Symmons H801S56 Installation guide

Symmons
Brand
Symmons
Model
H801S56
Type
Installation guide

This manual is also suitable for

Remove “S” modifier for Less Soap Dish
RS Recessed soap dish
SH Shortened handle
Valve Modifiers
56 Metering Show-O and Pressure Balance Valve Combo
Shower Modifiers
L1 Less showerhead
1.5 1.5 gpm Shower Head
Surface Mounted Shower System
Operation & Maintenance Manual
H801S: Through wall piping configuration with soap dish
Displayed: H801S
Remove “S” modifier
for less soap dish
Dimensions
Modifications
Compliance
Measurements
A27-9/16”, 700 mm
B2-15/16”, 75 mm
C20”, 508 mm
D4-5/8”, 118 mm
E8-3/16”, 208 mm
F4-3/4”, 121 mm
G2-15/16”, 75 mm
H5-5/8”, 143.5 mm
I20”, 508 mm
J2-1/2”, 63.5 mm
K6-11/16”, 169.5 mm
A
B
C
D
EF
G
H
I
KJ
- ASME A112.18.1/CSA B125.1
- ASSE 1016
Job/Location
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engineer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contractor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For ADA compliance (Americans with
Disabilities Act) consult ADAAG or your
state regulations for proper product choice
and mounting locations.
HYDAPIPE®
Architectural/Engineering Specification
Pressure Balancing mixing valve with screw driver service stops
and adjustable stop screw to limit handle turn. Showerhead
Fre-Flo, all brass with ball joint. Attached soap dish and sloped
metal top cap. Stainless steel covering to be 18 gauge with #4
brush finish.
Installation
Symmons Industries, Inc.
■
31 Brooks Drive, Braintree, MA 02184
■
Phone: (800) 796-6667
■
Fax: (800) 961-9621
Copyright © 2021 Symmons Industries, Inc.
■
symmons.com
■
gethelp@symmons.com
■
ZV-3450 REV 0
■
070221
INSTALLATION:
1. With provided vandal resistant bit remove 2 vandal-proof screws
(A) holding stain less steel unit cover (D) to valve and piping assembly.
2. Remove handle and dome assembly (B)
3. Remove showerhead assembly (C)
4. Remove unit cover (D)
5. Use valve assembly to mark mounting holes on desired surface
6. Mount valve and piping assembly to wall with screws and anchors
provided.
7. Connect supply piping.
8. Replace unit covering and fasten with vandal proof screws (A)
9. Replace handle Assembly (B) and showerhead Assembly (C)
C
B
A
D
For ADA compliance (American Disabilities Act) consult ADAAG or your state
regulations for proper product choice and mounting heights. ADAAG does permit
a fixed shower head mounted 48’’ above the floor in unmonitored facilities where
vandalism may be a problem.
  • Page 1 1
  • Page 2 2

Symmons H801S56 Installation guide

Symmons
Brand
Symmons
Model
H801S56
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents