-

Press -

Then simultaneously

on

Then simultaneously

on

Press

Disappearing

Flashing

%

The unit starts.

If the lights and

are ﬂashing the unit is in

standby mode.

or

xed

defrost mode Hold

Starts a manual defrost in

addion to the automac

defrost all 7 hours

Press

for 2 seconds

Press

for 2 seconds

Press

for 2 seconds

Press

for 2 seconds

Press

for 6 seconds

Lighng control

Press

5 Seconds

+

Lighng on / oﬀ

13

MPCA

Genesis - Vintage

User menu

Seng the me

display. 12 or 24

hours

Seng the

temperature

unit

Seng the me

Set hours

Minute seng

Seng ° C / ° F

Switches from 12 h

AM / PM display on

24

Access to

menu

Parameters Display Handling

OK

conﬁrm with

-

+

Change the value with

or

Login with

OK

conﬁrm with

-

+

Change the value with

or

Login with

OK

conﬁrm with

OK

conﬁrm with

-

+

Change the value with

or

-

+

Change the value with

or

Login with

Remarks

Even if the screen

is blank Press

for 6 seconds

Change the

screens with

To exit the menu,

press

14

MPCA

Genesis - Vintage

User menu

Access to

menu

Parameters Screens Manipulations

OK

conﬁrm with

-

+

Change the value with

or

Login with

OK

conﬁrm with

-

+

Change the value with

or

Login with

OK

conﬁrm with

-

+

Change the value with

or

Login with

Remarks

This parameter is

set to 0 at the

factory. It may be

modiﬁed only in

the case where

there would be a

diﬀerence

between the

seng tempera-

ture and the real

temperature of

the cellar.

This parameter is

set to 0 at the

factory. It may be

modiﬁed only in

the case where

there would be a

gap between the

moisture displayed

and the real humi-

dity of the cellar.

Only available on

model Vintage

Lets venlaon at

low speed when

the air condioner

reaches its setpoint

temperatures and

humidity, to have a

permanent air

circulaon in the

cellar.

It is recommended

to leave this seng

enabled when the

evaporator is

ducng (version

OUT).

Calibrang the

temperature

sensor

Calibraon of

humidity probe

Seng the fan

status when the

setpoint is

reached

Even if the screen

is blank Press

for 6 seconds

Change the

screens with

To exit the menu,

press

15

Alarms codes MPCA

Genesis - Vintage

Two types of errors may appear on the wireless remote control.

Type 1 alarm : The Green and red LED on the front panel ﬂashes.

A warning message appears on the wireless control and buon

ﬂashes when a buon is pressed.

The air condioner connues to operate.

Type 2 alarm : The red LED on the front panel ﬂashes.

A warning message appears on the wireless control and buon

ﬂashes when a buon is pressed.

The air condioner does not work anymore.

Contact your hardware vendor

Once the problem is solved, press the Sync buon on the unit or on

OK

Genesis temperature signal lost

type 2

Lower threshold wine cellar temperature

type 1

Upper threshold wine cellar temperature

type 1

Faulty wine cellar temperature

type 2

Vintage temperature signal lost

type 2

type 1

Upper threshold wine cellar humidity

type 1

type 2

Outside unit temperature signal lost

type 1

Upper threshold outside unit temperature

type 1

Faulty outside unit temperature

type 1

Faulty inside unit motor fan

type 2

Radio signal lost

type 1

AS1c

A SL

A SH

A SO

AS2c

A SL

A SH

AHRH

A SO

AS3c

AS3H

AS3O

AVEc

AVCc

A rF

Faulty outside unit motor fan

Upper threshold wine cellar temperature

Lower threshold wine cellar temperature

Faulty wine cellar temperature

Alarm code Error source

Cellar T° sensor

T° sensor + HR% cellar

(on Vintage model)

Condenser T° sensor

Evaporator fan

condenser fan

wireless communicaon

Type of error

Description

16

How to reset to factory conﬁguraon with te remote controller

Reset

Genesis & Vintage

The reset will change the parameters to their factory value

Set the fan speed, temperature and humidity

Restart the unit

With the remote

Press .

For 2 seconds

Unit starts

If symbol or

ﬂashes, unit is

in stand by mode

Press

unl or

become ﬁxed

Press simultaneously

OK

Push

+10 Seconds

SPC

Maintenance

Maintaining your air condioner cellar

The following maintenance repeated every 6 months operaons will allow your air condio-

ner MPC keep its opmal ways to ensure its longevity and your wines.

CAUTION

Before any maintenance work, switch oﬀ the power supply to the main circuit breaker.

Maintenance of the condenser (hot side)

Remove the front cover using an Allen wrench to access the condenser coil air. Use a vacuum

cleaner to remove dust. Be careful not to damage the ﬁns.

Maintenance of the evaporator (cold side)

Remove the front cover using an Allen wrench to access the evaporator coil air. Use a vacuum

cleaner to remove dust. Be careful not to damage the ﬁns.

Remove the condensate tray with a screwdriver, clean it with water then reinstall it

17

MPCA

Genesis - Vintage

Compressor

Fan

Heater

Wiring diagram

Solenoid valve on vintage

series

Crankcase heater Temperature sensor

Temperature & humidity sensor

on Vintage series

GND

PWM1

TAC

CP HGR KCH EVF CDF POWER Sonde

cond

T°

LLL LL

NNN NN

blue

Yellow

White

Blue

Black

5 x 20

10A GT

LN

T°+HGR

or

On Vintage

model

GND

PWM2

TAC2

Blue

Yellow

White

LNLN

EVF CDF

RC

LN

16 A max

AUX (light)

NC NO

COM

NC

NO

(Example)

Detached pieces

Designation Ref.

1 Compressor 30050077

2 Remote PR20050067

3 Control board PR20050070

4 Light switch

PR20070008

5Probe °C + HRG% 20050002-20070035

6 Fan PR20080082

7Drip tray 40010274

Bent hose PR60010039

Condensate pipe 60010291

4

2

1

6

3

7

5

18

19

Manufacturer’s declaration - Compliance with standards

DECLARATION DU FABRICANT

MANUFACTURER’S CERTIFICATE

GB-SPC-DF-0317

DECLARE QUE NOTRE APPAREIL APPARTENANT A UNE DES GAMMES SUIVANTES :

DECLARES THAT THIS MACHINE BELONGING TO ONE OF THE FOLLOWING RANGES:

SPC 30 EVPL (Genesis-Vintage) - SPC 48 EVPL (Genesis-Vintage) - SPC 82 EVPL (Genesis-Vintage) -

SPC 122 EVPL (Genesis-Vintage) - SPC 170 EVPL (Genesis-Vintage) - SPC 230 EVPL (Genesis-Vintage)

SPC 30 EVG / EVI (Genesis-Vintage) - SPC 48 EVG / EVI (Genesis-Vintage) - SPC 82 EVG / EVI

(Genesis-Vintage) - SPC 122 EVG / EVI (Genesis-Vintage) - SPC 170 EVG (Genesis-Vintage) - SPC 230

EVG (Genesis-Vintage)

SPC 30 EVA (Genesis-Vintage) – SPC 48 EVA (Genesis-Vintage) – SPC 82 EVA (Genesis-Vintage) – SPC

122 EVA (Genesis-Vintage)

MPC 30 (Genesis-Vintage) – MPC 48 (Genesis-Vintage) - MPCA 30 (Genesis-Vintage)

EST CONFORME:

IS IN CONFORMITY WITH

- AUX DISPOSITIONS DES DIRECTIVES EUROPEENNES SUIVANTES ET A LEURS MODIFICATIONS :

- THE REQUIREMENTS OF THE FOLLOWING EUROPEAN MEASURES AND THEIR MODIFICATION :

 2014/35/EU (Basse Tension),



2014/35/EU

(Low Voltage),

 2014/30/EU (Compatibilité électromagnétique),

 2014/30/EU (Electromagnetic compatibility),

 2014/68/EU (Equipements sous pression),

 2011/65/EU (RohS),

- AUX NORMES SUIVANTES :

- THE FOLLOWINGS STANDARDS :

 NF C 15 100 (Installation électriques à basse tension),

 NF C 15 100 (Low voltage installation),

 EN 60204-1 (Equipement électrique des machines),

 EN 60204-1 (Electric equipment of machines),

 NF EN 378-1 à 4 (Systèmes de réfrigération (…) / Exigences de sécurité et d’environnement),

 NF EN 378-1 to 4 (Refrigeration Systems(…) / Safety and environmental requirements),

-

AUX REGLEMENT (CE) 2037/2000 SUR LES SUBSTANCES APPAUVRISSANT LA COUCHE D’OZONE

-

THE REGULATION (EC) 2037/2000 CONCERNING OZONE LAYER DEPLETION PRODUCTS

ET QUE LE MARQUAGE A ETE APPOSE SUR LE MATERIEL.

AND THAT THE MARKING HAS BEEN AFFIXED ON UNIT

Directeur Général

Managing Director

Eric JACQUOT

FRIAX INDUSTRIE - RCS CHAMBERY 477 811 517

ZAC de la Prairie – F73420 VOGLANS

Tel : +33 (4) 79 34 91 84 – Fax : +33 (4) 79 34 91 85 – [email protected]

Site web :www.friax.fr

Boite mail : @friax.fr

info

R

INDUSTRIE

231/233 Rue de la Prairie

F-73420 Voglans

Découvrez notre de cave de rangement pour la cave!

site web: www.visiorack.com

Friax MPCA 20 C Genesis Installation guide

Friax MPCA 20 C Genesis Installation guide

Other documents