Cumberland PowerTrak Auxiliary Fan Switch Owner's manual

Cumberland
Brand
Cumberland
Model
PowerTrak Auxiliary Fan Switch
Type
Owner's manual
Cumberland. • 1004 E. Illinois St. • Assumption, IL 62510 • Phone 1-217-226-4421 • Fax 1-217-226-4420
Manual Part No. 4801-0112 Rev 01/15
POWERTRAK
AUXILIARY SWITCH INSTALLATION
Purpose of Equipment:
To give a signal to turn on or off
equipment when curtain height reaches
the position you set.
Warning!
Disconnect all power sources to PowerTrak before
attempting to install the Auxiliary Switch. Electric Shock
may result.
Tools Required: Drill with 3/16" bit
3/4" Wrench
1/4" Allen Wrench
Pliers
To Set Switch Position:
Manually raise or lower curtains to desired height.
Place template over side even with center of load block
(as shown below at left), then follow the instructions for
installation.
When installation is complete, manually raise and lower
curtain past the switch slowly to be sure that the switch
operates without binding.
Lay template over side of
PowerTrak at desired height.
Mark and Drill holes.
Attach switch and bracket using
the two nuts and bolts provided.
Replace existing setscrews
with new longer setscrews.
Place bracket on new setscrews, and
secure with nuts. Be sure the bracket
can slide from side to side.
Attach one end of tensioning
spring to bracket as shown,
and the other end around the
grease fitting.
Note: Nuts should not be
completely tightened so
that the bracket may slide
back and forth freely.
* Note For Serial Numbers 20625 and higher (DOM 3/4/96), you must add
two ½ inch washers to the setscrews between bracket and load nut.
Cumberland. • 1004 E. Illinois St. • Assumption, IL 62510 • Phone 1-217-226-4421 • Fax 1-217-226-4420
Manual Part No. 4801-0112 Rev 01/15
POWERTRAK
AUXILIARY SWITCH INSTALLATION (Continued)
For 4, 5, or 6 foot PowerTrak machines only:
Replace the brace across the center front of the
Machine. This brace is held in place by four bolts.
Use the original bolts to install the new brace.
Connect the wires from the switch to the
wires from the limit switch harness at the
bottom of the machine.
Use the connection as shown below, to
splice the end of the new wire to any part of
the existing wire. Match pink and tan wires
color to color.
PowerTrak's manufactured before 4/7/97 Serial No's 28809 and lower.
J5 J4 J6 J7
MotorControllerLimit Switches
Lower
Upper
Fan
Switch
5 August 1994 T.E.
PCB135 (Rev A)
From Breaker
for Fans
From Power Source to
Thermostats and
Contactors
From Breaker
for Fans
Circuit board in Power Trak
Two Single Stage Thermostats
Contactors in CCS Panel
All wiring must be performed in
accordance with all National and Local
Electric Codes. Installation by qualified
electrician recommended.
To Fans
To Fans
Pink
Tan
To Limit
Switches
Pink
Tan
Cumberland. • 1004 E. Illinois St. • Assumption, IL 62510 • Phone 1-217-226-4421 • Fax 1-217-226-4420
Manual Part No. 4801-0112 Rev 01/15
POWERTRAK
AUXILIARY SWITCH INSTALLATION (Continued)
PowerTrak
AUX
SWITCH CONTROLLER AC IN
HOT
NEUT.
LOWER
GND.
HOT
OUT
CLOSE
IN
OPEN
IN
COM
UPPER
From Breaker
for Fans
From Power Source to
Thermostats and
Contactors
From Breaker
for Fans
Two Single Stage Thermostats
Contactors in CCS Panel
All wiring must be performed in
accordance with all National and Local
Electric Codes. Installation by qualified
electrician recommended.
To Fans
To Fans
Pink
Tan
PowerTrak's manufactured after 4/7/97 Serial No's 28810 and later.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Cumberland PowerTrak Auxiliary Fan Switch Owner's manual

Cumberland
Brand
Cumberland
Model
PowerTrak Auxiliary Fan Switch
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents